Alienware Sentia m3400 User Manual
Alienware Sentia m3400 User Manual

Alienware Sentia m3400 User Manual

Alienware sentia m3400: user guide
Table of Contents

Advertisement

Quick Links

Preface
Notice
The company reserves the right to revise this publication or to change its contents without notice. Infor-
mation contained herein is for reference only and does not constitute a commitment on the part of the man-
ufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or
inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage
resulting from the use (or misuse) of this publication.
This publication and any accompanying software may not, in whole or in part, be reproduced, translated,
transmitted or reduced to any machine readable form without prior consent from the vendor, manufacturer
or creators of this publication, except for copies kept by the user for backup purposes.
Brand and product names mentioned in this publication may or may not be copyrights and/or registered
trademarks of their respective companies. They are mentioned for identification purposes only and are not
intended as an endorsement of that product or its manufacturer.
©December 2005
Trademarks
This product incorporates copyright protection technology that is protected by method claims of certain
U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights
owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and
is intended for home or other limited viewing uses only unless otherwise authorized by Macrovision Cor-
poration. Reverse engineering or disassembly is prohibited.
Intel®, Pentium® and Celeron® are US registered trademarks of Intel Corporation.
I

Advertisement

Table of Contents
loading

Summary of Contents for Alienware Sentia m3400

  • Page 1 Preface Notice The company reserves the right to revise this publication or to change its contents without notice. Infor- mation contained herein is for reference only and does not constitute a commitment on the part of the man- ufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication.
  • Page 2: Fcc Statement

    Preface FCC Statement (Federal Communications Commission) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
  • Page 3: Important Safety Instructions

    IMPORTANT SAFETY INSTRUCTIONS Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment: Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool.
  • Page 4: Instructions For Care And Operation

    Preface Instructions for Care and Operation The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions: Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be dam- aged.
  • Page 5 Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other strong magnetic fields. These can hinder proper performance and damage your data. Follow the proper working procedures for the computer. Shut the computer down properly and don’t forget to save your work.
  • Page 6: Power Safety

    Preface Power Safety The computer has specific power requirements: • Only use a power adapter approved for use with this computer. • Your AC/DC adapter may be designed for international travel but it still requires a Power Safety Warning Before you undertake •...
  • Page 7: Battery Precautions

    Battery Precautions • Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the com- puter. • Do not remove any batteries from the computer while it is powered on. • Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way.
  • Page 8: Cleaning

    Preface Cleaning Do not apply cleaner directly to the computer; use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer. Servicing Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock.
  • Page 9: Travel Considerations

    Travel Considerations Packing As you get ready for your trip, run through this list to make sure the system is ready to go: Check that the battery pack and any spares are fully charged. Power off the computer and peripherals. Close the display panel and make sure it’s latched.
  • Page 10 Preface On the Road In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshoot- ing, keep these points in mind: Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very common.
  • Page 11 Developing Good Work Habits Developing good work habits is important if you need to work in front of the computer for long periods of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints.
  • Page 12 Preface Lighting Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and shoulders. • Position the display to avoid glare or reflections from overhead lighting or outside sources of light. • Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly.
  • Page 13: Table Of Contents

    Notice ...I FCC Statement ...II Instructions for Care and Operation ... IV Power Safety ... VI Battery Precautions ...VII Cleaning ... VIII Servicing ... VIII Travel Considerations ... IX Quick Start Guide Overview ...1-1 Advanced Users ...1-2 Beginners and Not-So-Advanced Users ...1-2 Warning Boxes ...1-2 Not Included ...1-3 System Software ...1-3...
  • Page 14 Preface Configuring the TouchPad and Buttons ...2-11 Audio Features ...2-12 8 Channel Sound Support ...2-13 Adding a Printer ...2-14 USB Printer ...2-14 Parallel Printer ...2-14 Power Management Overview ...3-1 Advanced Configuration and Power Interface ...3-1 The Power Sources ...3-2 AC/DC Adapter ...3-2 Battery ...3-2 Turning on the Computer ...3-3 Power Schemes ...3-4...
  • Page 15 Wireless LAN ...4-12 Bluetooth ...4-12 PC Camera ...4-12 Port Replicator ...4-12 BIOS Utilities Overview ...5-1 The Power-On Self Test (POST) ...5-2 Failing the POST ...5-3 Fatal Errors ...5-3 Non-Fatal Errors ...5-3 The Setup Program ...5-4 Entering Setup ...5-4 Setup Screens ...5-5 Main Menu ...5-6 System Time &...
  • Page 16 Preface Sertek PC Camera Driver Installation (WinXP) ...7-7 PC Camera Audio Setup ...7-8 BisonCap ...7-10 Eliminating Screen Flicker ...7-11 Port Replicator ...7-12 Port Replicator Setup Instructions: ...7-13 Port Replicator Serial (COM) Port Driver (WinXP) ...7-14 Port Replicator Network (LAN) Driver (WinXP) ...7-14 Troubleshooting Overview ...8-1 Basic Hints and Tips ...8-2...
  • Page 17 Intel Video Driver Controls Intel Video Driver Installation ... B-1 Dynamic Video Memory Technology ... B-2 Intel Graphics Properties ... B-3 Schemes ... B-5 Display Devices ... B-6 Attaching Other Displays ... B-7 Display Modes ... B-8 TV Settings ... B-12 Specifications Processor ...
  • Page 18 Preface XVIII...
  • Page 19: Quick Start Guide

    Chapter 1: Quick Start Guide Overview This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following: •...
  • Page 20: Advanced Users

    Quick Start Guide Advanced Users If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to “What to Install” on page 4 - page 6 - 1 in the User’s Manual.
  • Page 21: Not Included

    Not Included Operating Systems (e.g. Windows XP) and applications (e.g. word processing, spreadsheet and database pro- grams) have their own manuals, so please consult the appropriate manuals. System Software Your computer may already come with system software pre-installed. Where this is not the case, or where you are re-configuring your computer for a different system, you will find this manual refers to the Microsoft Win- dows XP (Home &...
  • Page 22: System Startup

    Quick Start Guide System Startup Remove all packing materials. Place the computer on a stable surface. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports. Attach the AC/DC adapter to the DC-In jack on the right of the computer, then plug the AC power cord into an Figure 1 - 1 - Computer with AC/DC Adapter Plugged-In Please note that you should always shut your computer down by choosing the Turn Off Computer command from the Start menu in Windows.
  • Page 23: System Map: Top View With Lcd Panel Open

    System Map: Top View with LCD Panel Open Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft. Use the key combinations to toggle power to the WLAN/Bluetooth...
  • Page 24: Led Indicators

    Quick Start Guide LED Indicators The two sets of LED indicators (LED Status Indica- tors and LED Power & Communication Indicators) on the computer display helpful information about the current status of the computer. Table 1 - 1 - LED Status Indicators Icon Color Number Lock Activated (to...
  • Page 25: Hot-Key Buttons & Keyboard

    Hot-Key Buttons & Keyboard These buttons give instant access to the default Inter- net browser and e-mail program, and to a user-defined application, with one quick button press. To use the “user-defined application Hot-Key Button”, you must install the driver (see “Hot-Key (WinXP)”...
  • Page 26 Quick Start Guide Function Keys To use the function keys, press and hold the Fn key, then press the appropriate function key (F3 - F12 etc.). Function Key Fn + F3 Fn + F4 Sleep Toggle Fn + F5 Decrease Audio Volume Fn + F6 Increase Audio Volume Fn + F7...
  • Page 27: System Map: Front, Rear & Left Views

    System Map: Front, Rear & Left Views 4-in-1 Card Reader The card reader allows you to use the most popular digital storage card formats: MMC (MultiMedia Card) / SD (Secure Digital) / MS (Memory Stick) / MS Pro (Memory Stick Pro) Front Rear Left...
  • Page 28: System Map: Right View

    Quick Start Guide System Map: Right View Figure 1 - 5 - Right View Headphone-Out Jack Microphone-In Jack 2 * USB 2.0 Ports Optical Device Drive Bay (for CD/ DVD Device - see page DC-In Jack CD Emergency Eject If you need to manually eject a CD/DVD (e.g. due to an unex- pected power interruption) you may push the end of a straight- ened paper clip into the emergency eject hole.
  • Page 29: System Map: Bottom View

    System Map: Bottom View The CPU is not a user ser- viceable part. Opening this compartment, or access- ing the CPU in any way, may violate your warranty. Overheating To prevent your computer from overheating make sure nothing blocks the Vent/Fan Intake while the computer is in use.
  • Page 30: Windows Xp Start Menu & Control Panel

    Quick Start Guide Windows XP Start Menu & Control Panel Most of the control panels, utilities and programs within Windows XP (and most other Windows versions) are accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be placed in the Start menu and/or the desktop.
  • Page 31: Video Features

    Video Features Your computer will have built-in Intel (Intel GMA 900) on-board video. You can switch display devices, and configure display options, from the Display Properties control panel in Windows as long as the appropriate vid- eo driver is installed. For more detailed video information see To access Display Properties in Windows: Click Start, point to Settings and click Control Panel (or just click Control Panel).
  • Page 32 Quick Start Guide Intel Display Properties Figure 1 - 8 - Display Properties Desktop 1 - 14 Video Features...
  • Page 33: Display Devices & Options

    Display Devices & Options Besides the built-in LCD, you can also use an external VGA monitor (CRT)/external Flat Panel Display or TV as your display device. A VGA monitor/Flat Panel Display connects to the external monitor port, a TV to the S-Video-Out Port.
  • Page 34: Power Management Features

    Quick Start Guide Power Management Features The Power Options control panel icon in Windows (see page 12) allows you to configure power management features for your computer. You may conserve power through individual components such as the monitor or hard disk (by means of Power Schemes), or you may use either Standby or Hibernate mode to conserve power throughout the system (enable Hibernate support from the control panel as pictured in Figure 1 -...
  • Page 35: Features & Components

    Features & Components Chapter 2: Features & Components Overview Read this chapter to learn more about the following main features and compo- nents of the computer: • Hard Disk Drive • Optical (CD/DVD) Device • 4-in-1 Card Reader • PC Card Slot •...
  • Page 36: Hard Disk Drive

    Features & Components Power Safety Before attempting to access any of the inter- components your computer please ensure that the ma- chine is not connected to the AC power, and that the machine is turned off. Also ensure that all peripheral ca- bles, including phone lines, are disconnected from the computer.
  • Page 37: Optical (Cd/Dvd) Device

    Optical (CD/DVD) Device There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The ac- tual device will depend on the module you purchased (see page C - 3). The optical device is usually labeled “Drive D:” and may be used as a boot device if properly set in the BIOS (see Loading Discs To insert a CD/DVD, press the open button...
  • Page 38: Handling Cds Or Dvds

    Features & Components CD Emergency Eject If you need to manually eject a CD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into emergency eject hole. However please do NOT use a sharpened pencil or similar object that may break...
  • Page 39: Dvd Regional Codes

    DVD Regional Codes To change the DVD regional codes see page 1 - DVD Regional Coding Region Geographical Location USA, Canada Western Europe, Japan, South Africa, Middle East & Egypt South-East Asia, Taiwan, South Korea, The Philippines, Indonesia, Hong Kong South &...
  • Page 40: 4-In-1 Card Reader

    Features & Components Card Reader Cover Make sure you keep the cover in the card reader when not is use. This will help pre- vent foreign objects and/or dust getting in to the card reader. Figure 2 - 4 Removable Disks Card Reader 2 - 6 4-in-1 Card Reader 4-in-1 Card Reader...
  • Page 41: Pc Card Slot

    PC Card Slot The computer is equipped with a PCMCIA 3.3V/5V slot for one type II PC- MCIA CardBus PC Card Slot. Make sure you install the PCMCIA/Card Read- er Card driver (see “PCMCIA/Card Reader (WinXP)” on page 4 - Inserting and Removing PC Cards •...
  • Page 42: Auto Mail Checker

    Features & Components Auto Mail Checker After you have installed the driver for the Auto Mail Checker program (see “AutoMail (WinXP)” on page 4 - 11) you may then configure it to give you notification when you receive new mail. You must be online to receive this notification (note that this program only supports the POP3 protocol), and your default mail program does not need to be open.
  • Page 43 You may then configure the options for your mailserver, name, password, pro- gram and method(s) of notification. Features & Components Note Check with your Inter- net Service Provider, network administrator or Mail Service provid- er for details on what to put on these pages.
  • Page 44: Application Hot-Key

    Features & Components Application.exe You will need to locate the actual application executable (.exe) file, not just the shortcut. To find the application right-click its shortcut on the desktop and click Properties. Click the shortcut (tab) and see where the execut- able file is located by clicking the Find Tar- get (button).
  • Page 45: Touchpad And Buttons/Mouse

    TouchPad and Buttons/Mouse The TouchPad is an alternative to the mouse; however, you can also add a mouse to your computer through one of the USB ports. The TouchPad buttons function in much the same way as a two-button mouse. The central button may be configured to function as you require.
  • Page 46: Audio Features

    Features & Components Sound Volume Adjustment How high the sound volume can be set de- pends on the setting of volume control within Windows (and volume control function keys on the computer). Click the Volume icon on the taskbar to check the setting.
  • Page 47: Channel Sound Support

    Features & Components 8 Channel Sound Support If you wish to configure your system for 8 channel sound support, then the fol- lowing ports should be used as outputs. Double-click the appropriate icon (e.g. ) to bring up the “Connected device:” dialog box to configure the output port.
  • Page 48: Adding A Printer

    Features & Components Parallel Printer After setting up the printer attach the paral- lel cable to the printer. Connect the printer’s parallel cable to the Parallel to USB con- verter, and then plug the converter into the USB port. Turn ON the printer, then turn ON the com- puter.
  • Page 49: Power Management

    Chapter 3: Power Management Overview To conserve power, especially when using the battery, your computer uses the ACPI power management system. Power management conserves power by controlling individual components of the computer (the monitor and hard disk drive) or the whole system. This chapter covers: •...
  • Page 50: The Power Sources

    Power Management Port Replicator AC/ DC Adapter You will be provided with a 90W AC/DC adapter if you pur- chase the port replica- tor option. If you are using the computer with the Port Replicator, then you must use the 90W AC/DC adapter power the port replica-...
  • Page 51: Turning On The Computer

    Turning on the Computer Now you are ready to begin using your computer. To turn it on simply press the power button on the front panel. When the computer is on, you can use the power button as a Standby/Hiber- nate/Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will shut the com- puter down).
  • Page 52: Power Schemes

    Power Management Resuming Operation The system can re- sume from Monitor or Hard Disk Standby by pressing the Sleep/ Resume key combina- tion (Fn + F4), or pow- er button. Figure 3 - 1 Power Schemes 3 - 4 Power Schemes Power Schemes You can set your computer to conserve power through individual components by means of Power Schemes.
  • Page 53 Power Management Each Windows Power Scheme will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power). Choose the Home/Office Desk scheme for maximum performance when the computer is powered from an AC power source.
  • Page 54: System Power Options

    Power Management System Power Options You can use the system power options to stop the computer’s operation and restart where you left off. This system features Standby and Hibernate sleep mode levels (Hibernate mode will need to be enabled by clicking the option in the Hibernate tab in the Power Options control panel - Figure 3 - 2 on page 3 -...
  • Page 55: Standby

    Standby Standby saves the least amount of power, but takes the shortest time to return to full operation. During Standby the hard disk is turned off, and the CPU is made to idle at its slowest speed. All open applications are retained in memo- ry.
  • Page 56: Configuring The Power Button

    Power Management Figure 3 - 3 Power Options (Advanced - Power Buttons) 3 - 8 Configuring the Power Button Configuring the Power Button The power button may be set to send the computer in to either Standby or Hi- bernate mode (Figure 3 - 3).
  • Page 57: Battery Information

    Battery Information Please follow these simple guidelines to get the best use out of your battery. New Battery Always completely discharge, then fully charge, a new battery (see FAQ” on page 3 - 12 for instructions on how to do this). Battery Life Your computer’s battery life is dependent upon many factors, including the programs you are running, and peripheral devices attached.
  • Page 58: Recharging The Battery With The Ac/Dc Adapter

    Power Management Conserving Battery Power To conserve battery power: Lower the brightness lev- el of the LCD display. The system will decrease LCD brightness slightly to save power when it is not pow- ered by the AC/DC adapt- Close modem or commu- nication applications when they are not being...
  • Page 59: Proper Handling Of The Battery Pack

    Proper handling of the Battery Pack • DO NOT disassemble the battery pack under any circumstances • DO NOT expose the battery to fire or high temperatures, it may explode • DO NOT connect the metal terminals (+, -) to each other Damaged Battery Warning Should you notice any physical defects (e.g.
  • Page 60: Battery Faq

    Power Management Caution Danger of explosion if battery is incorrectly replaced. Replace only with the same equivalent type recommended by the manufacturer. Dis- card used battery ac- cording manufacturer’s structions. 3 - 12 Battery Information Battery FAQ How do I completely discharge the battery? Use the computer with battery power until it shuts down due to a low battery.
  • Page 61: Drivers & Utilities

    Chapter 4: Drivers & Utilities This chapter deals with installing the drivers and utilities essential to the operation or improvement of some of the computer’s subsystems. The system takes advantage of some newer hardware compo- nents for which the latest versions of most available operating systems haven’t built in drivers and utili- ties.
  • Page 62 Drivers & Utilities Navigate (Browse..) to D: You will notice that many of the instructions for driver installation require you to “Navigate (Browse) to D:”. We assume that you will install all drivers and utilities from the built-in CD device and it is assigned to “Drive D:”.
  • Page 63: Service Packs

    Service Packs Check the warnings on the following pages regard- ing installation of the appropriate Service Pack for your Windows OS. Make sure you have installed the appropriate Service Pack before installing all the drivers. Service Pack Installed To see which Service Pack is currently installed on your computer go to the General tab of the System control panel.
  • Page 64: Authorized Driver Message

    Drivers & Utilities Authorized Driver Message If you receive a message telling you that the driver you are installing is not authorized (Digital Signa- ture Not Found), just click Yes or Continue Any- way to ignore the message and continue the installation procedure.
  • Page 65: Driver Installation

    Driver Installation Insert the Device Drivers & Utilities + User’s Man- ual CD-ROM and click Install WinXP Drivers (button). If you wish to install the drivers manually see page 4 - 7 Figure 4 - 2 - Drivers Installer Screen 1 Drivers &...
  • Page 66: Driver Installation Procedure

    Drivers & Utilities WinXP SP2 Driver Install the appropriate Service Pack for WinXP Chipset Video Audio Modem TouchPad PCMCIA/Card Reader Hot-Key AutoMail (Manual Driver Installation Only) Intel Wireless LAN Bluetooth PC Camera Port Replicator Serial Port Port Replicator Network (LAN) Port Table 4 - 1 - Driver Installation 4 - 6 Driver Installation...
  • Page 67: Manual Driver Installation

    Manual Driver Installation If you wish to install the drivers manually, click the Exit button to quit the Drivers Installer applica- tion, then follow the manual installation procedure for each driver. The manual installation procedure begins with instructions on how to browse to the executable file;...
  • Page 68: Chipset (Winxp)

    Drivers & Utilities Chipset (WinXP) 1. Click 1.Install Chipset Driver > Yes from the Drivers Installer menu. Click Start (menu) > Run... and navigate (Browse..) to D:\Drivers\Chipset\Setup.exe and click 2. Click Next > Yes > Next. 3. Click Finish to restart the computer. Video (WinXP) 1.
  • Page 69: Lan (Winxp)

    LAN (WinXP) 1. Click 4.Install LAN Driver > Yes from the Drivers Installer menu. Click Start (menu) > Run... and navigate (Browse...) to D:\Drivers\LAN\Setup.exe and click OK. 2. To continue click Next. 3. Click Finish. 4. The network settings can now be config- ured.
  • Page 70: Touchpad (Winxp)

    Drivers & Utilities TouchPad (WinXP) 1. Click 6.Install TouchPad Driver > Yes from the Drivers Installer menu. Click Start (menu) > Run... and navigate (Browse..) to D:\Drivers\TouchPad\SETUP.EXE and click OK. 2. Click Next > Next (click Continue Anyway if asked if you want to continue at any time). 3.
  • Page 71: Hot-Key (Winxp)

    Hot-Key (WinXP) 1. Click 8.Install Hotkey Utility > Yes from the Drivers Installer menu. Click Start (menu) > Run... and navigate (Browse..) to D:\Drivers\Hotkey\Setup.exe and click 2. Choose the language you prefer, and click 3. Click Next. 4. Click Finish to restart your computer. 5.
  • Page 72: Wireless Lan

    Drivers & Utilities Wireless LAN See the introduction in “Intel PRO/Wireless Mini- PCI WLAN Module” on page 7 - installation procedure. Bluetooth See install procedure in “Bluetooth Module” on page 7 - 4 - 12 Driver Installation PC Camera See install procedure in 2, and check the Installation (WinXP)”...
  • Page 73: Bios Utilities

    Chapter 5: BIOS Utilities Overview This chapter gives a brief introduction to the computer’s built-in software: Diagnostics: The POST (Power-On Self Test) Configuration: The Setup utility If your computer has never been set up, or you are making important changes to the system (e.g.
  • Page 74: The Power-On Self Test (Post)

    BIOS Utilities POST Screen 1.BIOS information 2.CPU type 3.Memory status 4.Enter Setup prompt appears only during POST Note: POST screen as pictured is for guideline purposes only. POST screen on your compu- ter may appear slightly different. Figure 5 - 1 POST Screen 5 - 2 The Power-On Self Test (POST) The Power-On Self Test (POST)
  • Page 75: Failing The Post

    BIOS Utilities Failing the POST Errors can be detected during the POST. There are two categories, “fatal” and “non-fatal”. Fatal Errors These stop the boot process and usually indicate there is something seriously wrong with your system. Take the computer to your service representative or authorized service center as soon as possible.
  • Page 76: The Setup Program

    BIOS Utilities The Setup Program The Phoenix Setup program tells the system how to configure itself and man- age basic features and subsystems (e.g. port configuration). Entering Setup To enter Setup, turn on the computer and press F2 during the POST. The prompt (Press F2 to Enter Setup) seen in Figure 5 - 1 is usually present for a...
  • Page 77: Setup Screens

    Setup Screens The following pages contain additional advice on portions of the Setup. Along the top of the screen is a menu bar with five (5) menu headings. When you select a heading, a new screen appears. Scroll through the features listed on each screen to make changes to Setup.
  • Page 78: Main Menu

    BIOS Utilities Figure 5 - 2 Main Menu 5 - 6 Main Menu Main Menu PhoenixBIOS Setup Utility Main Main Advanced Security System Time: [22:11:05] System Date: [05/02/2005] IDE Channel 0 Master [30006MB] IDE Channel 0 Slave [CD-ROM] System Memory 640 MB Extended Memory 1014 MB...
  • Page 79: Ide Channel 0 Master/Slave (Main Menu)

    BIOS Utilities IDE Channel 0 Master/Slave (Main Menu) Pressing Enter opens the sub-menu to show the configuration of either a CD Device or HDD that on the computer’s IDE Channel 0. Use the Auto (Type:) setting to have the items configured automatically for you. System/Extended Memory (Main Menu) This item contains information on the system memory, and is not user config- urable.
  • Page 80: Advanced Menu

    BIOS Utilities Figure 5 - 3 Advanced Menu 5 - 8 Advanced Menu Advanced Menu PhoenixBIOS Setup Utility Main Advanced Advanced Security Installed O/S: [WinXP] Reset Configuration Data: [No] Large Disk Access Mode: [DOS] Local Bus IDE adapter: [Primary] Legacy USB Support: [Enabled] Summary screen: [Disabled]...
  • Page 81: Reset Configuration Data (Advanced Menu)

    BIOS Utilities Reset Configuration Data (Advanced Menu) This item is set to No as default. You can change the setting to Yes if you have installed a new add-on which has reconfigured the system, resulting in such a serious system conflict that the operating system is unable to boot. Large Disk Access Mode (Advanced Menu) Select “Other”...
  • Page 82: Security Menu

    BIOS Utilities Figure 5 - 4 Security Menu Security Menu changes make here affect the access to the Setup utility itself, and also access to your ma- chine as it boots up af- ter you turn it on. These settings do not affect your machine or network passwords...
  • Page 83: Set User Password (Security Menu)

    Set User Password (Security Menu) You can set a password for user mode access to the Setup utility. This will not affect access to the computer OS, (only the Setup utility) unless you choose to set a Password on Boot (see below). Many menu items in the Setup utility cannot be modified in user mode.
  • Page 84: Boot Menu

    BIOS Utilities Figure 5 - 5 Boot Menu 5 - 12 Boot Menu Boot Menu PhoenixBIOS Setup Utility Main Advanced Security Boot priority order: USB FDC: IDE 1: TSSTcorpCD/DVDW TS-L532A- IDE 0: TOSHIBA MK3025GAS-(PM) PCI LAN: Realtek Boot Agent USB CDROM: USB HDD: IDE 2: IDE 3:...
  • Page 85 Boot devices usually are hard drives, floppy drives, and CD-ROMs/DVD- ROMs and Networks (LANs). When you specify a device as a boot device on the Boot Menu, it requires the availability of an operating system on that device. Most home computers come with an operating system already installed on “Drive C:”.
  • Page 86: Exit Menu

    BIOS Utilities Figure 5 - 6 Exit Menu 5 - 14 Exit Menu Exit Menu PhoenixBIOS Setup Utility Main Advanced S S e e c c u u r r i i t t y y Exit Saving Changes Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes...
  • Page 87: Upgrading The Computer

    Chapter 6: Upgrading The Computer Overview This chapter contains information on upgrading the computer. Follow the steps outlined to make the desired upgrades. If you have any trouble or prob- lems you can contact your service representative for further help. Before you begin you will need: •...
  • Page 88: When Not To Upgrade

    Upgrading The Computer Power Safety Warning Before you undertake any upgrade proce- dures, make sure that you have turned off the power, discon- nected all peripherals and cables (including telephone lines). It is advisable to also re- move your battery in order to prevent acci- dentally turning...
  • Page 89: Removing The Battery

    Removing the Battery If you are confident in undertaking upgrade procedures yourself, for safety reasons it is best to remove the battery. Turn the computer off, and turn it over. Slide the latch in the direction of the arrow, and hold it in place. Slide the battery in the direction of the arrow Removing the Battery 6 - 3 Upgrading The Computer...
  • Page 90 Upgrading The Computer Figure 6 - 2 Battery Up Figure 6 - 3 Battery Out 6 - 4 Removing the Battery Lift the battery out in the direction of the arrow Lift the battery out.
  • Page 91: Upgrading The Hard Disk Drive

    Upgrading the Hard Disk Drive The hard disk drive can be taken out to accommodate other 2.5" parallel (PA- TA) hard disk drives with a height of 9.5mm (h) (see 3). Follow your operating system’s installation instructions, and install all necessary drivers and utilities (as outlined in 5), when setting up a new hard disk.
  • Page 92 Upgrading The Computer Figure 6 - 5 HDD & Case Assembly Removal 6 - 6 Upgrading the Hard Disk Drive Pull the tab to slide the hard disk and case assembly in the direction of arrow Lift the hard disk and case assembly out of the bay in the direction of arrow Remove screws to release the hard disk reverse the process to install any new hard disk.
  • Page 93: Upgrading The Optical (Cd/Dvd) Device

    Upgrading the Optical (CD/DVD) Device Turn off the computer, and turn it over and remove the battery. Locate the memory bay cover and remove screws Remove the bay cover. Use a screwdriver to carefully push out the optical device at point Reverse the process to install the new device.
  • Page 94: Upgrading The System Memory (Ram)

    Upgrading The Computer Figure 6 - 7 RAM Bay Screws 6 - 8 Upgrading the System Memory (RAM) Upgrading the System Memory (RAM) The computer has two memory sockets for 200 pin Small Outline Dual In-line (SO-DIMM) DDRII (DDR2) type memory modules (see page C - 2 for details of supported module types).
  • Page 95 Remove the bay cover Gently pull the two release latches on the sides of the memory socket in the direction indicated by the arrows ( & ) in Figure 6 - Upgrading the System Memory (RAM) 6 - 9 Upgrading The Computer Figure 6 - 8 RAM Cover Removed...
  • Page 96 Upgrading The Computer Figure 6 - 10 RAM Removal 6 - 10 Upgrading the System Memory (RAM) The RAM module will pop-up, and you can remove it. Pull the latches to release the second module if necessary. Insert a new module holding it at about a 30° angle and fit the connectors firmly into the memory slot.
  • Page 97: Upgrading The Processor

    Upgrading the Processor If you want to upgrade your computer by replacing the existing processor with a faster/new one you will need to contact your customer service representa- tive. We recommend that you do not do this yourself, since if it is done incor- rectly you may damage the processor or mainboard.
  • Page 98 Upgrading The Computer 6 - 12...
  • Page 99: Modules & Options

    Chapter 7: Modules & Options Overview This chapter contains the information on the WLAN, Bluetooth, PC Camera and Port Replicator modules which may come with your computer, depend- ing on the configuration purchased. If you are unsure please contact your ser- vice representative.
  • Page 100: Intel Pro/Wireless Mini-Pci Wlan Module

    Modules & Options Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft. Use the Fn + F11 key combination toggle power to the WLAN mod-...
  • Page 101: Intel Wlan Driver Installation

    Intel WLAN Driver Installation 1. Make sure the module is powered on, then insert the Intel PROSet/ Wireless CD-ROM into the CD/DVD drive. 2. Click Install Software (button). 3. Click the button to accept the license and click Next > Next > OK. 4.
  • Page 102: Bluetooth Module

    Modules & Options Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft. Use the Fn + F12 key combination toggle power to the optional...
  • Page 103 Modules & Options User Guide View the BlueSoleil User Guides from the Help Menu (or press the F1 key) in the IVT Corporation BlueSo- leil - Main Window control panel. Click BlueSoleil User Guides in the Con- tents tab, and click to select the appropriate User Guide from the panel on the right.
  • Page 104: Pc Camera

    Modules & Options Taking Still Pictures Double-click the My Computer icon on the desktop, or go the Start menu and point to My Computer, then click it. Double-click BisonCam, NB Pro icon. Click Take a new pic- ture in the Camera Tasks box.
  • Page 105: Sertek Pc Camera Driver Installation (Winxp)

    Sertek PC Camera Driver Installation (WinXP) 1. Press the Fn + F10 key combination to power on the PC Camera module (click Cancel if you see a “New Hardware Found” message) . 2. Insert the PC Camera CD-ROM into the CD/DVD drive. 3.
  • Page 106: Pc Camera Audio Setup

    Modules & Options 7 - 8 PC Camera PC Camera Audio Setup If you wish to capture video & audio with your camera, it is necessary to setup the audio recording options in Windows. Go to the Start menu and point to Settings (or just click Control Panel) and click Control Panel, then double-click the Sounds &...
  • Page 107 Modules & Options Figure 7 - 4 Audio Setup (Windows XP) PC Camera 7 - 9...
  • Page 108: Bisoncap

    Modules & Options Pre-Allocating File Space You may pre-allocate the file size for the cap- ture file in the Bison- Cap program. You can choose to ignore this by clicking Cancel. Pre-allocating space on the hard disk can improve the capture quality (particularly of large capture files), by reducing the amount of...
  • Page 109: Eliminating Screen Flicker

    Eliminating Screen Flicker If you find that the video screen in the BisonCap program is flickering, you can try to adjust the setting in the Video Capture Filter options. Run the BisonCap program. Go to Options and scroll down to select “Video Capture Filter...”. Click either 50Hz or 60Hz under Frequency in Property Page (tab).
  • Page 110: Port Replicator

    Modules & Options Port Replicator AC/DC Adapter You will be provided with a 90W AC/DC adapter if you pur- chase the port replica- tor option. If you are using the computer with the Port Replicator, then you must use the 90W AC/DC adapter power the port replica-...
  • Page 111: Port Replicator Setup Instructions

    Port Replicator Setup Instructions: Turn the computer OFF. Attach the Port Replicator’s external monitor cable to the external monitor port on the rear of the computer. Attach the Port Replicator’s power cable to the DC-In jack on the right of the computer.
  • Page 112: Port Replicator Serial (Com) Port Driver (Winxp)

    Modules & Options 7 - 14 Port Replicator Port Replicator Serial (COM) Port Driver (WinXP) 1. Insert the provided Port Replicator CD into the computer’s CD/DVD drive. 2. Click Start (menu) > Run... and navigate (Browse...) to D:\PL-2303 Driver Installer\PL-2303 Driver Installer.exe and click OK.
  • Page 113 6. Click "+" next to Other devices (if its sub-menu items are not shown). 7. Double-click AX88772 and click Driver (tab). 8. Click Update Driver (button). 9. Select “No, not this time” then click Next. 10. When the Hardware Update Wizard appears, click “Install from a list or specific location (Advanced)”...
  • Page 114 Modules & Options 7 - 16...
  • Page 115: Troubleshooting

    Troubleshooting Chapter 8: Troubleshooting Overview Should you have any problems with your computer, before consulting your service representative, you may want to try to solve the problem yourself. This chapter lists some common problems and their possible solutions. This can’t anticipate every problem, but you should check here before you panic. If you don’t find the answer in these pages, make sure you have followed the instructions carefully and observed the safety precautions in the preface.
  • Page 116: Basic Hints And Tips

    Troubleshooting Basic Hints and Tips Many of the following may seem obvious but they are often the solution to a problem when your computer appears not to be working. • Power - Is the computer actually plugged into a working electrical outlet? If plugged into a power strip, make sure it is actually working.
  • Page 117: Backup And General Maintenance

    Backup and General Maintenance • Always backup your important data, and keep copies of your OS and programs safe, but close to hand. Don’t forget to note the serial numbers if you are storing them out of their original cases, e.g. in a CD wallet.
  • Page 118: Viruses

    Troubleshooting Viruses • Install an Anti-Virus program and keep the definitions file (the file which tells your program which viruses to look for) up to date. New computer viruses are discovered daily, and some of them may seriously harm your computer and cause you to lose data. Anti-Virus programs are commercially available and the definitions file updates are usually downloadable directly from the internet.
  • Page 119: Upgrading And Adding New Hardware/Software

    Upgrading and Adding New Hardware/Software • Do not be tempted to make changes to your Windows Registry unless you are very sure of what you are doing, otherwise you will risk severely damaging your system. • Don’t open your computer or undertake any repair or upgrade work if you are not comfortable with what you are doing.
  • Page 120 Troubleshooting • Thoroughly check any recent changes you made to your system as these changes may affect one or more system components, or software programs. If possible, go back and undo the change you just made and see if the problem still occurs. •...
  • Page 121: Power

    Power Problem You turned on the power Battery missing / incorrectly installed. Check the battery bay, make sure the battery is but it doesn’t work. present and seated properly (the design of the battery only allows it to go in one way). Make sure there’s nothing interfering with the battery contacts.
  • Page 122 Troubleshooting Problem The computer feels too hot. You will be provided with a 90W AC/DC adapter if you purchase the port replicator option. If you are using the computer with the Port Replicator, then you must use the 90W AC/DC adapter to power the port replicator and computer (DO NOT USE the computer’s 65W AC/DC adapter to power the Port Replicator).
  • Page 123: Display

    Display Problem Nothing appears The system is in a power saving mode. Toggle the sleep/resume key combination, Fn + F4 screen. (see “Sleep Button” on page 3 - The screen controls need to be adjusted. Toggle the screen control key combinations Fn + F8/F9.
  • Page 124: Boot Password

    Troubleshooting Boot Password Problem forget boot If you forget the password, you may have to discharge the battery of the CMOS. Contact password. your service representative for help. If you choose to set a boot password, NEVER forget your password. The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk.
  • Page 125: Audio & Cd Device

    Audio & CD Device Problem The sound cannot be The volume might be set too low. Check the volume control in the Volume Control Panel heard or the volume is in the Windows taskbar, or use the key combination Fn + F5 and F6 (see very low.
  • Page 126: Keyboard

    Troubleshooting Keyboard Problem Unwelcome numbers If the LED appear when typing. If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. The system will detect and enable it automatically. However special functions/hot keys unique to the system’s regular keyboard may not work.
  • Page 127: Operation

    Operation Problem The system freezes or The system’s power saving features have timed-out. Use the AC/DC adapter, press the the screen goes dark. sleep (Fn + F4) key combination, or press the power button if no LEDs are lit. The system never goes Power Options features are not enabled.
  • Page 128: Modules

    Troubleshooting Modules Problem Wireless LAN/ The modules are off. Check the LED indicator Bluetooth modules on or off (see cannot be detected. Fn + F11 (WLAN) or Fn + F12 (Bluetooth) key combination(s) in order to enable the modules (see The PC Camera modules The module is off.
  • Page 129: Interface (Ports & Jacks) Overview

    Interface (Ports & Jacks) Appendix A: Interface (Ports & Jacks) Overview The following chapter will give a quick description of the interface (ports & jacks) which allow your com- puter to communicate with external devices, connect to the internet etc. Interface (Ports &...
  • Page 130: Notebook Ports And Jacks

    Interface (Ports & Jacks) Notebook Ports and Jacks Item Description Built-In Microphone The built-in microphone allows you to record on your computer Card Reader Port The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device.
  • Page 131: Microphone-In Jack

    Item Microphone-In Jack Plug an external microphone in to this jack to record on your computer. Mini-IEEE 1394 Port This port allows a high-speed connection to various peripheral devices, e.g. external disk drives and digital cameras (see note below). The Mini-IEEE 1394 port only supports SELF POWERED IEEE 1394 devices. RJ-11 Phone Jack This port connects to the built-in modem.
  • Page 132: S/Pdif-Out Jack

    Interface (Ports & Jacks) Item Description S/PDIF-Out Jack This S/PDIF (Sony/Philips Digital Interface Format) Out Jack allows you to connect your DVD-capable PC to a Dolby AC-3 compatible receiver for “5.1” or ‘dts’ surround sound. S-Video-Out Port Connect your television to your computer and view DVDs, VCDs or anything else your computer can display.
  • Page 133: Dc-In Jack

    Interface (Ports & Jacks) Optional Port Replicator Ports and Jacks Item Description DC-In Jack Plug the supplied AC/DC adapter into this jack to power your computer. External Monitor (VGA) This port allows you to connect an external monitor, or Flat Panel Display, to get dual video Port or simultaneous display on the LCD and external monitor/FPD (see “Display Devices”...
  • Page 134: Usb 2.0/1.1 Ports

    Interface (Ports & Jacks) Item Description USB 2.0/1.1 Ports These USB 2.0 compatible ports (USB 2.0 is fully USB 1.1 compliant) are for low-speed peripherals such as keyboards, mice or scanners, and for high-speed peripherals such as external HDDs, digital video cameras or high-speed scanners etc. Devices can be plugged into the computer, and unplugged from the computer, without the need to turn the system off (if the power rating of your USB device is 500mA or above, make sure you use the power supply which comes with the device).
  • Page 135: Intel Video Driver Controls

    Appendix B: Intel Video Driver Controls The basic settings for configuring the LCD are outlined in on page 1 - Intel Video Driver Installation Make sure you install all the drivers in the order indicated in page 4 - 6. Instructions for installing the video driver are repeated below. 1.
  • Page 136: Dynamic Video Memory Technology

    Intel Video Driver Controls DVMT Notes DVMT is not user-con- figurable. DVMT is not local vid- eo memory. DVMT will not function in MS-DOS. DOS uses the legacy memory in- dicated. Figure B - 1 DVMT Memory Requirements B - 2 Dynamic Video Memory Technology Dynamic Video Memory Technology ®...
  • Page 137: Intel Graphics Properties

    Intel Graphics Properties More advanced video configuration options are provided by the Intel(R) Graphics Media Accelerator Driver. Open Display Properties (see “Video Features” on page 1 - Click the Intel(R)... tab and click Graphics Properties (button). You can also access Graphics Properties from the Windows Intel(R) GMA Driver for Mobile control panel.
  • Page 138 Intel Video Driver Controls Intel Graphics Properties Note that the Graphics Properties control panel is entitled Mobile Intel(R) 915GM/GMS, 910GML Express Chipset Fami- Figure B - 3 Intel Graphics Properties (Control Panel Tabs) B - 4 Intel Graphics Properties You may make changes to the Devices, Color, Schemes, Hot Keys by clicking the appropriate tab and adjusting the setting, then clicking OK.
  • Page 139: Schemes

    Schemes Use Schemes to configure quick settings for applications which require spe- cific resolution and color settings in order to run properly e.g. games, multi- media programs. To set the schemes: Go to the Graphics Properties control panel (see ties” on page B - Configure your display configuration, resolution etc.
  • Page 140: Display Devices

    Intel Video Driver Controls Function Key Combination You can use the Fn + F7 key combination to toggle through the dis- play options: • Notebook Only • External Display Only • Notebook + External Display Make sure you give the displays enough time to refresh.
  • Page 141: Attaching Other Displays

    Attaching Other Displays If you prefer to use a monitor or flat panel display, connect it to the external monitor port on the left of the computer. Attach your external monitor to the external monitor port, and turn it on. Go to the Graphics Properties control panel (see Properties”...
  • Page 142: Display Modes

    Intel Video Driver Controls Function Key Combination You can use the Fn + F7 key combination to toggle through the dis- play options: • Notebook Only • External Display Only • Notebook + External Display Make sure you give the displays enough time to refresh.
  • Page 143 To Enable Intel(R) Dual Display Clone Mode Attach your external monitor to the external monitor port (or TV to the S- Video-Out Port), and turn it on. Go to the Graphics Properties control panel (see Properties” on page B - 3) and click Devices (tab).
  • Page 144 Intel Video Driver Controls Display Settings Extended Desktop You can have different Colors, Screen Area and Monitor Refresh Rates for each display device provided your monitor can support them. You can drag the mon- itor icons to match the physical layout of your displays.
  • Page 145 To Enable Extended Desktop (Display Properties) Attach your external monitor to the external monitor port (or TV to the S- Video-Out Port), and turn it on. Click Start, point to Settings (or click Control Panel) and click Control Panel (if you are in Category View choose Appearance and Themes). Double-click Display (icon).
  • Page 146: Tv Settings

    Intel Video Driver Controls Function Key Combination You can use the Fn + F7 key combination to toggle through the dis- play options: • Notebook Only • External Display Only • Notebook + External Display Make sure you give the displays enough time to refresh.
  • Page 147: Specifications

    Specifications Appendix C: Specifications Latest Specification Information The specifications listed in this Appendix are correct at the time of going to press. Certain items (particularly pro- cessor types/speeds and CD/DVD device types) may be changed or updated due to the manufacturer's release schedule.
  • Page 148: Processor

    Specifications Feature Processor Intel Pentium® M Processor (478-pin) Micro-FC-PGA Package Models 730/ 740/ 750/ 760/ 770/ 780 Intel Celeron® M Processor (478-pin) Micro-FCPGA Package Models 350/ 360/ 370/ 380/ 390 Core Logic Intel 915GM + ICH6-M Memory Two 200 Pin SO-DIMM Sockets Supporting DDRII (DDR2) 400 / 533 MHz 128-bit Wide DDRII (DDR2) Data Channel Memory Expandable up to 2GB (256/ 512/ 1024 MB DDRII Modules) (Note: Do Not Use Other Module Types)
  • Page 149: Storage

    Feature Storage One Changeable 12.7mm(h) Optical Device (CD/DVD) Type Drive (see for drive options) Easy Changeable 2.5" 9.5 mm (h) IDE HDD with PATA (Parallel) Interface Supports ATA 100/ 66/ 33 Audio Integrated AZALIA Compliant Interface (HDA) 3D Stereo Enhanced Sound System Sound-Blaster PRO™...
  • Page 150: Card Reader

    Specifications Feature Card Reader Embedded 4-in-1 Card Reader (MS/ MS PRO/ SD/ MMC) Communication AZALIA 56K Plug & Play Fax/Modem v.90/92 Compliant 10Mb/ 100Mb/ 1000Mb Fast Ethernet Intel® PRO/Wireless 2915ABG Mini PCI Wireless LAN Module (Factory Option) Bluetooth Module - Version 1.2 (Factory Option) 300K PC Camera with USB Interface (Factory Option) 1.3M PC Camera with USB Interface Power...
  • Page 151: Physical Dimensions & Weight

    Feature Physical 333mm (w) * 243mm (d) * 24-33mm (h) Dimensions & Weight Optional Optical Drive Module Options: DVD-ROM Drive Module DVD/CD-RW Combo Drive Module DVD-Dual Drive Module Port Replicator (10/100 Base-T Ethernet Port, 4 * USB 2.0 Ports, Serial Port, Parallel Port, External Monitor Port, DC-In Jack) (Note: Port Replicator requires the supplied 90W power adapter)
  • Page 152 Specifications C - 6...

Table of Contents