Related Manuals for STM ROCKETBOX 2.0
Summary of Contents for STM ROCKETBOX 2.0
- Page 1 ( 5 0 9 ) 2 0 4 - 3 1 4 8 ( C A L L O R T E X T ) | S T M C A N N A . C O M | S A L E S @ S T M C A N N A . C O M...
- Page 2 WEIGHT & Approximately 300 lbs R O C K E T B O X 2 . 0 ™ DIMENSIONS Machine Dimensions 24" L x 37" H x 27" W USER MANUAL V1.3 VOLUME 453 Pre-Rolls Every Cycle CAPACITY Standard 110V POWER 8 Full Load Amps 5-1/2 ft.
-
Page 3: Table Of Contents
T A B L E O F C O N T E N T S Table of Contents ......... 1 Startup Menu ..........11 Break-In Procedure ........2 Density Test Mode ........12 Components ..........3 Density Testing ........... 13 Adjustable Top Tray ........ -
Page 4: Break-In Procedure
G U I D E L I N E S T O B R E A K - I N Y O U R R O C K E T B O X ™ STM. Our goal is to bring our customers the very best in product quality and customer service. -
Page 5: Components
C O M P O N E N T S 5. Power Switch 1. Rubber Flaps - Prevents material from falling into the base of machine. 1. Rubber Flaps 2. Guide Rods - Used for guiding the top and bottom trays into machine. 2. - Page 6 C O M P O N E N T S 8. Loading Box 8. Loading Box - Holds bottom tray to load cones and unload top tray. 9. Top Tray - Placed on top of bottom 12. Reset Brackets tray. Only used for machine operation. 9.
-
Page 7: Adjustable Top Tray
(2) Removable Reset Brackets the overall volume of the pre-rolls. The RocketBox 2.0 is pre-installed with an Adjustable Top Tray. The default adjustment is set at at ¼", easily adjusted with a 7/16" end wrench. - Page 8 I n c l u d e d R e s e t B r a c k e t s T R A Y A S S E M B L Y The RocketBox 2.0 includes (2) removable Reset Brackets to reset the height of the Top Tray Top Tray to the default 1/4"...
-
Page 9: Lift Plate
L I F T P L A T E The Lift Plate rests on the bottom of the shaker box to help level the cones for even filling. The Lift Plate uses (4) Riser Bolts to adjust for 84 mm, 98 mm, and 109 mm tray sizes. The Lift Plate is set for 109 mm by default. -
Page 10: Getting Started
G E T T I N G S T A R T E D S U G G E S T E D T O O L S A N D A C C E S S O R I E S P O W E R I N G O N T H E R O C K E T B O X Scoop for Material Thousandths Scale... -
Page 11: Touch Screen
T O U C H S C R E E N W E L C O M E S C R E E N T R A I N I N G M O D U L E The welcome screen will appear after powering on the Select USER MANUAL to view the manual, or select machine. - Page 12 T O U C H S C R E E N D A T A L O G E V A L U A T E I N F O R M A T I O N Records the settings of the last 100 runs. Additionally, Gives additional information and tips to improve the data log can be used for troubleshooting purposes.
-
Page 13: Startup Menu
S T A R T U P M E N U S T A R T U P M E N U The startup menu will appear after selecting START on the Welcome screen. On this screen, the operator will select the cone size and weight variance preferred. -
Page 14: Density Test Mode
D E N S I T Y T E S T M O D E D E N S I T Y T E S T M O D E To attain the variance goal, performing a density test is crucial for success. -
Page 15: Density Testing
D E N S I T Y T E S T I N G P E R F O R M I N G A D E N S I T Y T E S T The RocketBox™ 2.0's built-in Density Calculator assists Tare empty 10 mL beaker on thousandths scale. - Page 16 D E N S I T Y T E S T I N G H e l p f u l T i p s Repeat density test 3x and average out for optimal results. Hold beaker in place during density testing. It is recommended to use a thousandths scale for accuracy.
-
Page 17: Operation Of Machine
O P E R A T I O N O F M A C H I N E Insert the tray into the RocketBox™. Add washers and wingnuts to secure in place. Adjust the settings on the touch screen if necessary. -
Page 18: Loading & Unloading Cones
L O A D I N G A N D U N L O A D I N G C O N E S L O A D I N G C O N E S Always use good quality paper cones and discard all papers that appear to be defective. -
Page 19: Cleaning & Maintenance
C L E A N I N G A N D M A I N T E N A N C E H O W T O C L E A N Each tray can be separated and cleaned using regular soap and water, removing all residue. -
Page 20: Terms Of Business
All products are first-come-first-serve and that receipt of payment is required in order to receive a confirmed shipping date in the queue. Due to high demands, certain items may have a lead time of 4-8 weeks or more from payment date, unless otherwise stated. Following the receipt of an invoice, STM Canna must receive payment within a maximum of 7 days before the invoice expires –... - Page 21 T E R M S All orders must be paid in full before the order is placed. Order quotes expire within 10 days. STM Canna & STM Supply reserve the right to specify collection by certified check, money order, or company check. Personal checks are not accepted.
- Page 22 We may ask you for pictures, video, descriptions, and other identifying information to make a determination. If you are unable to provide adequate documentation requested, your return request will be denied. If your item is deemed defective, which is solely at STM’s discretion, we will issue you an RMA # which you will need to place in and on the package.
- Page 23 L I A B I L I T Y The purchaser of any products releases the manufacturer of those parts and STM Canna from all liabilities pertaining to use of the products. C L A I M S Since ownership of product transfers at the FOB point, claims for damaged, lost, or short shipments must be made at the time of receipt.
Need help?
Do you have a question about the ROCKETBOX 2.0 and is the answer not in the manual?
Questions and answers