Mark Levinson 5302 Owner's Manual
  1. Manuals
  2. Brands
  3. Mark Levinson Manuals
  4. Amplifier
  5. 5302
  6. Owner's manual

Mark Levinson 5302 Owner's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
N
5302
0
POWER AMPLIFIER
OWNER'S MANUAL

Advertisement

Table of Contents
loading

Related Manuals for Mark Levinson 5302

Summary of Contents for Mark Levinson 5302

  • Page 1 5302 POWER AMPLIFIER OWNER’S MANUAL...

  • Page 3: Table Of Contents

    Power requirements, operating states Connections Rear panel overviews External component connections Control Front panel overview Browser setup page (BSP) Setup BSP setup menu Firmware Power Network Trigger Faults Config Utility menu Advanced updates menu Troubleshooting Specifications 5302 POWER AMPLIFIER OWNER’S MANUAL...

  • Page 4: Overview

    OVERVIEW INTRODUCING THE MARK LEVINSON N 5302 POWER AMPLIFIER Congratulations on your purchase of a Mark Levinson ® power amplifier. You now possess one of the finest audio reproduction devices in the world, a product that will provide an exceptional music listening experience for years to come.

  • Page 5: Installation

    1 x Owner’s manual 1 x Safety information sheet Please register your N 5302 within 15 days of your purchase. Register online at www.MarkLevinson.com. Retain your original, dated sales receipt as proof of warranty coverage.

  • Page 6: Power Requirements, Operating States

    Off: The AC mains power is disconnected by removing the power cord from the rear panel. The N 5302 is configured at the factory for 100, 115, or 230 Standby: The Standby mode has three settings that can VAC power operation at 50Hz or 60Hz. Before operating the...

  • Page 7: Connections

    IR In Trigger AC Mains Inlet Bridged Operation for Updates In and Out Negative (-) Output Terminal Fuse Compartment Bridged Operation Ethernet RS232 Stereo/Bridged (see rear-panel Positive (+) Output Terminal DB9F Selector Switch labeling for value) 5302 POWER AMPLIFIER OWNER’S MANUAL...

  • Page 8: External Component Connections

    5302 and all associated components are powered off and balanced XLR type output connectors. When using the disconnected from electrical outlets. 5302 in bridged mode, use the left channel input only and set the Stereo/Bridged mode switch to Bridged. One balanced and one single-ended (unbalanced) connector Balanced are available for each audio channel input.
  • Page 9 For bare wire and spade lugs, first loosen the binding When using the N 5302 in bridged mode connect the speaker post thumb nut, insert the wire or spade and finger- positive (+) cable to the left channel red (positive, or +) binding tighten the nut.
  • Page 10 (LAN) via an Ethernet to the N 5302 when the supplied power cord is connected cable. (See page 13 for more detailed firmware update from it to an AC electrical outlet. This should be the LAST instructions.)
  • Page 11 CONNECTIONS EXTERNAL COMPONENTS CONNECTIONS N 5302 STEREO MODE Source Player Preamplifier or Source Player with Volume Control 5302 Amplifier Right Left Speaker Speaker 5302 POWER AMPLIFIER OWNER’S MANUAL...
  • Page 12 CONNECTIONS EXTERNAL COMPONENTS CONNECTIONS N 5302 BRIDGED MODE Source Player Preamplifier or Source Player with Volume Control 5302 Amplifier Right Speaker 5302 Amplifier Left Speaker 5302 POWER AMPLIFIER OWNER’S MANUAL...

  • Page 13: Control

    CONTROL CONTROL The N 5302 is highly flexible and allows a variety of means of setup and control including IP, IR (input), RS232, trigger and 3rd party control systems. For most applications simply switching between Standby and On would be the extent of the control needed.

  • Page 14: Browser Setup Page (Bsp)

    In order to access the BSP, you must first connect the unit to your Local Area Network (LAN). Connect the Ethernet port on the rear panel of the N 5302 to an Ethernet port on your home network’s router, switch or hub with a Category 5e or Category 6 Ethernet cable.

  • Page 15: Setup

    SETUP SETUP Connect your Mark Levinson amplifier to a PC or tablet via Browser method: your home network as described above and open a browser. Make sure your unit is connected to a network with Internet Network speed and quality of the connection will affect the access.

  • Page 16: Power

    Green: This mode removes power from almost all of the 5302’s circuits, allowing the unit to be activated only via a wired IR control signal, a 5V – 12V trigger voltage or a press of the Standby button. This mode provides maximum power conservation and is the factory-default Standby mode.

  • Page 17: Network

    MAC address). Use your mouse and keyboard components. to change the network name. Pulsed: Some products (such as some older Mark Levinson Current Gateway: Displays the Gateway IP address. This components) require a pulsed trigger signal. setting is informational only and does not provide any user adjustments.

  • Page 18: Faults

    Save the webpage to your PC or a thumb drive. Config Import: Press Enter to import the setup configuration file that was saved in the export process. Restore: Restores all N 5302 parameters to their factory- default conditions. 5302 POWER AMPLIFIER OWNER’S MANUAL...

  • Page 19: Utility Menu

    To check if your unit’s firmware is up to date, go to the 5302 product page on www.MarkLevinson.com, select the Downloads tab and look for the latest firmware update file. If there is a later version, you may use either of the options described on page 13 to update your unit.

  • Page 20: Troubleshooting

    TROUBLESHOOTING Incorrect operation is sometimes mistaken for malfunction. If problems occur, see this section for troubleshooting information. If problems persist, contact your authorized Mark Levinson dealer. NO POWER Examine the power cord to ensure that it is connected to both the AC mains connector and a working, unswitched electrical outlet.
  • Page 21 Repeat the process two more times. Restore factory-default settings (See Config tab on Setup menu on the Browser Setup Page. See page 16). Contact your authorized Mark Levinson dealer. Contact Mark Levinson Customer Service at 888-691-4171 or marklevinson.com. 5302 POWER AMPLIFIER OWNER’S MANUAL...

  • Page 22: Specifications

    <2Hz to 80kHz, +0/–3dB Input Impedance: Balanced (XLR): 100kΩ Unbalanced/single-ended (RCA): 50kΩ Input Connectors: 1 pair balanced line-level inputs (XLR) 1 pair single-ended line-level inputs (RCA) Output Connectors: 2 pairs high current multi-way binding posts 5302 POWER AMPLIFIER OWNER’S MANUAL...
  • Page 23 Control Connectors: 1 RS-232 port (DB-9) 1 Ethernet port (RJ-45) 1 USB port for firmware updates (USB-A) 1 baseband IR input (⅛"/3.5mm phone jack) 1 programmable 12V DC trigger output, 100mA maximum (⅛"/3.5mm phone jack) 1 programmable 12V DC trigger input (⅛”/3.5mm phone jack) Power Consumption: Maximum: 1000W On, idle (stereo mode): 90W...
  • Page 24 Northridge, CA 91329 USA © 2020 HARMAN International Industries, Incorporated. All rights reserved. Mark Levinson is a registered trademark of HARMAN International Industries, Incorporated. Other company and product names may be trademarks of the respective companies with which they are associated.

Table of Contents