Advertisement
Quick Links
LIGHT HEAD INSTALLATION
Solar Power Generator with Pneumatic Light Tower
Mast Part# SPLT-1.59K-800A-30-4X100W-LED-MS
The solar trailer ships with the light head removed to prevent damage during
transport. Follow the steps below for installing or removing the light head.
1. Locate the light head.
2. The light head is equipped with a T-
Handle.
3. Make sure the T-Handle is loose, to
allow the head to slide over the top
stage of the mast.
4. Using a pair of slings, wrap both slings around the light head in between
the lights on both sides.
5. Attach the slings to a forklift or other lifting device.
SPLT-1.59K-800A-30-4X100W-LED-MS
COLOR MAY VARY
Larson Electronics LLC
6. With 2 people holding the light head steady, slowly raise the light head
above the mast.
7. A ladder will need to be placed on both sides of the mast, in order for 2
people to guide the head in to place.
8. Once the light head is on top of the light mast, tighten the T-Handle to
ensure the light head is safely secured to the top of the mast.
9. Make the electrical connections for the
lights. Repeat this process in reverse
order for removing the light head.
10. Proceed to the OPERATION MANUAL for operating the unit.
P: 800-369-6671 | INTL: 903-498-3363 F: 903-498-3364
ver.0118-1
9419 US-HWY 175
Kemp, TX 75143 USA
sales@larsonelectronics.com
www.larsonelectronics.com
1
Advertisement
Summary of Contents for Larson Electronics SPLT-1.59K-800A-30-4X100W-LED-MS
- Page 1 LIGHT HEAD INSTALLATION above the mast. Solar Power Generator with Pneumatic Light Tower Mast Part# SPLT-1.59K-800A-30-4X100W-LED-MS The solar trailer ships with the light head removed to prevent damage during transport. Follow the steps below for installing or removing the light head.
- Page 2 OPERATION MANUAL Solar Power Generator with Pneumatic Light Tower Mast FRONT HITCH JACK Part# SPLT-1.59K-800A-30-4X100W-LED-MS LEVELING JACK Once the trailer has been disconnected from the hitch of the tow vehicle, extend the remaining jacks. There are (2) leveling jacks located on the back and (2) jacks located on the front of the trailer.
-
Page 3: Support Leg
Crank the winch clockwise to extend the solar trailer. panels and twist each locking pin back into their closed position so they will snap in place once the mast is fully elevated. Once installed, the trailer is ready to be powered on. SPLT-1.59K-800A-30-4X100W-LED-MS Larson Electronics LLC... -
Page 4: Powering The Unit
NOTE: Leaving the lights on during charge will greatly diminish run to prolong battery life. The unit will not come on until voltage has reached time of the lights. 24.7V. The unit will shut off at 24V. The unit is now deployed! SPLT-1.59K-800A-30-4X100W-LED-MS Larson Electronics LLC... -
Page 5: Motion Sensor Operation
Turn hand winch counter-clockwise to ALL connections and reset. Check for foreign objects or water leaks. lower solar panels fully. Check cables to Contact manufacturer for further troubleshooting. ensure they do not get caught while lowering. SPLT-1.59K-800A-30-4X100W-LED-MS Larson Electronics LLC... - Page 6 Make sure everything is properly latched and secure before towing. The unit is ready for transport. 9419 US-HWY 175 Kemp, TX 75143 USA P: 800-369-6671 | INTL: 903-498-3363 F: 903-498-3364 sales@larsonelectronics.com www.larsonelectronics.com SPLT-1.59K-800A-30-4X100W-LED-MS Larson Electronics LLC...