Table of Contents
Advertisement
Quick Links
U.S.SAWS MARK III
OPERATING MANUAL
TO PREVENT SERIOUS INJURY DO NOT OPERATE SAW WITHOUTPROPER TRAINING AND.
Copyright 2020, by U.S.SAWS . All rights reserved. This work may not be reproduced or disseminated in whole or in part by any
Notice of Copyright Protection
UNDERSTANDING OF THE OWNERS MANUAL
WHEN OPERATING THIS MACHINE
means without the prior written permission of U.S.SAWS
Surface Prep
ALWAYS WEAR SAFETY APPROVED
Division
HEARING PROTECTION
P: 877-817- 6687 F: 813-621-7125
Visit us at www.ussaws.com
sales@ussaws.com
U.S. English
08-31-2020
Advertisement
Table of Contents
Related Manuals for U.S.SAWS Mark III Dust Buggy
Summary of Contents for U.S.SAWS Mark III Dust Buggy
- Page 1 Notice of Copyright Protection UNDERSTANDING OF THE OWNERS MANUAL Copyright 2020, by U.S.SAWS . All rights reserved. This work may not be reproduced or disseminated in whole or in part by any WHEN OPERATING THIS MACHINE means without the prior written permission of U.S.SAWS...
-
Page 2: Introduction And Specifications
& maintenance of the U.S.SAWS MARK III Machine & to instruct you in safety practices for dealing with these conditions. Keep all manuals provided with your SPECIFICATIONS machine in a safe place at all times. -
Page 3: Symbols And Decals
U.S.SAWS MARK III behind machine. You must clearly understand the written instructions supplied by U.S.SAWS, be trained - including actual operation - & know Rules for safer operation ules for safer operation the safety rules & regulations for the job site. It is a safety practice to point out &... -
Page 4: Safety Instructions
Do not touch the muffler while it is hot. Let the engine cool maintenance training from a U.S. SAWS representative or from an autho- before storing indoors. Do not place flammable objects close to the engine. rized distributor for U.S.SAWS. 4.15 AVOID CONTACT WITH HOT BLADE AND BLADE GUARD. - Page 5 S A F E T Y I N S T R U C T I O N S 4.24 STORE IDLE EQUIPMENT. 4.38 WHEN REPLACING A PART, USE THE SAME TYPE The machine, blades and tools should be stored in a dry and secure loca- AND QUALITY.
-
Page 6: Pre-Operation Check List
Never operate a blade in the wrong rotation direction. Verify blade direction when changing blades. The U.S.SAWS MARK III i s designed 5 5 4 4 0 0 0 0 M M A A X X . . R R P P M M to cut in a straight line. - Page 7 P R E-O P E R AT I O N C H E C K L I S T Rules for safer operation Remove bolt in the blade guard holding bracket. Hold the blade guard firmly and raise guard up into the holding bracket. Reinsert bolt in Read and understand Use only diamond blades (steel the blade guard holding bracket and tighten nut.
- Page 8 P R E-O P E R AT I O N C H E C K L I S T Read and understand Use only diamond blades (steel operator's manual before centered diamond cutting-off using this machine. wheels) with this machine. RPM 5.13 Check for missing or loose bolts.
-
Page 9: O P E R At I O N & Pa R T S
O P E R AT I O N & PA R T S OPERATIONS CLEANING OUT EXISTING JOINTS: Follow all pre-operating instructions in section 5.0. The machine should be unplugged from electricity before start- ing this operation. WARNING: Never attempt to start the engine with the diamond blade inserted in a joint or previous cut. - Page 10 O P E R AT I O N & PA R T S LINING UP THE BLADE WITH THE JOINT/POINTER ADJUSTMENT MKIII CAST DUST BUGGY HANDLE ASSEMBLY: 6.16 Open Joint: With an un-filled control joint where it only needs to be cleaned of debris, it is better to line the pointer up with the left edge of the joint so that the pointer wheel rides along on the surface of the floor.
- Page 11 O P E R AT I O N & PA R T S 6.19 MARK III SERIES SAWS Parts Breakdown Reference Number Reference Number Part Number Part Number SX13711 SX13750 US32606 SX13740 SX13730 See Expanded View US31158, Washer US31337, Nut US30152 SX13751 SX113742 See Expanded View...
- Page 12 O P E R AT I O N & PA R T S Reference Number Part Number SX13743 US31063-11, Washer US31127-10 US31102-1 Reference Number Part Number US23154 SX65020 SX50501 PDC-SPA4 Reference Number Part Number SX13740 See Expanded View US31063-11, Nut US31056-11 SX13739 SX13738 SX13737...
- Page 13 O P E R AT I O N & PA R T S Reference Number Part Number SX13735 SX13734 SX13736 US31060-5 Spring US31339-10 Reference Number Part Number US67112 US60223 US67111 US67114 Reference Number Part Number US24600-33 *Comes as part of SXW24230 US31102-1 US67116 US32409...
- Page 14 O P E R AT I O N & PA R T S Reference Number Part Number SX13735 SX13734 SX13736 US31060-5 Spring US31339-10 Reference Number Part Number US67112 US60223 US67111 US67114 Reference Number Part Number US24600-33 *Comes as part of SXW24230 US31102-1 US67116 US32409...
- Page 15 O P E R AT I O N & PA R T S Reference Number Part Number US31053-13 US32235 US31053-14 US30176-1 Reference Number Part Number US31102-1, Washer US31321, Nut US3110-1 US31102-1, Washer US31321, Nut US3110-1 US13572 US13572-1C US31117-1, Nut US31110-1 SX13561-7 US31102-1, Washer US31321, Nut US3110-1...
-
Page 16: Related Products
R E L AT E D P R O D U C T S General Joint Cleanout / Concrete Cutting DCB08095UD 8 X .095 X 5/8-7/8 Supreme Grade Dry Cut Blade DCB08125UD 8 X .125 X 5/8-7/8 Supreme Grade Dry Cut Blade DCB08250UD 8 X .250 X 5/8-7/8 Supreme Grade Dry Cut Blade Polyurea / Joint Filler Removal APB08095D 8 X .095 X 5/8-7/8 TIGERTOOTH Diamond Grit Blade... -
Page 17: Warranty And Service
Warranty This document is to be used as a guide in determining warranty policies and procedures for U.S.SAWS and its U.S.SAWS products. It is to be used in determining whether a warranty is justified and as a procedural guide in completing a U.S.SAWS warranty claim form. - Page 18 FILL OUT THE ATTACHED CARD COMPLETELY AND ACCURATELY. WARRANTY REGISTRATION CARD IMPORTANT! To ensure that your U.S.SAWS machine is covered under warranty, please fill in the following information and mail or fax it to U.S.SAWS, 3702 W. Central Ave. Santa Ana, CA 92704, Fax No. 714-434-7299...