●How to Reset the Repeat Number Set on the Timer to Any Desired Number
¤Align the knob of the rotary switch with
‹Press button
¿
¡
and button
simultaneously a single time. The repeat number set on the timer to any
desired number will be reset and 1 Time will be displayed.
Note that when button ¿ and button ¡ are kept depressed simultaneously for 2 seconds or longer
*
the ALL LIGHTS ON Display will appear.
The repeat number will be reset also when the ALL LIGHTS ON Display has appeared.
*
¿
(Press button
and button
¡
ALL LIGHTS ON Display
When the ALL LIGHTS ON Display appear in the
*
display appears when ¿ and ¡ are kept depressed simultaneously for more than 2 seconds.
In this case, press ¿, ¡ or C buttons to restore the normal display.
*
Even when these buttons are not pressed, the normal display will be restored after a lapse of 60 seconds
*
or more.
ALL LIGHTS ON Display
38
■HOW TO USE THE STOPWATCH
• Time can be counted in steps of 1/100 sec. up to 99 min. 59 sec. 99. (100 divisions)
When 100 minutes have elapsed a consecutive new time count from 00 min. 000
*
sec can begin.
• The split function is available.
¤Align the knob of the rotary switch with the
‹Press button
¿
to start the stopwatch.
Each time you press the ¿ button, a start and stop cycle is repeated.
*
›Press button
¿
to stop the stopwatch.
fiPress button
¡
to reset to 0 sec. (Reset)
(Start)
¡
(Reset)
40
.
¡
once simultaneously.)
¿
status, this does not indicate an error. This
position.
(Split)
¿
¡
¿
¡
(Stop)
(Split canceled)
●HOW TO SET THE TIMER KNOB TO ANY DESIRED TIME
¤Align the rotary switch with
.
‹Press button
¬
and select COUNTUP DISPLAY (△) or COUNT-DOWN DISPLAY (▼).
*
Select the display by pressing button ¬ also after the timer has started.
The time displayed is the elapsed time and the remaining time on each timer.
›Press button
¿
to start the timer.
*
Each time button ¿ is pressed the timer starts/stops.
*
The flash display indicates which timer is counting and which repeat number is in progress.
*
The TIME-UP warning function gives a previous warning and shows that the time is up for each timer for
which the TIME-UP function has been set by selecting BEEP SOUND or VIBRATION.
*
When the time set on the timer and the repeat number are over, the overtime count will start.
fiPress button ¿ to stop the timer.
flPress button ¡ to reset the timer.
Example : Suppose one needs to repeat three entire courses consisting of 2 min. 30 sec.
running exercise followed by a 30 sec. walking interval training session.
(First running start)
(First interval)
¿
(Reset)
¡
●How to Use
Normally
Button¿
→
Button¿
→
Start
→
Stop
→
●For time count
totaling
Button¿
→
Button¿
→
→
→
Start
Stop
Can be repeated as often as you
●For counting the elapsed time (split time)
in-between.
Button¿
→
Button¡
→
Start
→
Split
→
Can be repeated as often as you
●For counting the time of two
persons
Button¿
→ Button¡ → Button¿ →
Start → First person finished → Second person finished → Time of second person
Time of first person
(Second Running in Progress)
¿
(Training finished)
(Third running in progress)
Button¡
Reset
Button¿
→
Button¿
→
Button¡
→
→
Restart
Stop
Reset
wish.
Button¡
→
Button¿
→
Button¡
Split Canceled →
Stop
→
Reset
wish.
Button¡
→
→ Reset
39
Button¡
41