Advertisement
4.25
STORE IDLE EQUIPMENT.
The machine, blades and tools should be stored in a dry and secure loca-
tion when not in use. Keep equipment out of reach of children.
4.26
DO NOT FORCE SAW.
The saw will do the job better and safer at the rate for which it was de-
signed.
4.27
OBTAIN SAFETY DATA SHEET (SDS) FOR ALL
WORK SURFACE MATERIALS.
This includes primers, all coatings, adhesives, tile and crack filling materi-
als, etc. Do not attempt to cut, clean out or remove material without SDS
information. Consult SDS sheet for hazards information. Be aware that
some materials are explosive as a dust.
4.28
DO NOT OVERREACH.
Keep proper footing and balance at all times.
4.29
MAINTAIN MACHINE WITH CARE.
Keep machine clean and follow maintenance procedures for better and
safer performance. Keep handles dry, clean, and free from oil and grease.
Follow instructions for lubricating and changing accessories.
4.30
REMOVE ADJUSTING TOOLS.
Form a habit of checking to see that tools such as adjusting wrenches are
removed from the machine and properly stored before starting the engine.
4.31
STAY ALERT.
Watch what you are doing. Use common sense. Do not operate machine
when you are tired or fatigued.
4.32
DO NOT USE DRUGS, ALCOHOL, MEDICATION.
Do not operate machine while under the influence of drugs, alcohol,
or any medication.
4.33
KEEP THE RIGHT PARTS IN THE RIGHT POSITIONS.
Do not operate machine with parts missing or improperly mounted.
4.34
CHECK DAMAGED PARTS.
Verify all machine guards are in good condition and will function properly
before using the machine. Check for alignment of moving parts, binding of
moving parts, breakage of parts, mounting, and any other conditions that
may affect machine operation. A guard, power switch or other part that is
damaged should be properly repaired or replaced by an authorized service
center unless indicated elsewhere in this instruction manual. Do not oper-
ate machine if lever or engine on/off switch does not function properly.
4.35
SECURELY MOUNT ACCESSORIES AND BLADES TO THE MA-
CHINE.
Extra care must be taken when using saws on an elevated location to pre-
vent injury to someone on a lower level in the event the tool or accessory
should drop. Do not operate without fall protection for operator and debris
protection for public.
4.36
NEVER TOUCH THE MOVING PARTS.
Never touch moving parts such as blades, belts and others.
4.37
STOP OPERATION IMMEDIATELY IF ANY ABNORMALITY IS
DETECTED.
Stop using machine immediately if any abnormalities are observed during
operation. Examples of abnormalities include unusual noise and vibration.
S A F E T Y I N S T R U C T I O N S
Surface Prep
Division
4.38
WHEN REPLACING A PART, USE THE SAME TYPE
AND QUALITY.
When replacing a component part with a new one, use only the same
type and quality of new part. Never attempt to repair a machine if you are
unfamiliar with proper procedures and techniques required.
4.39
REFUEL WITH CARE.
Gasoline is extremely flammable. Gasoline vapor can explode. Refuel out-
doors, in a well ventilated area, with the engine in the OFF position. Never
smoke near gasoline and keep other flames and sparks away. Always store
gasoline in an approved container. If any gasoline is spilled, make sure the
area is dry before starting the engine.
4.40
NEVER DISABLE THE LEVER.
Do not modify, disable, or attempt to permanently engage the lever. Do not
operate a machine if lever is not functioning. This could lead to serious
injury or death.
4.41
LOAD AND UNLOAD SAFELY.
Use proper heavy lifting procedures. Read & understand manuals before
loading & unloading.
4.42
STORAGE.
Always store equipment properly when it is not being used. Equipment
should be stored in a clean, dry location and out of reach of children.
4.43
SAVE THESE INSTRUCTIONS.
Refer to this operations and maintenance manual as well as any addition-
al instructions included from other manufacturers and organizations such
as Honda® and the Masonry and Concrete Saw Manufacturers Institute®.
Never permit anyone to operate the machine without proper instructions.
DUST WARNING
Cutting, especially when DRY cutting, generates dust that comes
from the material being cut, which frequently contains silica.
Silica is a basic component of sand, quartz, brick clay, granite and
numerous other minerals and rocks. Exposure to excessive amount of
such dust can cause:
• Respiratory diseases (affecting your ability to breath), including
chronic bronchitis, silicosis and pulmonary fibrosis from exposure
to silica. These diseases may be fatal;
• Skin irritation and rash; and
• Cancer according to NTP* and IARC*
* National Toxicology Program, International Agency for Research
on Cancer
Take precautionary steps
• Avoid inhalation of and skin contact with dust, mist and fumes;
• Wet cut when feasible, to minimize dust;
• Wear and ensure that all bystanders wear appropriate respiratory
protection such as dust masks designed to filter out microscopic
particles. (See OSHA 29 CFR Part 1910.1200)
California Prop 65 Warning: Use of this product can cause exposure to
materials known to the State of California to cause cancer and/or birth
defects or other reproductive harm.
P: 877-817- 6687 F: 813-621-7125
Visit us at www.ussaws.com
sales@ussaws.com
5
Advertisement
