Advertisement
P R E-O P E R AT I O N C H E C K L I S T
5.0
Pre-operation checklist
5.0
PRE-OPERATION CHECKLIST
Figure 1 - Warning label - read and understand manual
F F i i g g u u r r e e 3 3 - - W W a a r r n n i i n n g g l l a a b b e e l l - - r r e e a a d d a a n n d d u u n n d d e e r r s s t t a a n n d d m m a a n n u u a a l l
5.1
Start by reading the entire Honda Engines Owner's Manual,
Rx for Diamond Blade Safety, and Rx for Concrete Saws by the
ire Honda Engines Owner's Manual, Rx for Diamond Blade Safety, and Rx for Concrete
and Concrete Saw Manufacturers Institute. Then, read the entire JS operations and
Masonry and Concrete Saw Manufacturers Institute. Then, read the
familiar with the machine's parts. See Figure 1 through Figure 32.
entire CC-100 operations and maintenance manual. Get familiar with
the machine's parts.
TO PREVENT SERIOUS INJURY DO NOT OPERATE SAW WITHOUTPROPER TRAINING AND.
TO PREVENT SERIOUS INJURY DO NOT OPERATE SAW WITHOUTPROPER TRAINING AND.
TO PREVENT SERIOUS INJURY DO NOT OPERATE SAW WITHOUT PROPER
4.0
UNDERSTANDING OF THE OWNERS MANUAL
TRAINING AND. UNDERSTANDING OF THE OWNERS MANUAL
WHEN OPERATING THIS MACHINE
SERIOUS INJURY DO NOT OPERATE SAW WITHOUTPROPER TRAINING AND.
UNDERSTANDING OF THE OWNERS MANUAL
WHEN OPERATING THIS MACHINE
Read and understand
operator's manual before
Keep all guards
using this machine.
Failure to follow operating
in place
Instructions could result
in injury or damage to
equipment.
ALWAYS WEAR SAFETY APPROVED
ALWAYS WEAR SAFETY APPROVED
HEARING PROTECTION
WARNING
Flying debris
EYE OR FACE PROTECTION
PROTECTIVE HELMET
and loud noise
PROTECTIVE GLASSES OR FULL FACE PROTECTION
hazards. Wear
ear and eye
protection
WEAR HAND PROTECTION
WARNING: Improperly maintaining the JS including the Honda engine or failing to correct a problem before
operation could cause a malfunction resulting in a serious injury. Always perform a pre-operation inspection before
each operation and correct any problem. See Honda Engines Owner's Manual.
ng the JS including the Honda engine or failing to correct a problem before
5.2
Check the condition of the Honda engine. See the section titled "Before operation - is your
ion resulting in a serious injury. Always perform a pre-operation inspection before
engine ready to go?" in the Honda Engines Owner's Manual.
oblem. See Honda Engines Owner's Manual.
WARNING: Improperly maintaining the CC-100 including the Honda
engine or failing to correct a problem before operation could cause a
of the Honda engine. See the section titled "Before operation - is your
he Honda Engines Owner's Manual.
malfunction resulting in a serious injury. Always perform a pre-opera-
mproperly maintaining the JS including the Honda engine or failing to correct a problem before
ld cause a malfunction resulting in a serious injury. Always perform a pre-operation inspection before
tion inspection before each operation and correct any problem.
n and correct any problem. See Honda Engines Owner's Manual.
See Honda Engines Owner's Manual.
WARNING: Exhaust gas from gasoline engines contains dangerous carbon monoxide. Breathing it can cause
Check the condition of the Honda engine. See the section titled "Before operation - is your
unconsciousness and even kill you. Always operate gasoline engine machines in a well-ventilated area. Do not
soline engines contains dangerous carbon monoxide. Breathing it can cause
5.2
Check the condition of the Honda engine. See the section
operate in areas where exhaust fumes could accumulate without wearing appropriate respiratory protection.
ne ready to go?" in the Honda Engines Owner's Manual.
ou. Always operate gasoline engine machines in a well-ventilated area. Do not
titled "Before operation - is your engine ready to go?" in the
Avoid injury.
fumes could accumulate without wearing appropriate respiratory protection.
Consult your employer and OSHA regarding use of appropriate respirator for dangerous carbon monoxide
HA regarding use of appropriate respirator for dangerous carbon monoxide
gases. See Figure 7.
Honda Engines Owner's Manual.
Do NOT operate with
guard removed.
Replace guard before
operating machine.
xhaust gas from gasoline engines contains dangerous carbon monoxide. Breathing it can cause
E E n n g g i i n n e e e e x x h h a a u u s s t t c c o o n n t t a a i i n n s s
ess and even kill you. Always operate gasoline engine machines in a well-ventilated area. Do not
p p o o i i s s o o n n o o u u s s c c a a r r b b o o n n
m m o o n n o o x x i i d d e e g g a a s s . . Breathing
eas where exhaust fumes could accumulate without wearing appropriate respiratory protection.
it could cause death.
employer and OSHA regarding use of appropriate respirator for dangerous carbon monoxide
Operate machine in well
Rotating blade
gure 7.
ventilated area.
hazard.
Do NOT operate with
n n i i n n g g l l a a b b e e l l - - e e n n g g i i n n e e e e x x h h a a u u s s t t c c o o n n t t a a i i n n s s c c a a r r b b o o n n m m o o n n o o x x i i d d e e g g a a s s
guard up.
R R e e a a d d a a n n d d u u n n d d e e r r s s t t a a n n d d
o o p p e e r r a a t t o o r r ' ' s s m m a a n n u u a a l l b b e e f f o o r r e e
u u s s i i n n g g t t h h i i s s m m a a c c h h i i n n e e . .
F F a a i i l l u u r r e e t t o o f f o o l l l l o o w w o o p p e e r r a a t t i i n n g g
i i n n s s t t r r u u c c t t i i o o n n s s c c o o u u l l d d r r e e s s u u l l t t i i n n
i i n n j j u u r r y y o o r r d d a a m m a a g g e e t t o o
e e q q u u i i p p m m e e n n t t . .
Avoid injury.
Do NOT operate with
guard removed.
Replace guard before
UNDERSTANDING OF THE OWNERS MANUAL
operating machine.
WHEN OPERATING THIS MACHINE
Rules for safer operation
WHEN OPERATING THIS MACHINE
ALWAYS WEAR SAFETY APPROVED
Use only diamond blades (steel
HEARING PROTECTION
Wear Head Protec-
centered diamond cutting-off
wheels) with this machine. RPM
EYE OR FACE PROTECTION
tion, breathing pro-
rating on blade must exceed
PROTECTIVE HELMET
machine max rpm rating. The use
This product can expose you to chemicals, including NICKEL. When used, serviced, cleaned, or maintained equipment could generate particulates
tection, and the use
PROTECTIVE GLASSES OR FULL FACE PROTECTION
of any other blade could result in
that contain chemicals, including silica. These chemicals are known to the state of California to cause cancer and birth defects or other
death or serious injury.
of hearing protection
reproductive harm. For more information, visit
is mandatory
HEARING PROTECTION
EYE OR FACE PROTECTION
WEAR HAND PROTECTION
Wear hand
PROTECTIVE HELMET
5400 MAX. RPM
PROTECTIVE GLASSES OR FULL FACE PROTECTION
protection
5.5
C1 hazard Communication Sywems. L L L L C C
WEAR HAND PROTECTION
To avoid injury:
Always inspect saw
blades before use.
Replace all cracked or damaged
blades.
E E n n g g i i n n e e e e x x h h a a u u s s t t c c o o n n t t a a i i n n s s
Surface Prep
p p o o i i s s o o n n o o u u s s c c a a r r b b o o n n
m m o o n n o o x x i i d d e e g g a a s s . . Breathing
Division
it could cause death.
Operate machine in well
ventilated area.
1 1 1 1
using this machine.
Failure to follow operating
Instructions could result
in injury or damage to
equipment.
WARNING
AVOID STATIC ELECTRICITY RISK WHEN FUELING
WARNING: Ultra-Low Sulfur Diesel (ULSD) poses a greater static ignition
hazard. Consult with your fuel or fuel system supplier to ensure the deliv-
ery system is in compliance with fueling standards for proper grounding
and bonding practices. Maintaining a discharge strap must be connect-
ed to any U.S.SAWS vacuum at all times when equipment is being used.
5 5 . . 3 3
Observe the condition of your work environment. Walk over area work area and look for ha
sure the work environment is safe and meets all safe-working conditions discussed in sectio
for safer operation.
5 5 . . 4 4
Obtain MATERIAL SAFETY DATA SHEET (MSDS) for all work surface materials. This include
all coatings, adhesives, tile and crack filling materials, etc. Do not attempt to cut, clean out, o
material without MSDS information. Consult MSDS sheet for health hazards information. Be
some materials are explosive as a dust
WARNING: Exhaust gas from gasoline engines contains dangerous
To avoid injury:
carbon monoxide. Breathing it can cause unconsciousness and even kill
Always inspect saw
you. Always operate gasoline engine machines in a well-ventilated area.
blades before use.
Do not operate in areas where exhaust fumes could accumulate without
wearing appropriate respiratory protection. Consult your employer and
Replace all cracked or damaged
WARNING: The JS SERIES SAWS maximum blade operating speed is 5400 rpm as labeled on the
OSHA regarding use of appropriate respirator for dangerous carbon
blades.
Use only dry cut diamond blades rated higher than 5400 rpm safe operating speed. Do not use
monoxide gases. See Figure 7.
for less than 5400 rpm. Do not use a blade that is not a dry cut diamond blade. Using a non dry cut d
or a blade rated below 5400 rpm could result in severe blade failure, personal injury or death. See
Figure 9. Never cut material for which the blade was not designed. Check blade manufacturer's
Rotating blade
material to be cut. Never operate a blade in the wrong rotation direction. Verify blade direction w
hazard.
blades. The JS is designed to cut in a straight line. Never attempt to cut any pattern or follow any join
Do NOT operate with
straight line.
guard up.
Keep hands and feet
away.
Figure 2 - Warning label - engine exhaust contains carbon monoxide gas
5.3
Observe the condition of your work environment. Walk over
area work area and look for hazards. Make sure the work environment is
www.P65Warnings.ca.gov
safe and meets all safe-working conditions discussed in section 4, Rules
for safer operation.
5.4
Obtain SAFETY DATA SHEET (SDS) for all work surface materi-
als. This includes primers, all coatings, adhesives, tile and crack filling
F F i i g g u u r r e e 8 8 - - M M a a x x r r p p m m l l a a b b e e l l - - m m a a x x i i m m u u m m b b l l a a d d e e s s p p e e e e d d
materials, etc. Do not attempt to cut, clean out, or remove material
without SDS information. Consult SDS sheet for health hazards informa-
Choose the proper dry cut diamond blade for the application, speed and material to be
tion. Be aware that some materials are explosive as a dust
Figure 9.
M M O O - - 7 7 4 4 6 6 - - 0 0 2 2 4 4 1 1
F F i i g g u u r r e e 9 9 - - W W a a r r n n i i n n g g l l a a b b e e l l - - u u s s e e o o n n l l y y d d i i a a m m o o n n d d b b l l a a d d e e s s
Clearly mark all intended cut areas with straight paint or chalk lines.
5 5 . . 5 5
Verify that the lever is disengaged or released, and the Honda engine switch and fuel v
5 5 . . 6 6
in the OFF position. Make sure blade is completely stopped.
Engine exhaust
contains poisonous
c c a a r r b b o o n n m m o o n n o o x x i i d d e e g g a a s s . .
Breathing it could cause
death.
wheels) with this machine. RPM
rating on blade must exceed
machine max rpm rating. The use
of any other blade could result in
death or serious injury.
5400 MAX. RPM
C1 hazard Communication Sywems. L L L L C C
M M O O - - 7 7 4 4 6 6 - - 0 0 2 2 4 4 1 1
Wear proper electrostatic
grounding equipment at all
times. Static discharge during
fueling can cause explosion
Engine exhaust contains poi-
Engine exhaust
sonous carbon monoxide gas.
contains poisonous
Breathing it could cause death.
c c a a r r b b o o n n m m o o n n o o x x i i d d e e g g a a s s . .
Breathing it could cause
Operate machine in well venti-
death.
Operate machine in well
lated area.
ventilated area.
5 5 4 4 0 0 0 0 M M A A X X . . R R P P M M
U U s s e e o o n n l l y y d d i i a a m m o o n n d d b b l l a a d d e e s s ( ( s s t t e e e e l l
c c e e n n t t e e r r e e d d d d i i a a m m o o n n d d c c u u t t t t i i n n g g - - o o f f f f
w w h h e e e e l l s s ) ) w w i i t t h h t t h h i i s s m m a a c c h h i i n n e e . . R R P P M M
r r a a t t i i n n g g o o n n b b l l a a d d e e m m u u s s t t e e x x c c e e e e d d m m a a c c h h i i n n e e
m m a a x x r r p p m m r r a a t t i i n n g g . . T T h h e e u u s s e e o o f f a a n n y y o o t t h h e e r r
b b l l a a d d e e c c o o u u l l d d r r e e s s u u l l t t i i n n d d e e a a t t h h o o r r s s e e r r i i o o u u s s
i i n n j j u u r r y y . .
Figure 3 - Warning label - use only diamond blades
P: 877-817- 6687 F: 813-621-7125
Visit us at www.ussaws.com
sales@ussaws.com
6
Advertisement
