Toolson PRO-AS 360 Operating Manual page 16

charging cable to the charging connection. The charging
process starts as soon as the charging cable is connec­
ted to the charging adapter.
Recharging the battery (Fig. 1/2)
1. Connect the charger plug to the charging socket (5) of
the device.
2. Schließen Sie das Ladegerät (8) an eine Steckdose
an.
3. When the battery is fully recharged unplug the battery
charger (8) from the mains.
Battery charging
Battery charging
Battery fully charged
Notice! The handle may become a little warm during the
charging process. This is normal.
If the battery fails to charge, please check
• whether there is voltage at the socket outlet
• whether there is good contact at the charging contacts
of the charging unit
If the battery still fails to charge, send
• the charging unit
• and the screwdriver
to our customer service center.
Timely recharging of the battery will help it serve you
well for a long time. You must recharge the battery when
you notice that the power of the cordless screwdriver
drops.
Changeover switch (Fig. 3/Item 7)
The slide switch above the On/Off switch is for setting
the direction of rotation of the cordless screwdriver and
for preventing the cordless screwdriver from being swit­
ched on inadvertently. You can select between clockwi­
se and counterclockwise rotation. Change the direction
of rotation only when the equipment is at a standstill. If
you fail to observe this point, the gearing may become
damaged. When the slide switch is in the middle positi­
on, the On/Off switch is blocked.
On/Off switch (Fig. 3 / Item 6)
Press the On/Off switch to switch the cordless screwdri­
ver on. Release the On/Off switch again to switch it off .
LED lamp (Fig. 3/Item 2)
The LED lamp (2) can be used to additionally illuminate
the area where you want to drill or screw. The LED lamp
(2) will be lit automatically as soon as you press the On/
Off switch (6).
Checking the battery charge level (Fig. 1/4)
The battery's charge level is indicated by the charge
state indicator (4).
16 І 136
The state of charge of the battery is displayed by illumi­
nating the appropriate LED lights. In order to activate
the display, the on/off switch (6) must be pressed.
All the LEDs are lit:
The battery is fully charged.
The yellow and red LEDs are lit:
The battery has an adequate remaining charge.
Red LED:
The battery is empty, recharge the battery.
Torque setting (Fig. 4 / Item 3)
The torque for a particular screw size is set with the
setting ring (3). The torque is dependent on a number of
factors:
• On the type and hardness of the material involved
• On the type and length of the screws used
• On the requirements that the screw connection has to
satisfy
The grating disengagement of the coupling indicates
that the selected torque level has been reached.
Notice! Only ever adjust the setting ring when the
equipment is at a standstill.
Changing the bit (Fig. 5)
Warning! Set the changeover switch to its center
position whenever you carry out any work (for example
changing the bit, maintenance , etc.) on the cordless
screwdriver.
• Pull back and hold the locking sleeve (10).
• Insert the bit (a) in the bit chuck (1) and let go of the
locking sleeve (10).
• Check that the bit is locked in placed by pulling on it.
Screws
It is advisable to use self­centering screws (e.g. Torx,
cross recessed head) as these will enable you to work
safely and reliably. Always make sure that the bit used is
of the same size and shape as the screw.
Maintenance
Danger!
Always pull out the mains power plug before starting any
cleaning work.
Cleaning
• Keep all safety devices, air vents and the motor
housing free of dirt and dust as far as possible. Wipe
the equipment with a clean cloth or blow it with com­
pressed air at low pressure.
• We recommend that you clean the device immediately
each time you have finished using it.
• Clean the equipment regularly with a moist cloth
and some soft soap. Do not use cleaning agents or
solvents; these could attack the plastic parts of the
equipment. Ensure that no water can seep into the
device. The ingress of water into an electric tool incre­
ases the risk of an electric shock.
Maintenance
There are no parts inside the equipment which require
additional maintenance.