LEGRAND Raritan PX Installation Manual

Raritan PX
This installation guide explains how to install power cords
on Raritan PX products that do not come with a factory
installed power cord. This type of product, such as
PX2-4550XU and in-line monitors, provides the flexibility
of using a power cord with the style you need.
Safety Guidelines
WARNING! These instructions are not for products with
factory-installed flexible cords. Do not open a Raritan product with
a factory-installed cord.
WARNING! Do not replace the cable gland. The chassis is punched
for the correctly-sized gland and is not for different wiring methods
such as conduit.
WARNING! These instructions must be performed by a licensed
electrician.
WARNING! Raritan products must not be serviced while energized.
Before servicing, (a) disconnect from power, (b) disconnect any
devices plugged into the product's receptacles, and (c) disconnect
all interconnect cables.
WARNING! Read and understand all sections in this guide before
installing or operating this product.
WARNING! Connect this product to an AC power source whose
voltage is within the range specified on the product's nameplate.
Operating this product outside the nameplate voltage range may
result in electric shock, fire, personal injury and death.
WARNING! Connect this product to an AC power source that is
current limited by a suitably rated fuse or circuit breaker in
accordance with national and local electrical codes. Operating this
product without proper current limiting may result in electric
shock, fire, personal injury and death.
WARNING! Connect this product to a protective earth ground.
Never use a "ground lift adaptor" between the product's plug and
the wall receptacle. Failure to connect to a protective earth ground
may result in electric shock, fire, personal injury and death.
WARNING! This product contains no user serviceable parts. Do not
open, alter or disassemble this product except as described in this
manual. Failure to comply with this warning may result in electric
shock, personal injury and death.
WARNING! Use this product in a dry location. Failure to use this
product in a dry location may result in electric shock, personal
injury and death.
WARNING! Do not rely on this product's receptacle lamps,
receptacle relay switches or any other receptacle power on/off
indicator to determine whether power is being supplied to a
receptacle. Unplug a device connected to this product before
performing repair, maintenance or service on the device. Failure to
unplug a device before servicing it may result in electric shock, fire,
personal injury and death.
WARNING! Only use this product to power information technology
equipment that has a UL/IEC 60950-1 or equivalent rating.
Raritan PX Power Cord Installation Guide
PowerCord_InstallGuide_1B_3.6.10  255-80-6083-00 RoHS
POWER CORD INSTALLATION GUIDE
Attempting to power non-rated devices may result in electric
shock, fire, personal injury and death.
WARNING! Do not use a Raritan product containing outlet relays to
power large inductive loads such as motors or compressors.
Attempting to power a large inductive load may result in damage to
the relay.
WARNING! Do not use this product to power critical patient care
equipment, fire or smoke alarm systems. Use of this product to
power such equipment may result in personal injury and death.
WARNING! Assembly of this product's line cord and/or plug must
be performed by a licensed electrician and the line cord or plugs
used must be suitably rated based on the product's nameplate
ratings and national and local electrical codes. Assembly by
unlicensed electricians or failure to use suitably rated line cords or
plugs may result in electric shock, fire, personal injury or death.
WARNING! This product contains a chemical known to the State of
California to cause cancer, birth defects, or other reproductive
harm.
QS Rule
Safety Instructions
1. Installation of this product should only be performed by a
licensed electrician.
2. Make sure the line cord is disconnected from power before
physically mounting or moving the location of this product.
3. This product is intended to be located in an equipment rack in
an information technology room. In the United States,
installation must comply and be done in accordance with NEC
(2011) Article 645 Information Technology Equipment.
4. This product is designed to be used within an electronic
equipment rack. The metal case of this product is electrically
bonded to the line cord ground wire. A threaded grounding
point on the case may be used as an additional means of
protectively grounding this product and the rack.
5. Examine the branch circuit receptacle that will supply electric
power to this product. Make sure the receptacle's power lines,
neutral and protective earth ground pins are wired correctly
and are the correct voltage and phase. Make sure the branch
circuit receptacle is protected by a suitably rated fuse or circuit
breaker.
6. If the product is a model that contains receptacles that can be
switched on/off, electric power may still be present at a
receptacle even when it is switched off.
QS Rule
1