Page 3
The reproduction and distribution of the documentation and software supplied with this product and the use of its contents is subject to written authorization from devolo. We reserve the right to make any alterations that arise as the result of technical de- velopment.
Magic! te, the device connector, as well as the icons used In no time at all, devolo Magic transforms your on the package: house into a multimedia home that is ready for the future today.
CE marking to declare that the product meets all 1.2 Intended use applicable European regulations and has been subjected to the pres- Use devolo devices, devolo software and the provi- cribed conformity assessment ded accessories as described to prevent damage procedures.
1.3 CE Conformity and the power line*. devolo devices may not be in- stalled at a height above two metres unless an ad- This product complies with the technical ditional fastening mechanism is available.
Do not insert any objects into the openings of devolo devices. devolo devices may be operated only on a mains devolo devices must not be placed directly power supply as described on the rating plate.
(such as rain or other water). if the devolo device is inoperable. if the housing of the devolo device is damaged. CAUTION! Damage to housing from cleaning agents containing solvents Clean only electroless and with dry cloth Do not plug devolo devices directly into each other.
11 Introduction 2 Introduction 2.1 devolo Magic Home is where devolo Magic is – in no time at all, devolo Magic transforms your house or flat into a multimedia home of the future with noticeably higher speed, more stability and greater range,...
Its integrated electrical socket can be used (like a normal wall socket) to supply power to an To set up a devolo Magic network, you need additional network device or a power strip. at least two devolo Magic devices. For tech-...
3 minutes. Expanding an existing devolo Magic network by adding another devolo Magic adapter In order to use a new devolo Magic 2 LAN your devolo Magic- network, first you have to connect it to your existing devolo Magic adapters devices as a network.
Page 14
The LED of this adapter now also flashes white. After a short time, the flashing LED beco- mes a steady white light. The devolo Magic adapter has been successfully integrated into your existing devolo Magic network.
Red LED Flashes at in- Status 1: Cannot be disabled tervals of 0.5 The reset of the devolo Magic adapter was sec. (on/off) successful. The PLC/reset button has been pressed and held for 10 seconds. Status 2: The devolo Magic adapter (once again) has the factory default settings.
Page 16
The other network nodes are in standby mode and cannot currently be accessed over the mains supply. The PLC LEDs of the other devolo Magic adapters flash white only for a short time. Status 2: The connection to the other network nodes has been interrupted.
Page 17
White Lights up stea- The devolo Magic connection does not have Can be disabled any issues and the devolo Magic adapter is ready to operate. White Flashes at in- The devolo Magic adapter is in standby mo- Can be disabled tervals de.***...
For more information about this, refer Connecting devolo Magic 2 LAN 2.3.2Network connection You can use the network connection on the devolo Magic adapter to connect it to a PC or tele- vision using a standard network cable. devolo Magic 2 LAN...
AG reserves the right to change the packa- ge contents without prior notice. This chapter tells you everything you need to know to set up and use your devolo Magic 2 LAN . We 3.2 System requirements describe how to connect the adapter and briefly describe the devolo software.
Magic adapters, the new adapter devolo Magic adapter has been successfully integrated into your Before you can use the devolo Magic 2 LAN existing devolo Magic network. your devolo Magic network, first you have to For each pairing operation, only one addi- connect it to your existing devolo Magic adapters tional adapter can be added at a time.
Mac (OS X 10.9) adapter from a network You can find the product manual, software additional information To remove a devolo Magic adapter from your net- devolo Cockpit online work and successfully restore its entire configurati- www.devolo.global/devolo-cockpit. on to the factory default settings, press the PLC/ reset button longer than 10 seconds.
Click a menu to switch di- devolo Magic 2 LAN in different ways: rectly to that menu. Using the devolo Home Network App on your smartphone or tablet, you can access the device's web interface by tapping on the corre- sponding...
Page 24
Some fields include recommended settings. Once you make a change, two icons are shown on the corresponding menu page: Recommended settings can of course be replaced with customised information. Disk icon: Your settings are being saved. devolo Magic 2 LAN...
Invalid entries 4.2.1 Overview In the Overview area, you will find information on Entry errors are either highlighted by a red border hardware and software for the devolo Magic ad- or error messages are shown. apter and network details. Buttons Click the Disk icon to save the settings for the respective web interface area.
Page 26
Magic adapters for your network along with displaying the following details: LAN – IPv4 Device ID: number of the respective devolo Magic DHCP: Display indicating whether DHCP is swit- adapter in the devolo Magic network ched on or switched off...
Enter this password for each devolo Magic adapter in the Powerline In order to use a new devolo Magic 2 LAN password field and confirm your entry with OK. your devolo Magic network, first you have to...
Page 28
Unpairing – Resetting or removing an adapter as much as possible. This option is configured by from a network default. To remove a devolo Magic adapter from your Manual compatibility mode devolo Magic network, click Leave Powerline If an interference has not been eliminated despite network.
Address, Subnetmask, Default gateway and Name server fields. Confirm your settings by clicking the Disk icon. Then, restart the devolo Magic adapter to ensure that your changes take effect. IPv6 Configuration You can access the web interface for the...
Magic adapter device password. We recommend assigning a password functions. when the installation of the devolo Magic 2 LAN System Information is complete to protect it against tampering by third parties.
Page 31
(e.g. computer) is switched on and connected to the network inter- face and if Wi-Fi is disabled. In this mode, the devolo Magic 2 LAN is not accessible over the Powerline network. As soon as the network device (e.g.
Page 32
Configuration 32 The firmware of the devolo Magic 2 LAN Manually initiate a firmware update includes the software for operating the device. If In order to manually update the firmware, necessary, devolo offers new versions on the visit the devolo website.
Page 33
33 Configuration Factory Settings To remove a devolo Magic adapter from your devolo Magic network and successfully restore its entire configuration to the factory default settings, click Factory reset. Wait until the PLC LED flashes white and then disconnect the devolo Magic adapter from the mains supply.
5.1 Technical specifications of the network, we recommend that you comply with the following "connection rules": Security 128 Bit AES Plug the devolo Magic 2 LAN directly into a Device port 1x RJ45 wall socket. Avoid using power strips. This may (Gigabit Ethernet port) impair the transmission of the PLC signals.
5.4 Warranty conditions If your devolo device is found to be defective du- ring initial installation or within the warranty peri- od, please contact the vendor who sold you the product. The vendor will take care of the repair or warranty claim for you.
Page 36
Resetting a devolo Magic adapter 14 devolo software 21 DHCP server 29 Disposal of old devices 35 Safety notes 9 Starting up a new devolo Magic network 13 Symbol description 6 Expanding an existing devolo Magic network 13 Factory default settings 14 Factory reset 14...
Need help?
Do you have a question about the Magic 2 LAN1-1 and is the answer not in the manual?
Questions and answers