Table of Contents
Advertisement
The setting method
●
①
It changes to Measure Set-up Mode by pressing
②
It changes to each set-up menu by pressing
③
Set-up in each menu. (Please refer to page
④
＋
Press
Key or
⑤
Press
ENTER
⑥
Press
ENTER
Measure Set-up Mode/The Set Value Confirmation Mode
TEST Menu
(Operation tests for the
connecting/disconnecting)
ENTER
DISPLAY
Operation tests for the
connecting/disconnecting
ENTER
*1: This set-up is skipped when a "Using
VT/direct input" set-up is "yES".
*2: This set-up is skipped when a "Using
VT/direct input" set-up is "no".
*3: This set-up is skipped when a "
Phase/Wire Type" set-up is
*4: This set-up is skipped when a "
Phase/Wire Type" set-up is
*5: This set-up is skipped when a "Primary
Voltage" set-up is except "SP.".
*6: This set-up is skipped when a "Primary
Current" set-up is except "SP.".
*7: It changes to Measure Set-up Mode.
*8: It changes to The Set Value Confirmation
Mode.
1．
：
Note
Press Key
：
Press Key for
CAUTION
−
Key to set-up each setting value and complete set-up by pressing
Key after selecting Measure Set-up Menu END
Key after changes yES Display.
It changes to the following item after deciding a set-up item.
＋
Menu change.
Setting value moving down.
−
Menu change.
Setting value moving up.
It changes to a front item after deciding a setting value.
Setting value moving down. (fast forward)
Setting value moving up. (fast forward)
Setting value moving down. (fast forward)
Setting value moving up (fast forward)
It locks or releases an automatic /manual change.
Control ( "Manual ON" / "AUTO" / "Manual OFF"
each capacitor circuit is changed.
"YES" Display ： It changes to Operation Mode after
memorizing the contents of a setting.
"CANCEL" Display ： It changes to Operation Mode after
canceling the contents of a setting.
A "YES" display and a "CANCEL" displays are switched.
A "YES" display and a "CANCEL" displays are switched.
The restart of device.
This Key is effective only on a "CANCEL" Display.
"3 4W".
It locks or releases an automatic /manual change.
"3 3W".
Control ( "Manual ON" / "AUTO" / "Manual OFF" of each
capacitor circuit is changed.
Note
The Set Value Confirmation Mode
（Measure Set-up Mode）
2
seconds
Please set up Measure Set-up Menu
•
If the set-up is wrong
Set-up other items if needed.
•
When it is not set-up
50
)
Restart of device will stop measurement (a measurement display and a control
•
output) for several seconds.
Key and
ENTER
CAPACITY
＋
−
Key or
Key.
26
29
to page
)
,
after all the set-ups are completed.
Motion
2．
The example of Display of Measure Set-up Mode and
（The Set Value Confirmation Mode）
SET
f
c i l
e k
s r
1 ,
or check the contents of setting.
,
the measurement is not appropriately carried out.
,
it operates at the initial contents. (please refer to page
23
2
Key for
seconds simultaneousl y.
ENTER
Key operation
ENTER
−
＋
DISPLAY
−
＋
−
＋
LOCK/RELEASE
) of
AUTO/MANUAL
ENTER
＋
−
PHASE ＋
simultaneously
DISPLAY
LOCK/RELEASE
AUTO/MANUAL
n i
T
e h
S
t e
V
l a
e u
C
n o
r i f
m
i t a
Key.
press
press
press
press
Press for
1 second
Press for
1 second
Press for
3 seconds
Press for
3 seconds
Press for
2 seconds
press
press
press
press
Press
for 1 second
Press for
2 seconds
press
n o
M
o
e d
.
Advertisement
Table of Contents
