Page 1
Notice of Copyright Protection UNDERSTANDING OF THE OWNERS MANUAL Copyright 2020, by U.S.SAWS . All rights reserved. This work may not be reproduced or disseminated in whole or in part by any WHEN OPERATING THIS MACHINE means without the prior written permission of U.S.SAWS...
The information and specifications included in this publication were in effect at the time of approval for printing. U.S.SAWS reserves the right, however, to discontinue or change specifications or design at any time with- CAUTION: Indicates a potentially hazardous situation that, if not avoided out notice and without incurring any obligation.
You must be qualified for safe operation of the U.S.SAWS CC-100 machine. You must clearly understand the written instructions supplied by U.S.SAWS, be trained - including actual operation - & know the safety Rules for safer operation ules for safer operation rules &...
Do not operate this machine unless you have received operational and 4.15 AVOID CONTACT WITH HOT BLADE AND BLADE GUARD. maintenance training from a U.S.SAWS representative or from an autho- The blade and blade guard become hot during operation and remain hot rized distributor for U.S.SAWS.
Page 5
S A F E T Y I N S T R U C T I O N S 4.25 STORE IDLE EQUIPMENT. 4.38 WHEN REPLACING A PART, USE THE SAME TYPE The machine, blades and tools should be stored in a dry and secure loca- AND QUALITY.
U.S.SAWS vacuum at all times when equipment is being used.
Page 7
P R E-O P E R AT I O N C H E C K L I S T Rules for safer operation 7,500 MAX. RPM Verify that the lever is disengaged or released, and the Honda Read and understand Use only diamond blades (steel engine switch and fuel valve lever are in the OFF position.
O P E R AT I O N 6.2.2 With engine in the OFF position, loosen the 3/8-inch hex nut by turn- ing it clockwise. Then turn the caster adjustment nut counterclockwise to lower CAUTION: Running the CC-100 generates heat in the engine, engine muffler, the dust brush or clockwise to raise the dust brush.
PA R T S B R E A K D O W N Figure 18 CC-100 SERIES SAWS (1) SX90193 (2) US32404 (3) US31074 (4) US59051 (28) SX90165 (5) US31049 (29) 05-60474 (6) US31119 (30) SX90172 (7) SX90160 (8) US31054 (31) SX92008 (9) SX90163 (32) SX90168...
Page 10
PA R T S B R E A K D O W N ITEM QUANTITY PART NUMBER DESCRIPTION SX90193 BALL KNOB US32404 RIBBED HANDLE GRIP US31074 1/4-20 X 2-3/4” HEX HEAD BOLT US59051 TWO ARM CLAMPING KNOB 5/16-18 US31049 SPANNER BUSHING 3/8ID X 1/2OD X 1-9/16 LONG US31119 5/16-18X2 COACH BOLT SX90160...
Page 11
PA R T S B R E A K D O W N ITEM QUANTITY PART NUMBER DESCRIPTION SX92000 BLADE SHAFT PULLEY US31351-2 1/2”-13 X 1-1/2” HEX HEAD BOLT US31058 1/2”HARDENED SAE FLAT WASHER US31351-1 1/2”-13 NYLOCK NUT SX90177 FLANGE BEARING 2 BOLT 1” BORE SX50250 1/4”-20X3/8”...
Page 12
R E C O M M E N D E D B L A D E S WARNING: Recommended accessories for this tool including blades are listed in this manual or are available by calling customer service. The use of any other attachment or accessory might be hazardous. CC-100 premium dry cut diamond blades, medium bond Table 1 - Dry cut diamond blade list (* All blades listed are designed with CC-100 drive pin holes) Part Number...
Warranty This document is to be used as a guide in determining warranty policies and procedures for U.S.SAWS and its U.S.SAWS products. It is to be used in determining whether a warranty is justified and as a procedural guide in completing a U.S.SAWS warranty claim form.
Page 14
FILL OUT THE ATTACHED CARD COMPLETELY AND ACCURATELY. WARRANTY REGISTRATION CARD IMPORTANT! To ensure that your U.S.SAWS machine is covered under warranty, please fill in the following information and mail or fax it to U.S.SAWS, 8004B E. Broadway Ave. Tampa, FL 33619, Fax No. 714-434-7299...