Advertisement
Part number SP1202
06-07 Subaru WRX 2.5L
04-07 Subaru STi 2.5L
1- 2 pc. Injen cold air intake (CA)
1- 2.75" Injen filter
1- 3" straight hose
1- 2 3/4" straight hose
2- Power-bands (.362) .048 (#4004)
2- Power-bands (.312) .040 (#4003)
1- M6 vibra-mount
1- M6 flange nut
1- fender washer
1- 12" vinyl trim flex-grip
1- 3 page instruction
Note:
Do to the sensitivity of the ECU, some
additional engine tuning maybe
required to correct short term fuel
.
and timing trims
Note: The installation of this air intake does require mechanical skills. Removal of the front bumper requires
loosening and removing several plastic plugs and screws that may be difficult. In addition to removing the
bumper, you may also have to remove the air resonator box, battery and tray when beginning this installation.
Injen strongly recommends that this system be installed by a professional mechanic.
MR
Patent Pending
Available in wrinkled Red
Congratulations! You have just purchased the best engineered,
dyno-proven cold air intake system available.
Report any defective or missing parts to the Authorized Injen
Technology dealer you purchased this product from.
(#1013)
Before installing any parts of this system, please read the instructions
thoroughly. If you have any questions regarding installation please
(#3044)
contact the dealer you purchased this product from.
(#3043)
Installation DOES require some mechanical skills. A qualified
mechanic is always recommended.
*Do not attempt to install the intake system while the engine is hot.
(#6020)
The installation may require removal of radiator fluid line that may
(#6002)
be hot.
(#6010)
Injen Technology offers a limited lifetime warranty to the original
(#6023)
purchaser against defects in materials and workmanship. Warranty
claims must be handled through the dealer from which the item was
purchased.
Injen Technology 244 Pioneer Place Pomona, CA 91768 USA
Note: This intake system was Dyno-tested with an Injen filter and
Injen parts. The use of any other filter or part will void the
warranty and CARB exemption number.
Parts and accessories are available on line at "Injenonline.com"
Technology, "The World's First Tuned Intake System!"
Optimum performance, Factory safe air/fuel ratio.
"An air intake evolution"
Please check the contents of this box immediately.
Please check the contents of this box immediately.
Process Developed and invented by Injen Technology.
Tri-step process with tuned adapter, calibrates the intake
for a desirable A/F ratio and ultimate power gains.
TPR magazine rates Injen #1 against 8 other manufacturers
Advertisement
Table of Contents
Related Manuals for injen technology SP1202
Summary of Contents for injen technology SP1202
- Page 1 1- M6 flange nut (#6002) be hot. 1- fender washer (#6010) Injen Technology offers a limited lifetime warranty to the original 1- 12” vinyl trim flex-grip (#6023) purchaser against defects in materials and workmanship. Warranty 1- 3 page instruction claims must be handled through the dealer from which the item was purchased.
- Page 2 (A), continue to press harness clip over ered to prevent the edge from cutting into the intake. the clamp located on the intake side (A). MAF sensor until you hear it snap in place (B). Page 2 of part# SP1202...
- Page 3 5. Check the filter for excessive dirt build up. Clean or replace the filter with an original Injen filter (can be bought on-line at “injenonline.com”). Congratulations! You have just completed the installation of the best intake system sold on the market. Enjoy the added power and performance of your new intake system. Page 3 of part# SP1202...
Need help?
Do you have a question about the SP1202 and is the answer not in the manual?
Questions and answers