Page 1 2 0 2 0 O W N E R ’ S M A N U A L...
Page 2 This manual illustrates and describes the operation VEHICLES SOLD IN CANADA of features and equipment that are either standard or With respect to any Vehicles Sold in Canada, the name FCA US LLC shall be deemed to be deleted and the name optional on this vehicle.
Page 3 Mobile radio equipment with output power greater than INSTALLATION OF RADIO TRANSMITTING normal may require special precautions. EQUIPMENT All installations should be checked for possible interfer- Special design considerations are incorporated into this ence between the communications equipment and the vehicle’s electronic system to provide immunity to radio frequency signals.
Page 4: Table Of Contents
TABLE OF CONTENTS INTRODUCTION ....................................7 GETTING TO KNOW YOUR VEHICLE ............................9 GETTING TO KNOW YOUR INSTRUMENT PANEL ........................48 SAFETY ........................................69 STARTING AND OPERATING ..............................106 IN CASE OF EMERGENCY ................................128 SERVICING AND MAINTENANCE .............................153 TECHNICAL SPECIFICATIONS ..............................200 MULTIMEDIA ....................................207 CUSTOMER ASSISTANCE ................................210 INDEX ........................................214...
Page 5 INTRODUCTION  STEERING WHEEL ............20 Tilt/Telescoping Steering Column ......20   INTRODUCTION ..............7  MIRRORS ................20  HOW TO USE THIS MANUAL.......... 7 Automatic Dimming Mirror With Rear View Camera  Essential Information ............7 Display ................20  Symbols................7 Outside Mirrors .............21 ...
Page 6  DECKLID ................40  ONBOARD DIAGNOSTIC SYSTEM — OBD II .....66 To Open The Decklid ...........40 Onboard Diagnostic System (OBD II)   To Close The Decklid ............42 Cybersecurity ..............67   INTERNAL EQUIPMENT ..........43  EMISSIONS INSPECTION AND MAINTENANCE Storage................43 PROGRAMS .................67 ...
Page 7 STARTING AND OPERATING Fault Indication ............121  General Warnings ............121   STARTING THE ENGINE ..........106  PARKVIEW REAR BACK UP CAMERA ......122 Automatic Transmission ..........106  ADDING FUEL/SMART FUEL ........123  Normal Starting ............106  TRAILER TOWING ............125  Cold Weather Operation ..........107 ...
Page 8  IF YOUR ENGINE OVERHEATS ........149  RAISING THE VEHICLE ..........177  TOWING A DISABLED VEHICLE ........149  TIRES...................177 Front Tow Eye Usage..........149 Tire Safety Information..........177    FIRE EXTINGUISHER — IF EQUIPPED.......152 Tires — General Information ........185  ...
Page 9 Fuel System Cautions..........203  Alfa Romeo Customer Center........211 Carbon Monoxide Warnings ........204   Alfa Romeo Customer Care (Canada) ......211  FLUID CAPACITIES ............204  Customer Assistance For The Hearing Or Speech  FLUIDS AND LUBRICANTS ..........205  Impaired (TDD/TTY) ..........211 Engine ................205...
Page 10: Introduction
INTRODUCTION tion, that may or may not be applicable to your vehicle, will INTRODUCTION be identified with the wording "If Equipped". All data Dear Customer, contained in this publication are intended to help you use your vehicle in the best possible way. FCA US LLC aims at a Congratulations on selecting your new vehicle.
Page 11: Warnings And Cautions
8 INTRODUCTION component. Refer to “Warning Lights and Messages” in VEHICLE MODIFICATIONS/ALTERATIONS “Getting To Know Your Instrument Panel” for further infor- mation on the symbols used in your vehicle. WARNING! Any modifications or alterations to this vehicle could WARNINGS AND CAUTIONS seriously affect its roadworthiness and safety and may This Owner’s Manual contains WARNINGS against oper- lead to a collision resulting in serious injury or death.
Page 12: Getting To Know Your Vehicle
GETTING TO KNOW YOUR VEHICLE KEYS To Unlock The Doors Push and release the unlock button on the key fob to unlock Key Fob the doors. The parking lights and turn signal lights will flash The key fob contains an integrated mechanical key. To use to acknowledge the signal, and the illuminated entry system the mechanical key, simply push the key release button.
Page 13 10 GETTING TO KNOW YOUR VEHICLE When the doors are locked from outside the vehicle (using the key fob), the indicator above the door lock button will illuminate for a few seconds and then start flashing (deter- rent function). Battery Replacement Procedure 1 —...
Page 14 GETTING TO KNOW YOUR VEHICLE Replace the key fob battery with the following procedure: General Information 1. Push release button and move the mechanical key to The following regulatory statement applies to all Radio opening position. Frequency (RF) devices equipped in this vehicle: 2.
Page 15: Ignition Switch
12 GETTING TO KNOW YOUR VEHICLE NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. IGNITION SWITCH Ignition Key Removal 1. Press the brake pedal and place the transmission into FIRST (1) or REVERSE (R) gear by selecting/pushing the buttons on the console.
Page 16: Key-In-Ignition Reminder
GETTING TO KNOW YOUR VEHICLE SENTRY KEY WARNING! (Continued) The Sentry Key Immobilizer System prevents unauthorized • Allowing children to be in a vehicle unattended is vehicle operation by disabling the engine. The system does dangerous for a number of reasons. A child or others not need to be armed or activated.
Page 17: Replacement Keys
14 GETTING TO KNOW YOUR VEHICLE 2. l'utilisateur de l'appareil doit accepter tout brouillage Replacement Keys radioélectrique subi, même si le brouillage est susceptible NOTE: d'en compromettre le fonctionnement. • Only keys that have been programmed to the vehicle elec- La operación de este equipo está...
Page 18: To Arm The System
GETTING TO KNOW YOUR VEHICLE • Cutting of the battery leads If, after the alarm is armed, a second visual signal emits via the vehicle security light in the instrument panel, wait about • Anomalous lifting/tilting of the car four seconds and deactivate the alarm by pushing the lock Operation of the alarm is indicated by an acoustic and visual button.
Page 19: Doors
16 GETTING TO KNOW YOUR VEHICLE Disarming NOTE: In the absence of electrical power supply (blown fuse, To completely disable the alarm (e.g. during a lengthy period battery disconnected, etc.), it is still possible to lock the doors of vehicle inactivity), lock the vehicle by turning the metal manually.
Page 20: Emergency Door Locking Device
GETTING TO KNOW YOUR VEHICLE Unlocking Doors From The Outside 2. Push the unlock button on the key fob or the door locking/unlocking LED indicator button on the dash- Push the unlock button on the key fob or turn the mechanical board.
Page 21: Seats
18 GETTING TO KNOW YOUR VEHICLE To restore the starting condition of the door locks (only if Manual Front Seats battery charge is restored), proceed as follows: Forward And Rearward Adjustment 1. Push the unlock button on the key fob. The adjusting bar is at the front of the driver seat, near the 2.
Page 22: Head Restraints
GETTING TO KNOW YOUR VEHICLE Seat Height Adjustment WARNING! In order to achieve the ideal driving position, the height of • Adjusting a seat while driving may be dangerous. the seats can also be adjusted. Tools are required to make this Moving a seat while driving could result in loss of height adjustment.
Page 23: Steering Wheel
20 GETTING TO KNOW YOUR VEHICLE To unlock the steering column, push the lever downward WARNING! (Continued) (toward the floor). To tilt the steering column, move the • Be certain that the seatback is securely locked into posi- steering wheel upward or downward as desired. To tion.
Page 24: Outside Mirrors
GETTING TO KNOW YOUR VEHICLE When the vehicle is placed into REVERSE, a video display Outside Mirrors within the mirror illuminates to display the image generated To receive maximum benefit, adjust the outside mirrors to by the rear view camera located on the trunk lid below the center on the adjacent lane of traffic and a slight overlap of brake light.
Page 25: Heated Mirrors
22 GETTING TO KNOW YOUR VEHICLE Power Mirrors Folding Mirrors The power mirror controls are located on the center console. The exterior mirrors are hinged to allow the mirror to pivot forward or rearward to help avoid damage. The mirror has three detent positions: full forward, full rearward and normal.
Page 26: Exterior Lights
GETTING TO KNOW YOUR VEHICLE EXTERIOR LIGHTS Headlights Rotate the end of the multifunction lever upward to the first Multifunction Lever detent for headlight operation. The multifunction lever, located on the left side of the steering wheel, controls the operation of the headlights, headlight high beams, lane change assist and turn signals.
Page 27: High Beams
24 GETTING TO KNOW YOUR VEHICLE Remove the key or place the ignition in the STOP (OFF/ High Beams LOCK) position, and pull the multifunction lever toward the With the low beams activated, pull the multifunction lever steering wheel within two minutes. Each time the lever is towards the steering wheel to turn on the high beams.
Page 28: Interior Lights
GETTING TO KNOW YOUR VEHICLE INTERIOR LIGHTS Interior Light Timing (Center Position) There are four different modes of operation that can be acti- Interior Light vated in this position: The interior light is located in the headliner in between the •...
Page 29: Windshield Wipers And Washers
26 GETTING TO KNOW YOUR VEHICLE Dimmer Controls The dimmer controls are located on the left side of the instru- ment panel below the instrument cluster. Windshield Wiper/Washer Lever Windshield Wiper Operation Rotate the end of the lever upward, to the first detent past the Dimmer Controls intermittent settings for low-speed wiper operation.
Page 30: Climate Controls
GETTING TO KNOW YOUR VEHICLE Windshield Washers Mist To use the washer, pull the lever toward you and hold while Use the Mist feature when weather conditions make occa- spray is desired. If the lever is pulled while in the delay sional usage of the wipers necessary.
Page 31: Climate Controls Overview
28 GETTING TO KNOW YOUR VEHICLE Climate Controls Overview Climate Controls...
Page 32 GETTING TO KNOW YOUR VEHICLE Climate Control Descriptions Icon Description A/C Button Push and release to change the current setting, the indicator illuminates when A/C is on. Performing this function again will cause the A/C operation to switch into manual mode and the A/C indicator will turn off.
Page 33 30 GETTING TO KNOW YOUR VEHICLE Icon Description Temperature Control Knob Temperature control is used to regulate the temperature of the air forced through the climate system. The temperature can be selected using the temperature control knob on the faceplate. The temperature increases as you turn the temperature control knob clockwise.
Page 34: Climate Control Functions
GETTING TO KNOW YOUR VEHICLE Icon Description Mix Mode Mix Mode Air is directed through the floor, defrost, and side window demister outlets. This setting works best in cold or snowy conditions that require extra heat to the windshield. This setting is good for maintaining comfort while reducing moisture on the windshield.
Page 35 32 GETTING TO KNOW YOUR VEHICLE Window Demisting Internal Air Recirculation Activation In the event of considerable external moisture and/or rain Slide the Recirculation knob to the position. and/or large differences in temperature inside and outside It is advisable to turn the Internal Air Recirculation on while the passenger compartment, perform the following preven- the vehicle is at a standstill, or in tunnels, to prevent the tive window demisting procedure:...
Page 36: Windows
GETTING TO KNOW YOUR VEHICLE Cooling Adjustment System Maintenance Proceed as follows: In Winter, the Climate Control system must be turned on at least once a month for about 10 minutes. Have the system 1. Move the Recirculation Control to inspected at an authorized dealer before the Summer.
Page 37 34 GETTING TO KNOW YOUR VEHICLE window control units replaced), the automatic operation of the windows must be restored. The restoration procedure must be performed as described below with the doors closed: 1. Completely open the driver's door window keeping the operating button pushed for at least three seconds after the (lower) end of travel position is reached.
Page 38: Removable Soft Top
GETTING TO KNOW YOUR VEHICLE REMOVABLE SOFT TOP Your vehicle is equipped with a removable soft top. Removing The Soft Top To remove the soft top, proceed as follows: 1. Turn the front locking handles located near the sun visors to the left one quarter turn.
Page 39: Installing The Soft Top
36 GETTING TO KNOW YOUR VEHICLE 4. Remove the soft top with both sides rolled up. 2. Unfold the top and be sure to position the front edge (red strip) under the spoiler of the vehicle. 5. Place the pin buffer over the front locking handle pins to prevent damage to the soft top during storage.
Page 40 GETTING TO KNOW YOUR VEHICLE 3. As the side beam is unrolled, engage the two fixed locating pins (1 front, 1 rear) into their retainers. Unlocking The Side Beam 5. Rotate down the side beam. Locating Pin Locations 1 — Front Locating Pin Location 2 —...
Page 41 38 GETTING TO KNOW YOUR VEHICLE 6. Release the handles and complete the rotation to lock the 7. Check to make sure that the handles are locked in place. soft top. Handles In Locked Position Soft Top In Locking Position 8.
Page 42 GETTING TO KNOW YOUR VEHICLE 9. Insert the front locking handles located near the sun • With the top open and the vehicle traveling, the speech visors in the proper holes and turn them to the right one recognition system along with the dial number command quarter turn.
Page 43: Decklid
40 GETTING TO KNOW YOUR VEHICLE • Never use alcohol, petroleum products, chemical prod- CAUTION! (Continued) ucts, detergents, stain removers, wax, solvents, and “wash • During normal vehicle operation, the luggage compart- and polish” products. ment (located rear of the engine) can reach tempera- •...
Page 44 GETTING TO KNOW YOUR VEHICLE 3. Move to the rear of the vehicle and lift the decklid. 5. Place the decklid prop rod in the decklid slot to secure the decklid in the open position. Decklid Lift Point Location Decklid Prop Rod Slot 4.
Page 45: To Close The Decklid
42 GETTING TO KNOW YOUR VEHICLE NOTE: WARNING! (Continued) Always check that the decklid is closed correctly to prevent • Access the luggage compartment only with the vehicle it from opening while the vehicle is traveling. stationary. Before exiting the vehicle, you should always place the vehicle into FIRST gear or REVERSE, WARNING! apply the parking brake, and remove the key from the...
Page 46: Internal Equipment
GETTING TO KNOW YOUR VEHICLE INTERNAL EQUIPMENT Console Storage — If Equipped The cargo pouch storage area is located between the driver Storage and passenger seats. Seatback Storage Located in the back of both the driver and passenger front seats are pockets that can be used for storage. Cargo Pouch Storage Location Driver’s Side Seatback Storage...
Page 47 44 GETTING TO KNOW YOUR VEHICLE Rear Compartment Storage WARNING! Do not allow children to have access to rear storage CAUTION! compartment. Always close the decklid when your • To prevent possible damage, do not slam the decklid to vehicle is unattended. Once in the rear storage close it.
Page 48: Cupholder
GETTING TO KNOW YOUR VEHICLE Cupholder WARNING! A cupholder is located in the rear of the center console. • The maximum load limit for the luggage compartment, in addition to the kits provided, is 33.1 lbs. (15kg). Do not exceed the maximum permitted load in the luggage compartment.
Page 49: Power Outlets
46 GETTING TO KNOW YOUR VEHICLE Power Outlets Your vehicle is equipped with a 12 Volt (13 Amp) power outlet that can be used to power cellular phones, small elec- tronics and other low powered electrical accessories. Power Outlet Fuse Location (F86) WARNING! To avoid serious injury or death: •...
Page 50 GETTING TO KNOW YOUR VEHICLE CAUTION! CAUTION! (Continued) • Many accessories that can be plugged in draw power • Do not exceed the maximum power of 180 Watts (15 Amps) from the vehicle's battery, even when not in use (i.e., at 12 Volts.
Page 51: Getting To Know Your Instrument Panel
GETTING TO KNOW YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER Instrument Cluster...
Page 52: Instrument Cluster Descriptions
GETTING TO KNOW YOUR INSTRUMENT PANEL 3. Speedometer Instrument Cluster Descriptions 1. Temperature Gauge • Indicates vehicle speed. • The temperature gauge shows engine coolant tempera- 4. Fuel Gauge ture. Any reading within the normal range indicates that • The digital display shows the amount of fuel in the the engine cooling system is operating satisfactorily.
Page 53: Instrument Cluster Display
50 GETTING TO KNOW YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DISPLAY Location And Controls Your vehicle is equipped with an instrument cluster display, which offers useful information to the driver. With the igni- tion in the STOP (OFF/LOCK) position (and the key removed, for vehicles with mechanical key), opening/ closing of a door will activate the display for viewing, and display the total miles or kilometers in the odometer.
Page 54: Change Engine Oil Indicator System
GETTING TO KNOW YOUR INSTRUMENT PANEL • SET/BACK Arrow Button The system allows the driver to select information by pushing the following buttons mounted on the instrument Push and release the SET/BACK arrow button to access/ panel to the left of the steering column: select the information screens or submenu screens of a main menu item.
Page 55: Instrument Cluster Display Programmable Menu
52 GETTING TO KNOW YOUR INSTRUMENT PANEL Selecting An Option Of The Main Menu Without Instrument Cluster Display Programmable Menu Submenu: The menu comprises a series of functions arranged in a cycle. Push the up and down arrow buttons to access the different 1.
Page 56 GETTING TO KNOW YOUR INSTRUMENT PANEL To cancel the setting, proceed as follows: Speed Buzzer (Speed Limit) 1. Briefly push the SET/BACK button, “On” will display. With this function, it is possible to set the vehicle speed limit (mph or km/h) to immediately alert the driver when the set 2.
Page 57 54 GETTING TO KNOW YOUR INSTRUMENT PANEL • When accessing the “Mode” submenu, briefly push the Set Time SET/BACK button. The previously set display format This function may be used to set the clock through two will flash on the display. submenu items: “Time”...
Page 58 GETTING TO KNOW YOUR INSTRUMENT PANEL NOTE: Units (Set Units) The setting will increase or decrease by one unit each time This function may be used to set the measurement unit in the up or down arrow button is pushed. Push and hold the three submenus: “Distance,”...
Page 59 56 GETTING TO KNOW YOUR INSTRUMENT PANEL 3. Briefly push the SET/BACK button to go back to the If the distance unit set is “km,” the fuel economy unit will be displayed in either km/l or l/100km. menu screen, or push and hold the SET/BACK button (approximately one second) to go back to the main screen 1.
Page 60: Values Displayed
GETTING TO KNOW YOUR INSTRUMENT PANEL 2. Briefly push the SET/BACK button to go back to the 3. Push and release the up or down arrow button for setting. menu screen or hold the button down to go back to the 4.
Page 61: Trip Computer
58 GETTING TO KNOW YOUR INSTRUMENT PANEL Average Fuel Consumption This value shows the approximate average consumption since the last reset. Travel Distance This value shows the distance covered since the last reset. Current Fuel Consumption This indicates the fuel consumption. The value is constantly updated.
Page 62: Trip Button
GETTING TO KNOW YOUR INSTRUMENT PANEL • Current Fuel Consumption Trip Button • Average Speed The TRIP/RESET button, located on the right steering column stalk, can be used to display and to reset the trip • Travel Time values. “Trip B” can be used to display the figures relating to: •...
Page 63: Start Of Trip Procedure
60 GETTING TO KNOW YOUR INSTRUMENT PANEL concerning Trip A or Trip B, only the information associated Red Warning Lights with Trip A or Trip B functions will be reset. Brake Warning Light Start Of Trip Procedure This warning light monitors various brake func- With the ignition on, push and hold the TRIP button for over tions, including brake fluid level and parking brake two seconds to reset trip information.
Page 64 GETTING TO KNOW YOUR INSTRUMENT PANEL NOTE: Oil Pressure Warning Light The light may flash momentarily during sharp cornering This warning light will illuminate to indicate low maneuvers, which change fluid level conditions. The vehicle engine oil pressure. If the light turns on while should have service performed, and the brake fluid level driving, stop the vehicle, shut off the engine as soon checked.
Page 65 62 GETTING TO KNOW YOUR INSTRUMENT PANEL Air Bag Warning Light Battery Charge Warning Light — If Equipped This light will turn on for four to eight seconds as a This light illuminates when the battery is not bulb check when the ignition is placed in the ON/ charging properly.
Page 66: Yellow Warning Lights
GETTING TO KNOW YOUR INSTRUMENT PANEL tires is significantly under-inflated. Accordingly, when the Yellow Warning Lights low tire pressure telltale illuminates, you should stop and Tire Pressure Monitoring System (TPMS) Warning Light check your tires as soon as possible, and inflate them to the proper pressure.
Page 67 64 GETTING TO KNOW YOUR INSTRUMENT PANEL Electronic Stability Control (ESC) Warning Light — If CAUTION! Equipped The TPMS has been optimized for the original The Electronic Stability Control (ESC) Indicator equipment tires and wheels. TPMS pressures and Light in the instrument cluster will come on when warning have been established for the tire size equipped the ignition is placed in the ON/RUN or MAR/ON/ on your vehicle.
Page 68 GETTING TO KNOW YOUR INSTRUMENT PANEL Electronic Stability Control (ESC) OFF Warning Light — WARNING! If Equipped A malfunctioning catalytic converter, as referenced This warning light indicates the Electronic Stability above, can reach higher temperatures than in normal Control (ESC) is off. operating conditions.
Page 69: Green Indicator Lights
66 GETTING TO KNOW YOUR INSTRUMENT PANEL beams. Pull the multifunction lever rearward (toward the Green Indicator Lights rear of the vehicle) to turn off the high beams. If the high Turn Signal Indicator Lights beams are off, pull the lever toward you for a temporary high beam on, “flash to pass”...
Page 70: Onboard Diagnostic System (Obd Ii) Cybersecurity
GETTING TO KNOW YOUR INSTRUMENT PANEL Onboard Diagnostic System (OBD II) Cybersecurity EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS Your vehicle is required to have an Onboard Diagnostic system (OBD II) and a connection port to allow access to In some localities, it may be a legal requirement to pass an information related to the performance of your emissions inspection of your vehicle's emissions control system.
Page 71 68 GETTING TO KNOW YOUR INSTRUMENT PANEL If your OBD II system is not ready, you should see an autho- 3. Approximately 15 seconds later, one of two things will happen: rized dealer or repair facility. If your vehicle was recently serviced or had a battery failure or replacement, you may •...
Page 72: Safety
SAFETY SAFETY FEATURES WARNING! (Continued) • For maximum efficiency of the braking system, a Four-Wheel Anti-Lock Brake System (ABS) bedding-in period of about 311 miles (500 km) is The Four-Wheel Anti-Lock Brake System (ABS) is designed required: during this period it is advisable to avoid to aid the driver in maintaining vehicle control under sharp, repeated and prolonged braking.
Page 73: Electronic Stability Control (Esc) System
70 SAFETY When you are in a severe braking condition involving the WARNING! use of the ABS, you will experience some pedal drop as the • Electronic Stability Control (ESC) cannot prevent the vehicle comes to a stop. This is the result of the system natural laws of physics from acting on the vehicle, nor reverting to the base brake system.
Page 74 SAFETY The ESC system uses sensors installed on the vehicle to System Intervention determine the trajectory that the driver intends to follow and This is indicated by the flashing of the warning light on the compares it with the vehicles effective trajectory. When the instrument panel to inform the driver that the vehicle is in real trajectory deviates from the desired trajectory, the ESC critical stability and grip conditions.
Page 75 72 SAFETY This is an integral part of the ESC system and automatically AntiSlip Regulation System (ASR) operates in the event of one or both drive wheels slipping, WARNING! loss of grip on wet roads (hydroplaning), and acceleration on slippery, snowy, or icy roads, etc. •...
Page 76 SAFETY When setting off, the ESC system control unit maintains the WARNING! (Continued) braking pressure on the wheels until the engine torque • The HBA system cannot prevent accidents, including necessary for starting is reached, or in any case for a those due to excessive speed on corners, driving on maximum of two seconds, allowing your right foot to be low-grip surfaces or aquaplaning.
Page 77: Auxiliary Driving Systems
74 SAFETY maximum inflation pressure molded into the tire sidewall. Electronic Q2 System (E-Q2) Refer to “Tires” in “Servicing And Maintenance” for infor- The E-Q2 system intervenes during acceleration on corners, mation on how to properly inflate the vehicle’s tires. The tire braking the inner drive wheel and thus increasing the trac- pressure will also increase as the vehicle is driven - this is tion of the outer wheel (which bears more of the vehicle’s...
Page 78 SAFETY NOTE: vehicle may cause the tire pressure to rise to approximately 27 psi (186 kPa), but the TPMS Warning Light will still be on. • The TPMS is not intended to replace normal tire care and In this situation, the TPMS Warning Light will turn off only maintenance, or to provide warning of a tire failure or after the tires are inflated to the vehicle’s recommended cold condition.
Page 79 76 SAFETY NOTE: The TPMS Warning Light will turn off when the fault condi- It is particularly important for you to check the tire pressure tion no longer exists. A system fault can occur with any of the in all of the tires on your vehicle regularly and to maintain following scenarios: the proper pressure.
Page 80: Occupant Restraint Systems
SAFETY 4. This occurs for each subsequent ignition key cycle, a 2. l'utilisateur de l'appareil doit accepter tout brouillage chime will sound and the TPMS Warning Light will flash radioélectrique subi, même si le brouillage est susceptible on and off for 75 seconds and then remain on solid. d'en compromettre le fonctionnement.
Page 81: Important Safety Precautions
78 SAFETY 7. The driver and front passenger seats should be moved Important Safety Precautions back as far as practical to allow the front air bags room to Please pay close attention to the information in this section. inflate. It tells you how to use your restraint system properly, to 8.
Page 82: Seat Belt Systems
SAFETY outboard front seat belts are buckled. The outboard front Seat Belt Systems passenger seat BeltAlert is not active when an outboard front Buckle up even though you are an excellent driver, even on passenger seat is unoccupied. short trips. Someone on the road may be a poor driver and BeltAlert Warning Sequence could cause a collision that includes you.
Page 83 80 SAFETY is folded flat (if equipped). It is recommended that pets be WARNING! restrained in the rear seat (if equipped) in pet harnesses or • Relying on the air bags alone could lead to more severe pet carriers that are secured by seat belts, and cargo is prop- injuries in a collision.
Page 84 SAFETY WARNING! (Continued) WARNING! (Continued) • Two people should never be belted into a single seat • A seat belt that is too loose will not protect you prop- belt. People belted together can crash into one another erly. In a sudden stop, you could move too far forward, in a collision, hurting one another badly.
Page 85 82 SAFETY Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is above the back of the front seat, and next to your arm in the rear seat (for vehicles equipped with a rear seat).
Page 86 SAFETY 3. Slide the latch plate upward over the folded webbing. The folded webbing must enter the slot at the top of the latch plate. 4. Continue to slide the latch plate up until it clears the folded webbing and the seat belt is no longer twisted. Seat Belts And Pregnant Women Positioning The Lap Belt 5.
Page 87 84 SAFETY Vehicle Seat Belt” under the “Child Restraints” section of this Seat Belt Pretensioner manual. The figure below illustrates the locking feature for The front outboard seat belt system is equipped with preten- each seating position. sioning devices that are designed to remove slack from the seat belt in the event of a collision.
Page 88: Supplemental Restraint Systems (Srs)
SAFETY How To Disengage The Automatic Locking Mode has a seat belt with this feature. Children 12 years old and under should always be properly restrained in the rear seat Unbuckle the combination lap/shoulder belt and allow it to of a vehicle with a rear seat. retract completely to disengage the Automatic Locking Mode and activate the vehicle sensitive (emergency) locking WARNING!
Page 89 86 SAFETY The air bag system must be ready to protect you in a colli- switch is in the STOP/OFF/LOCK position the air bag sion. The Occupant Restraint Controller (ORC) monitors the system is not on and the air bags will not inflate. internal circuits and interconnecting wiring associated with The ORC contains a backup power supply system that may the electrical Air Bag System Components.
Page 90 SAFETY NOTE: If the speedometer, tachometer, or any engine related gauges are not working, the Occupant Restraint Controller (ORC) may also be disabled. In this condition the air bags may not be ready to inflate for your protection. Have an authorized dealer service the air bag system immediately.
Page 91 88 SAFETY WARNING! WARNING! (Continued) • No objects should be placed over or near the air bag on • Never install a rear-facing child restraint in the front the instrument panel or steering wheel because any seat of a vehicle. Only use a rear-facing child restraint such objects could cause harm if the vehicle is in a colli- in the rear seat.
Page 92 SAFETY On the other hand, depending on the type and location of WARNING! impact, front air bags may deploy in crashes with little • Do not drill, cut, or tamper with the knee impact vehicle front-end damage but that produce a severe initial bolsters in any way.
Page 93 90 SAFETY The SABICs deploy upward, covering the side windows. An WARNING! inflating SABIC pushes the outside edge of the trim out of Do not mount equipment, or stack luggage or other cargo the way and covers the window. The SABICs inflate with up high enough to block the deployment of the SABICs.
Page 94 SAFETY Side Air Bags are a supplement to the seat belt restraint WARNING! (Continued) system. Side Air Bags deploy in less time than it takes to • Relying on the Side Air Bags alone could lead to more blink your eyes. severe injuries in a collision.
Page 95 92 SAFETY • Supplemental Side Air Bags • As the air bags deflate, you may see some smoke-like parti- cles. The particles are a normal by-product of the process • Supplemental Knee Air Bags that generates the non-toxic gas used for air bag inflation. •...
Page 96 SAFETY • Horn Enhanced Accident Response System • Front wiper In the event of an impact, if the communication network • Headlamp washer pump remains intact, and the power remains intact, depending on the nature of the event, the Occupant Restraint Controller NOTE: (ORC) will determine whether to have the Enhanced Acci- After an accident, remember to cycle the ignition to the STOP...
Page 97 94 SAFETY Customer Will See Customer Action NOTE: Each step MUST BE held for at least two seconds 1. Turn ignition STOP/OFF/LOCK. (Turn Signal Switch Must be placed in Neutral State). Right turn light BLINKS. 2. Turn ignition MAR/ACC/ON/RUN. Left turn light is OFF. Right turn light is ON SOLID.
Page 98 SAFETY Customer Will See Customer Action NOTE: Each step MUST BE held for at least two seconds 12. Turn ignition MAR/ACC/ON/RUN. (Entire sequence needs to be completed within one minute or sequence will System is now reset and the engine may be started. need to be repeated).
Page 99: Child Restraints
96 SAFETY record data related to vehicle dynamics and safety systems Child Restraints for a short period of time, typically 30 seconds or less. The Everyone in your vehicle needs to be buckled up at all times, EDR in this vehicle is designed to record such data as: including babies and children.
Page 100 SAFETY NOTE: Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards. • For additional information, refer http:// You should also make sure that you can install it in the www.nhtsa.gov/parents-and-caregivers call: vehicle where you will use it.
Page 101 98 SAFETY Infant And Child Restraints Older Children And Child Restraints Safety experts recommend that children ride rear-facing in Children who are two years old or who have outgrown their the vehicle until they are two years old or until they reach rear-facing convertible child seat can ride forward-facing in either the height or weight limit of their rear-facing child the vehicle.
Page 102 SAFETY 4. Is the lap part of the belt as low as possible, touching the WARNING! (Continued) child’s thighs and not the stomach? • After a child restraint is installed in the vehicle, do not 5. Can the child stay seated like this for the whole trip? move the vehicle seat forward or rearward because it can loosen the child restraint attachments.
Page 103 100 SAFETY Please see the table below and the following sections for WARNING! (Continued) more information. • Follow the child restraint manufacturer’s directions exactly when installing an infant or child restraint. Lap/Shoulder Belt Systems For Installing Child Restraints In This Vehicle The seat belt in the passenger seating position is equipped with a Switchable Automatic Locking Retractor (ALR) that is designed to keep the lap portion of the seat belt tight around...
Page 104 SAFETY into the retractor. As the webbing retracts, you will hear Installing A Child Restraint With A Switchable Automatic a clicking sound. This means the seat belt is now in the Locking Retractor (ALR) Automatic Locking mode. Child restraint systems are designed to be secured in vehicle seats by lap belts or the lap belt portion of a lap/shoulder 6.
Page 105: Transporting Pets
102 SAFETY 3. Attach the tether strap hook of the child restraint to the Installing Child Restraints Using The Top Tether top tether anchorage as shown in the diagram. Anchorage: Always use the tether anchor when using the seat belt to 4.
Page 106: Exhaust Gas
SAFETY WARNING! (Continued) WARNING! (Continued) • It is extremely dangerous to ride in a cargo area, inside • If it is necessary to sit in a parked vehicle with the or outside of a vehicle. In a collision, people riding in engine running, adjust your heating or cooling controls these areas are more likely to be seriously injured or to force outside air into the vehicle.
Page 107 104 SAFETY Front seat belt assemblies must be replaced after a collision. is securely attached using the floor mat fasteners so it cannot Rear seat belt assemblies must be replaced after a collision if slip out of position and interfere with the accelerator, brake they have been damaged (i.e., bent retractor, torn webbing, or clutch pedals or impair safe operation of your vehicle in etc.).
Page 108: Periodic Safety Checks You Should Make Outside The Vehicle
SAFETY WARNING! (Continued) WARNING! (Continued) • ONLY use the driver’s side floor mat on the driver’s • It is recommended to only use mild soap and water to side floor area. To check for interference, with the clean your floor mats. After cleaning, always check vehicle properly parked with the engine off, fully your floor mat has been properly installed and is depress the accelerator, the brake, and the clutch pedal...
Page 109: Starting And Operating
STARTING AND OPERATING sion control panel (or the "+" steering wheel stalk) to engage STARTING THE ENGINE FIRST (1st) gear or the R button to engage REVERSE (R). Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. When FIRST (1st) gear is engaged, the system sets itself to AUTO mode.
Page 110: Cold Weather Operation
STARTING AND OPERATING Cold Weather Operation After Starting Your engine is designed to operate at temperatures as low as The idle speed is controlled automatically, and it will 0°F (-18°C). decrease as the engine warms up. Turbo Charger “Cool Down” CAUTION! This vehicle is equipped with an after-run pump to cool the Use of the recommended oil and adhering to the...
Page 111: Parking Brake
108 STARTING AND OPERATING Additionally, for the first 200 miles (300 km), following these few simple guidelines is all that is necessary for a good break-in. • Avoid very aggressive driving. • Avoid driving at a constant speed, either fast or slow, for long periods.
Page 112: Six-Speed Alfa Twin Clutch Transmission
STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) • Do not leave the key fob in or near the vehicle or in a • Unintended movement of a vehicle could injure those location accessible to children. A child could operate in or near the vehicle. As with all vehicles, you should power windows, other controls, or move the vehicle.
Page 113 110 STARTING AND OPERATING MANUAL Mode When the key is turned to the ON position, the current trans- mission gear will be displayed in the instrument cluster, In this operating mode, the driver is responsible for choosing along with the "AUTO" indicator. This indicates the trans- the best gear to engage, depending on the vehicle’s operating mission is in Automatic mode.
Page 114 STARTING AND OPERATING AUTO Mode • If the brake pedal is not depressed (and the vehicle is stationary for a period of time), the transmission will auto- In AUTO mode the transmission shifts gears automatically matically engage NEUTRAL (N). depending on vehicle speed, engine RPM, and accelerator •...
Page 115 112 STARTING AND OPERATING Neutral (N) Acoustic Signal Use this range when the vehicle is standing for prolonged If the vehicle is stationary with the engine running and periods with the engine running. Always apply the parking FIRST (1) or REVERSE (R) engaged, the system activates an brake if you must exit the vehicle.
Page 116: Alfa Dna System (Dynamic Vehicle Control System)
STARTING AND OPERATING General Notes ALFA DNA SYSTEM (DYNAMIC VEHICLE CONTROL SYSTEM) When the vehicle is stopped and in gear, always keep the brake pedal pressed until you decide to set off, then release This vehicle is equipped with an “Alfa DNA” system lever the brake and accelerate gradually.
Page 117: Driving Modes
114 STARTING AND OPERATING Electronic Q2 system: Driving Modes The system increases vehicle stability while accelerating on The Alfa DNA system lever will always return to the center bends, improving the agility of the vehicle. position after use. Engine And Gearbox/Transmission: The selected driving mode is indicated by the corresponding LED switching in the panel and by an indication on the The system adjusts the transmission shift calibration for...
Page 118 STARTING AND OPERATING Electronic Stability Control (ESC) and Anti-Slip Regula- The LED corresponding to Dynamic mode will light up and tion (ASR) systems: the Dynamic mode activation indication will appear on the display. These systems are deactivated in order to ensure the fullest sensation of sport, leaving the driver in full control of the Natural Mode vehicle.
Page 119: System Failure
116 STARTING AND OPERATING Electronic Q2 System: Launch Control The system is deactivated. The Launch Control strategy permits high-performance acceleration from a standstill. Engine And Gearbox/Transmission: This strategy can be activated with vehicle at a standstill, Standard response shifting. Race mode selected and FIRST (1st) gear engaged. Deactivation The sequence of operations to perform is as follows: To deactivate All Weather mode and return to Natural...
Page 120: Speed Control - If Equipped
STARTING AND OPERATING NOTE: WARNING! In order to ensure proper operation, the Speed Control Launch Control is intended for off-highway or off-road system has been designed to shut down if multiple speed use only and should not be used on any public control functions are operated at the same time.
Page 121: To Activate
118 STARTING AND OPERATING To Activate To Vary The Speed Setting To Increase Speed Rotate the end of the Speed Control lever upward to the first detent, indicated by the speed control icon, to activate the When the Speed Control is set, you can increase speed by Speed Control.
Page 122: To Accelerate For Passing
STARTING AND OPERATING To Decrease Speed lever, and release. Resume can be used at any speed above 18 mph (30 km/h). When the Speed Control is set, you can decrease speed by tapping the speed control lever down (-). To Deactivate The speed decrement shown is dependent on the speed of A soft tap on the brake pedal, pushing the CANCEL/ U.S.
Page 123: Acoustic Signal
120 STARTING AND OPERATING Acoustic Signal Indications On Display — If Equipped When REVERSE gear is engaged, and there is an obstacle When the sensors are activated, the parking sensor display behind the vehicle, an acoustic signal is emitted which varies screen appears in the instrument cluster.
Page 124: Activation/Deactivation
STARTING AND OPERATING The signal is similar for obstacles in the rear left or right area. Some conditions may influence the performance of the The arc that corresponds to the position of the obstacle will parking sensors: flash. The color on the instrument cluster display depends on •...
Page 125: Parkview Rear Back Up Camera
122 STARTING AND OPERATING pear. The ParkView camera is located on the trunk lid below WARNING! the brake light. Drivers must be careful when backing up even when When the vehicle is shifted out of REVERSE, the camera using the Parking Sensor system. Always check carefully image will continue to be displayed for up to 10 seconds after behind your vehicle, and be sure to check for shifting out of REVERSE.
Page 126: Adding Fuel/Smart Fuel
STARTING AND OPERATING ADDING FUEL/SMART FUEL WARNING! Drivers must be careful when backing up even when NOTE: using the ParkView Rear Back Up Camera. Always check • The "Smart Fuel" is a device placed on the top of the filler carefully behind your vehicle, and be sure to check for pipe;...
Page 127 124 STARTING AND OPERATING 2. There is no fuel filler cap. A flap door inside the pipe seals A funnel is provided to open the flapper door to allow emer- the system. gency refueling with a gas can. 1. Retrieve the appropriate funnel from the storage area in the luggage compartment.
Page 128: Trailer Towing
STARTING AND OPERATING in NEUTRAL. This vehicle may also be towed on a flatbed or WARNING! vehicle trailer, provided all four wheels are OFF the ground. • Never have any smoking materials lit in or near the vehicle when the fuel door is open or the tank is being CAUTION! filled.
Page 129: Driving Through Water
126 STARTING AND OPERATING • Maintain sufficient distance between your vehicle and the Acceleration vehicle in front of you to avoid a collision in a sudden stop. Rapid acceleration on snow covered, wet, or other slippery surfaces may cause the driving wheels to pull erratically to Your vehicle may be equipped with a Limited Slip Differen- the right or left.
Page 130 STARTING AND OPERATING WARNING! CAUTION! (Continued) • Driving through standing water limits your vehicle’s • Driving through standing water may cause damage to traction capabilities. Do not exceed 5 mph (8 km/h) your vehicle’s drivetrain components. Always inspect when driving through standing water. your vehicle’s fluids (i.e., engine oil, transmission, axle, etc.) for signs of contamination (i.e., fluid that is milky •...
Page 131: In Case Of Emergency
IN CASE OF EMERGENCY ROADSIDE ASSISTANCE HAZARD WARNING FLASHER To contact Alfa Romeo Emergency Roadside Assistance Dial The Hazard Warning flasher switch is located on the center toll-free 1–844–253–2872 Residents console. 1–844–953–3232 for Canadian Residents Push the switch to turn on the Hazard Warning •...
Page 132: Replacing Exterior Bulbs
IN CASE OF EMERGENCY Exterior Bulbs Bulb Name Bulb Number Font and Rear Side Lights Dipped/Main Beam Headlights (Versions With Bi-Halogen HIR2 Headlights) — If Equipped Dipped/Main Beam Headlights (Versions With Bi-Xenon D5S (See Authorized Dealer) Headlights) — If Equipped Dipped/Main Beam Headlights (Versions With Bi-Led LED (See Authorized Dealer) Headlights) —...
Page 133 130 IN CASE OF EMERGENCY Side Lights/Daytime Running Lights (DRL) Front Light Clusters The front head lamp contains bulbs for the parking lights/ These are LEDs. For the replacement, contact an authorized daytime running lights (DRL), low beam headlights, high dealer.
Page 134 IN CASE OF EMERGENCY 3. Remove protective cover from headlamp assembly. Bulb Holder 1 — Electrical Connector Protective Cover 2 — Bulb Holder 4. Remove the electric connector (1) and then rotate the bulb holder (2) clockwise and remove it. 5.
Page 135 132 IN CASE OF EMERGENCY Low/High Beam HID & LED Headlights For the replacement, contact an authorized dealer. Direction Indicators Front: 1. Turn the steering wheel completely. 2. Open the protective flap by rotating the screw. Protective Cover 4. Rotate the bulb holder counterclockwise and remove it. 5.
Page 136 IN CASE OF EMERGENCY Side: Front Side Marker 1. Compress the retaining clip, then pull the side marker To change the bulb, proceed as follows: assembly outwards. 1. Turn the front wheels to gain access and then remove the fasteners from the inner wheel liner. Side Direction Indicator 1 —...
Page 137 134 IN CASE OF EMERGENCY 2. Fold back wheel liner door to access bulb housing. Rear Light Clusters These contain the bulbs for the side lights, direction indica- tors and brake lights. Direction Indicators To change the bulb, proceed as follows: 1.
Page 138 IN CASE OF EMERGENCY 2. Remove the second protective cap and insert a hand Reversing Light inside the opening. WARNING! The reverse lights are located close to the exhaust pipes; take the utmost care not to get burnt during the bulb replacement.
Page 139 136 IN CASE OF EMERGENCY License Plate Lights To replace the bulbs, proceed as follows: 1. Compress the retaining clip, then pull the license plate light cluster out. Reversing Light Bulb Holder Third Brake Lights These are LEDs. For the replacement, contact an authorized dealer.
Page 140 IN CASE OF EMERGENCY 2. Turn bulb holder counterclockwise, remove bulb and Roof Light replace it. To change the bulb, proceed as follows: 1. Remove roof light working at the points indicated by the arrows in the graphic. 1 — Bulb Holder 2 —...
Page 141 138 IN CASE OF EMERGENCY 2. Open protective flap (2) and replace bulb (1), releasing it Luggage Compartment Roof Light from the side contacts. Make sure that the new bulb is To replace the bulb, proceed as follows: correctly secured between the contacts. 1.
Page 142: Fuses
IN CASE OF EMERGENCY Also, please be aware that when using power outlets for FUSES extended periods of time with the engine off may result in WARNING! vehicle battery discharge. • When replacing a blown fuse, always use an appro- priate replacement fuse with the same amp rating as the original fuse.
Page 143: Engine Compartment Fuses
140 IN CASE OF EMERGENCY The ID number of the electrical component corresponding to Engine Compartment Fuses each fuse can be found on the back of the cover. The engine compartment fuse box is located on the left side of the engine compartment, next to the battery. To access the fuses, remove screws, and then remove the cover.
Page 144 IN CASE OF EMERGENCY Cavity Maxi Fuse Mini Fuse Description 20 Amp Yellow – Blower Motor – 5 Amp Tan Headlight Beam Switch – If Equipped – 10 Amp Red Horn – 20 Amp Yellow Powertrain – 15 Amp Blue Alfa Twin Clutch Transmission –...
Page 145: Dashboard Fuse Box
142 IN CASE OF EMERGENCY forward passenger floor. Remove the six screws and the Dashboard Fuse Box forward floor pan to access the BCM. The dashboard fuse box is part of the Body Control Module (BCM) and is located on the passenger side under the Cavity Vehicle Fuse Number Mini Fuse...
Page 146: Tire Service Kit Storage Location
IN CASE OF EMERGENCY Tire Service Kit Storage Location WARNING! (Continued) The Tire Service Kit is located in the rear storage area under • If the tire has any sidewall damage. the decklid. • If the tire has any damage from driving with extremely low tire pressure.
Page 147 144 IN CASE OF EMERGENCY WARNING! (Continued) • Tire Service Kit Sealant solution contains latex. In case of an allergic reaction or rash, consult a physician immediately. Keep Tire Service Kit out of reach of chil- dren. If swallowed, rinse mouth immediately with plenty of water and drink plenty of water.
Page 148 IN CASE OF EMERGENCY 4. Apply the parking brake. (4.8 Bar). The pressure gauge will decrease quickly from approximately 70 psi (4.8 Bar) to the actual tire pressure 5. Remove speed limit sticker off of the sealant cartridge when the sealant cartridge is empty. and place it inside the vehicle visually available for the driver to see.
Page 149: Tire Service Kit Usage Precautions
146 IN CASE OF EMERGENCY • When the Tire Service Kit sealant is in a liquid form, clean WARNING! water, and a damp cloth will remove the material from the Tire Service Kit is not a permanent flat tire repair. Have vehicle or tire and wheel components.
Page 150: Preparations For Jump Start
IN CASE OF EMERGENCY 4. If using another vehicle to jump start the battery, park the Preparations For Jump Start vehicle within the jumper cable’s reach, apply the The battery in your vehicle is located on the left side of the parking brake and make sure the ignition is OFF.
Page 151 148 IN CASE OF EMERGENCY WARNING! Do not connect the jumper cable to the negative (-) post of the discharged battery. The resulting electrical spark could cause the battery to explode and could result in personal injury. Only use the specific ground point, do not use any other exposed metal parts.
Page 152: If Your Engine Overheats
IN CASE OF EMERGENCY CAUTION! WARNING! Accessories plugged into the vehicle power outlets draw You or others can be badly burned by hot engine coolant power from the vehicle’s battery, even when not in use (antifreeze) or steam from your radiator. If you see or (i.e., cellular devices, etc.).
Page 153 150 IN CASE OF EMERGENCY The front tow eye receptacle is located on the lower right side of the front fascia. Front Tow Eye Installed When using a tow eye, be sure to follow the “Tow Eye Usage Precautions” in this section. Tow Eye Receptacle Location To install the tow eye, thread the tow eye into the receptacle.
Page 154 IN CASE OF EMERGENCY Tow Eye Usage Precautions The transmission must be in NEUTRAL (N) when flat towing this vehicle. The ignition must be ON in order to place the transmission in NEUTRAL. Therefore, if the key is unavailable or the battery is discharged, this vehicle must be towed with all four wheels OFF the ground (using a vehicle trailer or flatbed truck).
Page 155: Fire Extinguisher - If Equipped
152 IN CASE OF EMERGENCY FIRE EXTINGUISHER — IF EQUIPPED ENHANCED ACCIDENT RESPONSE SYSTEM (EARS) The fire extinguisher is located under the dashboard in front This vehicle is equipped with an Enhanced Accident of the passenger side seat. Response System. Please refer to “Occupant Restraint Systems”...
Page 156: Servicing And Maintenance
SERVICING AND MAINTENANCE NOTE: SCHEDULED SERVICING The actual interval for changing the oil and replacing the Your vehicle is equipped with an automatic oil change indi- engine oil filter depends on the vehicle usage conditions and cator system. The oil change indicator system will remind is signaled by the warning light or message (if equipped) on you that it is time to take your vehicle in for scheduled main- the instrument panel or every 12 months.
Page 157: Maintenance Plan
154 SERVICING AND MAINTENANCE Once A Month Or Before A Long Trip/Periodic Checks Under any of the previous circumstances, the following checks need to be performed more frequently than indicated Every 600 miles (1,000 km) or before long trips, check and, if in the Maintenance Plan: necessary, top off the following: •...
Page 158 SERVICING AND MAINTENANCE NOTE: At Every Oil Change Interval As Indicated By Oil Using white lithium grease, lubricate the door hinge roller Change Indicator System: pivot joints twice a year to prevent premature wear. Inspect engine cooling system protection and hoses. Check and adjust hand brake.
Page 159 156 SERVICING AND MAINTENANCE Mileage or time passed (whichever comes first) Or Months: Or Kilometers: Check windshield/washer operation Check position/wear windshield blade Check cleanliness of hood and deck locks, well cleanliness lubrication associated linkages Visually inspect condition exterior bodywork, carbon monocoque, aerodynamic bottom, pipes and hoses (exhaust, fuel supply system, brakes), rubber...
Page 160 SERVICING AND MAINTENANCE Mileage or time passed (whichever comes first) Or Months: Or Kilometers: Check and top off, if required, fluid levels (engine coolant, brake/ hydraulic clutch fluid, windscreen washer fluid, battery fluid, etc) Visually inspect the condition of accessory drive belt(s) Check condition of timing belt Check handbrake lever travel and adjust, if necessary (or every...
Page 161 158 SERVICING AND MAINTENANCE Mileage or time passed (whichever comes first) Or Months: Or Kilometers: Change brake fluid every 24 months Replace air filter cartridge 1. Recommend using Midtronics tester to check charge status and, if necessary, recharge battery. 2. The spark plug change interval is mileage based only, yearly intervals do not apply. The following are essential to ensure correct opera- tion and prevent serious damage to the engine: •...
Page 162: Engine Compartment
SERVICING AND MAINTENANCE ENGINE COMPARTMENT 1750 Turbo Engine 1 — Fuse Box 4 — Engine Oil Dip Stick 2 — Battery 5 — Coolant Reservoir 3 — Engine Oil Fill Do not check oil level when the engine is warm. Checking Checking Oil Level engine oil level when the engine is warm will give you an To ensure proper engine lubrication, the engine oil must be...
Page 163: Adding Washer Solvent
160 SERVICING AND MAINTENANCE the dipstick. The safe range is indicated by a crosshatch zone. To check the windshield washer solvent level, proceed as Adding 1 quart of oil when the reading is at the low end of follows: the indicated range will result in the oil level at the full end 1.
Page 164 SERVICING AND MAINTENANCE 4. Leaving the plug close to the opening, put a finger on the 5. After the check, reinsert the plug with the control pipe in central hole in the plug and remove it: the level can be the initial position.
Page 165: Maintenance-Free Battery
162 SERVICING AND MAINTENANCE 5. Introduce the funnel and its extension pipe in the reser- Maintenance-Free Battery voir neck and top up. Your vehicle is equipped with a maintenance-free battery. You will never have to add water, nor is periodic mainte- nance required.
Page 166: Pressure Washing
SERVICING AND MAINTENANCE DEALER SERVICE CAUTION! The pages that follow contain the required maintenance • It is essential when replacing the cables on the battery services determined by the engineers who designed your that the positive cable is attached to the positive post vehicle.
Page 167: Engine Oil
164 SERVICING AND MAINTENANCE Engine Oil Materials Added To Engine Oil The manufacturer strongly recommends against the addi- Change Engine Oil tion of any additives (other than leak detection dyes) to the The oil change indicator system will remind you that it is engine oil.
Page 168: Engine Air Cleaner Filter
SERVICING AND MAINTENANCE To reassemble the cover back onto the engine, first make sure Engine Air Cleaner Filter it is properly aligned, the oil cap is centered, and that all four Refer to the “Maintenance Plan” in this section for the proper studs are lined up with their couplers.
Page 169: Body Lubrication
166 SERVICING AND MAINTENANCE When performing other underhood services, the hood latch, CAUTION! release mechanism and safety catch should be cleaned and Do not use chemical flushes in your air conditioning lubricated. system chemicals damage your The external lock cylinders should be lubricated twice a year, conditioning components.
Page 170 SERVICING AND MAINTENANCE 4. Lift the blade from the windshield and proceed with the Blade Lifting required operation. If it is necessary to lift the blade from the windshield (in the event of snow or blade replacement) proceed as directed: 5.
Page 171: Windshield Washer Nozzles
Should it be necessary to adjust Tips” in “Safety” for further information. them again, contact your authorized Alfa Romeo Dealer. • A hot exhaust system can start a fire if you park over If there is not a jet of fluid, first check that there is fluid in the materials that can burn.
Page 172: Cooling System
SERVICING AND MAINTENANCE To minimize the possibility of catalytic converter damage: CAUTION! • Do not shut off the engine or interrupt the ignition, when • The catalytic converter requires the use of unleaded the transmission is in gear and the vehicle is in motion. fuel only.
Page 173 170 SERVICING AND MAINTENANCE Selection Of Coolant WARNING! (Continued) Refer to “Fluids And Lubricants” in “Technical Specifica- • When working near the radiator cooling fan, discon- tions” for further information. nect the fan motor lead or turn the ignition switch to the OFF position.
Page 174 SERVICING AND MAINTENANCE NOTE: Adding Coolant • It is the owner's responsibility to maintain the proper level Your vehicle has been built with an improved engine coolant of protection against freezing according to the tempera- (OAT coolant conforming to MS.90032) that allows extended tures occurring in the area where the vehicle is operated.
Page 175 172 SERVICING AND MAINTENANCE As long as the engine operating temperature is satisfactory, WARNING! the coolant bottle need only be checked once a month. • Do not open hot engine cooling system. Never add When additional engine coolant (antifreeze) is needed to engine coolant (antifreeze) when the engine is over- maintain the proper level, it should be added to the coolant heated.
Page 176: Brake System
SERVICING AND MAINTENANCE • Maintain engine coolant (antifreeze) concentration at a Brake Master Cylinder minimum of 50% OAT coolant (conforming to MS.90032) The fluid level in the master cylinder should be checked and distilled water for proper corrosion protection of your when performing under hood services, or immediately if the engine which contains aluminum components.
Page 177 174 SERVICING AND MAINTENANCE CAUTION! WARNING! (Continued) Use of improper brake fluids will affect overall clutch • To avoid contamination from foreign matter or mois- system performance. Improper brake fluids may damage ture, use only new brake fluid or fluid that has been in the clutch system resulting in loss of clutch function and a tightly closed container.
Page 178 SERVICING AND MAINTENANCE To check the brake fluid level, proceed as follows: 2. Loosen the reservoir plug and introduce the funnel with the extension pipe in the reservoir inlet. 1. Loosen the two screws and remove the brake fluid protec- tion panel.
Page 179: Alfa Twin Clutch Transmission
176 SERVICING AND MAINTENANCE Alfa Twin Clutch Transmission CAUTION! Do not use chemical flushes in your transmission as the Selection Of Lubricant chemicals can damage your transmission components. It is important to use the proper transmission fluid to ensure Such damage is not covered by the New Vehicle Limited optimum transmission performance and life.
Page 180: Raising The Vehicle
SERVICING AND MAINTENANCE RAISING THE VEHICLE Tire Markings In the case where it is necessary to raise the vehicle, go to an authorized dealer or service station. TIRES Tire Safety Information Tire safety information will cover aspects of the following information: Tire Markings, Tire Identification Numbers, Tire Terminology and Definitions, Tire Pressures, and Tire Loading.
Page 181 178 SERVICING AND MAINTENANCE NOTE: same as for P-Metric tires except for the letters “LT” that are molded into the sidewall preceding the size designa- • P (Passenger) — Metric tire sizing is based on US design tion. Example: LT235/85R16. standards.
Page 182 SERVICING AND MAINTENANCE EXAMPLE: R = Construction code • "R" means radial construction, or • "D" means diagonal or bias construction 15, 16, 18 = Rim diameter in inches (in) Service Description: 95 = Load Index • A numerical code associated with the maximum load a tire can carry H = Speed Symbol •...
Page 183 180 SERVICING AND MAINTENANCE Tire Identification Number (TIN) The Tire Identification Number (TIN) may be found on one or both sides of the tire; however, the date code may only be on one side. Tires with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire.
Page 184 SERVICING AND MAINTENANCE Tire Terminology And Definitions Term Definition The vehicle B-Pillar is the structural member of the body located behind B-Pillar the front door. Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hours, or driven less than 1 mile Cold Tire Inflation Pressure (1.6 km) after sitting for a minimum of three hours.
Page 185 182 SERVICING AND MAINTENANCE This placard tells you important information about the: 1. Number of people that can be carried in the vehicle. 2. Total weight your vehicle can carry. 3. Tire size designed for your vehicle. 4. Cold tire inflation pressures for the front, rear, and spare tires.
Page 186 SERVICING AND MAINTENANCE Steps For Determining Correct Load Limit— Metric Example For Load Limit (1) Locate the statement “The combined weight of occu- For example, if “XXX” amount equals 635 kg and there pants and cargo should never exceed XXX kg or XXX lbs.” will be five 68 kg passengers in your vehicle, the amount on your vehicle's placard.
Page 187 184 SERVICING AND MAINTENANCE WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them.
Page 188: Tires - General Information
SERVICING AND MAINTENANCE Tires — General Information WARNING! (Continued) • Unequal tire pressures from one side of the vehicle to Tire Pressure the other can cause the vehicle to drift to the right or Proper tire inflation pressure is essential to the safe and satis- left.
Page 189 186 SERVICING AND MAINTENANCE Example: If garage temperature = 68°F (20°C) and the Tire Inflation Pressures outside temperature = 32°F (0°C) then the cold tire inflation The proper cold tire inflation pressure is listed on the driver's pressure should be increased by 3 psi (21 kPa), which equals side B-Pillar or rear edge of the driver's side door.
Page 190 SERVICING AND MAINTENANCE Flat mode. A Run Flat mode occurs when the tire inflation Radial Ply Tires pressure is of/or below 14 psi (96 kPa). Once a Run Flat tire WARNING! reaches the run flat mode it has limited driving capabilities and needs to be replaced immediately.
Page 191 188 SERVICING AND MAINTENANCE Tread Wear Indicators Life Of Tire Tread wear indicators are in the original equipment tires to The service life of a tire is dependent upon varying factors help you in determining when your tires should be replaced. including, but not limited to: •...
Page 192 SERVICING AND MAINTENANCE Replacement Tires WARNING! The tires on your new vehicle provide a balance of many • Do not use a tire, wheel size, load rating, or speed rating characteristics. They should be inspected regularly for wear other than that specified for your vehicle. Some combi- and correct cold tire inflation pressures.
Page 193: Tire Types
190 SERVICING AND MAINTENANCE Tire Types Snow Tires Some areas of the country require the use of snow tires All Season Tires — If Equipped during the Winter. Snow tires can be identified by a “moun- All Season tires provide traction for all seasons (Spring, tain/snowflake”...
Page 194 SERVICING AND MAINTENANCE Since this tire has limited tread life, the original equipment CAUTION! tire should be repaired (or replaced) and reinstalled on your Because of the reduced ground clearance, do not take vehicle at the first opportunity. your vehicle through an automatic car wash with a Do not install a wheel cover or attempt to mount a conven- compact or limited use temporary spare installed.
Page 195: Wheel And Wheel Trim Care
192 SERVICING AND MAINTENANCE Since this tire has limited tread life, the original equipment Limited Use Spare — If Equipped tire should be repaired (or replaced) and reinstalled on your The limited use spare tire is for temporary emergency use vehicle at the first opportunity.
Page 196: Tire Chains (Traction Devices)
SERVICING AND MAINTENANCE NOTE: Your wheels are susceptible to deterioration caused by salt, sodium chloride, magnesium chloride, calcium chloride, etc., If you intend parking or storing your vehicle for an extended and other road chemicals used to melt ice or control dust on period after cleaning the wheels with wheel cleaner, drive dirt roads.
Page 197: Tire Rotation Recommendations
Broken devices can cause serious damage. Stop the grip performance with little increase of wear. Alfa Romeo, in vehicle immediately if noise occurs that could indicate collaboration with Pirelli, developed a specific high perfor- device breakage.
Page 198: Traction Grades
SERVICING AND MAINTENANCE 100. The relative performance of tires depends upon the Sustained high temperature can cause the material of the actual conditions of their use, however, and may depart tire to degenerate and reduce tire life, and excessive significantly from the norm due to variations in driving temperature can lead to sudden tire failure.
Page 199: Bodywork
196 SERVICING AND MAINTENANCE BODYWORK Body And Underbody Maintenance Protection From Atmospheric Agents Cleaning Headlights Your vehicle is equipped with plastic headlights and fog Vehicle body care requirements vary according to lights that are lighter and less susceptible to stone breakage geographic locations and usage.
Page 200: Preserving The Bodywork
SERVICING AND MAINTENANCE Preserving The Bodywork CAUTION! (Continued) • Do not run this vehicle through an Automatic Car Wash Washing facility as extensive damage can result due to the • Wash your vehicle regularly. Always wash your vehicle in vehicle’s low ground clearance. the shade using Mopar Car Wash, or a mild car wash soap, and rinse the panels completely with clear water.
Page 201: Interiors
198 SERVICING AND MAINTENANCE INTERIORS WARNING! A frayed or torn belt could rip apart in a collision and Seats And Fabric Parts leave you with no protection. Inspect the belt system Use Mopar Total Clean to clean fabric upholstery and periodically, checking for cuts, frays, or loose parts.
Page 202: Leather Parts
SERVICING AND MAINTENANCE 1. Clean with a wet soft cloth. A mild soap solution may be CAUTION! used, but do not use high alcohol content or abrasive Do not use Alcohol and Alcohol-based and/or Ketone cleaners. If soap is used, wipe clean with a clean damp based cleaning products to clean leather upholstery, as cloth.
Page 203: Technical Specifications
TECHNICAL SPECIFICATIONS there will be some loss of overall braking effectiveness. You VEHICLE IDENTIFICATION NUMBER may notice increased pedal travel during application, greater The Vehicle Identification Number (VIN) is found on the left pedal force required to slow or stop, and potential activation front corner of the instrument panel, visible through the of the “Brake System Warning Light”.
Page 204 TECHNICAL SPECIFICATIONS Inspect the wheel mounting surface prior to mounting the tire and remove any corrosion or loose particles. Torque Patterns After 25 miles (40 km) check the lug nut/bolt torque to be sure that all the lug nuts/bolts are properly seated against Wheel Mounting Surface the wheel.
Page 205: Fuel Requirements - 1750 Turbo
202 TECHNICAL SPECIFICATIONS stability additives are recommended. Using gasolines that FUEL REQUIREMENTS — 1750 TURBO have these additives will help improve fuel economy, reduce The 1750 turbo engine is designed to meet all emis- emissions, and maintain vehicle performance. sions regulations and provide excellent fuel Designated TOP TIER Detergent Gasoline contains a economy performance...
Page 206: E-85 Usage In Non-Flex Fuel Vehicles
TECHNICAL SPECIFICATIONS Problems that result from using gasoline containing more the responsibility of the manufacturer and may void or not than 10% ethanol (E-10) or gasoline containing methanol are be covered under the New Vehicle Limited Warranty. not the responsibility of the manufacturer and may void or MMT In Gasoline not be covered under New Vehicle Limited Warranty.
Page 207: Carbon Monoxide Warnings
204 TECHNICAL SPECIFICATIONS Carbon Monoxide Warnings CAUTION! (Continued) • An out-of-tune engine or certain fuel or ignition WARNING! malfunctions can cause the catalytic converter to over- Carbon monoxide (CO) in exhaust gases is deadly. heat. If you notice a pungent burning odor or some Follow the precautions below to prevent carbon light smoke, your engine may be out of tune or monoxide poisoning:...
Page 208: Fluids And Lubricants
* The following are essential to ensure correct operation and cated Alfa Romeo Dealership. Refer to “Scheduled prevent serious damage to the engine: only use spark plugs Servicing” in “Servicing And Maintenance” for the required of the same make and type, which are specially certified for spark plug intervals.
Page 209: Chassis
206 TECHNICAL SPECIFICATIONS Chassis Component Fluid, Lubricant, or Genuine Part • Gearbox: Full synthetic 75W-85 manual transmission fluid meeting MS.90021 or FPW9.55550–MZ3 or the API GL4 specification. • Control System: Use only Mopar C Series DDCT SAE 75W Hydraulic Fluid or Alfa Twin Clutch Transmission equivalent.
Page 210: Multimedia
MULTIMEDIA CYBERSECURITY WARNING! Your vehicle may be a connected vehicle and may be • It is not possible to know or to predict all of the equipped with both wired and wireless networks. These possible outcomes if your vehicle’s systems are networks allow your vehicle to send and receive informa- breached.
Page 211: Radio System
208 MULTIMEDIA NOTE: Hi Fi System — If Equipped • FCA US LLC or your dealer may contact you directly The Hi Fi radio system consists of: regarding software updates. • Supply cables for radio, speakers, and antenna • To help further improve vehicle security and minimize the •...
Page 212: General Information
MULTIMEDIA La operación de este equipo está sujeta a las siguientes dos General Information condiciones: The following regulatory statement applies to all Radio 1. es posible que este equipo o dispositivo no cause interfer- Frequency (RF) devices equipped in this vehicle: encia perjudicial y This device complies with Part 15 of the FCC Rules and with 2.
Page 213: Customer Assistance
CUSTOMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR IF YOU NEED ASSISTANCE YOUR VEHICLE The manufacturer and its authorized dealers are vitally inter- ested in your satisfaction. We want you to be happy with our Prepare For The Appointment products and services. If you are having warranty work done, be sure to have the Warranty service must be done by an authorized dealer.
Page 214: Alfa Romeo Customer Center
Phone: 1-844-253-2872 turer's service contracts. If you purchased a manufacturer's service contract, you will receive Plan Provisions and an Alfa Romeo Customer Care (Canada) Owner Identification Card in the mail within three weeks of P.O. Box 1621 the vehicle delivery date. If you have any questions about the...
Page 215: Warranty Information
212 CUSTOMER ASSISTANCE We appreciate that you have made a major investment when REPORTING SAFETY DEFECTS you purchased the vehicle. An authorized dealer has also In The 50 United States And Washington, D.C. made a major investment in facilities, tools, and training to assure that you are absolutely delighted with the ownership If you believe that your vehicle has a defect that could experience.
Page 216: Publication Order Forms
CUSTOMER ASSISTANCE Owner's Manuals PUBLICATION ORDER FORMS To order the following manuals, you may use either the These Owner's Manuals have been prepared with the assis- tance of service and engineering specialists to acquaint you website or the phone numbers listed below. with specific FCA US LLC vehicles.
Page 217 INDEX Alterations/Modifications Adding Engine Coolant (Antifreeze) ........171 Vehicle..................8 Adding Fuel ................123 Antifreeze (Engine Coolant) ..........170, 204 Adding Washing Fluid ............160 Disposal ................172 Additives, Fuel ................202 Anti-Lock Brake System (ABS) ..........69 Air Bag..................87 Anti-Lock Warning Light............64 Air Bag Operation ..............88 Assistance Towing ..............128 Air Bag Warning Light............86 Automatic Transaxle..............12 Driver Knee Air Bag .............89...
Page 218 Coolant (Antifreeze) ............204, 205 Camera ..................122 Cooling Pressure Cap (Radiator Cap)........171 Camera, Rear ................122 Cooling System................169 Capacities, Antifreeze (Engine Coolant) ......204 Adding Coolant (Antifreeze)..........171 Capacities, Fluid..............204 Coolant Level ...............170, 172 Caps, Filler Disposal Of Used Coolant..........172 Oil (Engine) ..............159, 164 Drain, Flush, And Refill .............170 Radiator (Coolant Pressure) ..........171 Inspection ................172...
Page 219 Driver’s Seat Back Tilt ..............18 Oil Selection .................164 Overheating................149 Driving Starting..................106 Through Flowing, Rising, Or Shallow Standing Enhanced Accident Response Feature ......93, 152 Water..................126 Ethanol..................202 Euro Twin Clutch Transmission Electric Brake Control System..........70 Fluid Type ................176 Electric Remote Mirrors ............22 Exhaust Gas Cautions.............103, 204 Electrical Power Outlets............46 Exhaust System..............103, 168...
Page 220 Ethanol..................202 Ignition Key Removal...............12 Gasoline ................202 Immobilizer (Sentry Key)............13 Materials Added..............202 Inside Rearview Mirror ............20 Methanol................202 Instrument Cluster..............48, 66 Octane Rating ..............202 Instrument Panel Lens Cleaning...........198 Requirements...............202 Interior And Instrument Lights ..........25 Tank Capacity..............204 Interior Appearance Care ............198 Fueling ..................123 Interior Lights ................25 Fuses ..................139 Intermittent Wipers (Delay Wipers)........26...
Page 221 Bulb Replacement ...............128 Master Cylinder Cruise ..................66 Brakes..................173 Electronic Stability Program (ESP) Indicator ....62 Methanol...................202 Engine Temperature Warning..........62 Mirrors ..................20 Exterior ................23, 105 Electric Remote ..............22 Hazard Warning Flasher............128 Heated..................22 Interior ..................25 Outside................21, 22 Malfunction Indicator (Check Engine).......65 Rearview.................20 Park ................... 24, 66 Modifications/Alterations Passing ..................24 Vehicle..................8...
Page 222 Recommendation ............164, 204 Refrigerant................166 Viscosity ................164 Reminder, Seat Belt..............79 Onboard Diagnostic System............66 Remote Keyless Entry Operating Precautions..............66 Unlock The Doors..............9 Operator Manual Replacement Bulbs..............128 Owner's Manual ..............7, 213 Replacement Keys..............14 Outside Rearview Mirrors ............21 Replacement Tires..............189 Overheating, Engine...............149 Reporting Safety Defects............212 Owner’s Manual (Operator Manual) ........
Page 223 Rear Seat .................80 Steering ..................20 Reminder ................62, 79 Column Lock................20 Seat Belt Pretensioner ............84 Tilt Column ................20 Untwisting Procedure ............83 Wheel, Tilt ................20 Seat Belts Maintenance............198 Storage ................43, 195 Seats ....................18 Storage, Vehicle ...............195 Adjustment................18 Storing Your Vehicle...............195 Rear Folding................18 Supplemental Restraint System –...
Page 224 Replacement.................189 Rotation ................194 Vehicle Identification Number (VIN) ........200 Safety................177, 185 Vehicle Loading...............182 Sizes..................178 Vehicle Modifications/Alterations...........8 Snow Tires................190 Vehicle Security Alarm.............14 Spare Tires............190, 191, 192 Vehicle Storage ................195 Spinning................187 Tread Wear Indicators............188 Warning Flashers, Hazard .............128 Wheel Nut Torque ..............200 Warning Lights (Instrument Cluster Descriptions) .....65 To Open Deck Lid..............40 Warnings And Cautions ............8...
Page 228 ©2019 FCA US LLC. All Rights Reserved. ALFA ROMEO is a registered trademark of FCA Group Marketing S.p.A., used with permission. App Store is a registered trademark of Apple Inc. Google Play Store is a registered trademark of Google.. Printed in the U. S. A.

Alfa Romeo 4C Spider 2020 Owner's Manual

Introduction

Getting to Know Your Vehicle

Getting to Know Your Instrument Panel

Safety

7 Servicing and Maintenance

Technical Specifications

Multimedia

Customer Assistance

Quick Links

Related Manuals for Alfa Romeo 4C Spider 2020

Summary of Contents for Alfa Romeo 4C Spider 2020

Table of Contents