Page 1
PULSAR ANALOGUE QUARTZ WATCH M O D E S A N D D I S P L A Y S WITH ALARM CHRONOGRAPH TIMER T h e r e a r e t w o b u t t o n s a n d a c r o w n a s i n d i c a t e d i n t h e i l l u s t r a t i o n b e l o w .
Page 2
In each mode the hands perform the following functions. The mode changes by turning the crown at normal position c l o c k w i s e o r c o u n t e r c l o c k w i s e , a n d t h e m o d e i n d i c a t o r s h o w s t h e m o d e s e l e c t e d .
Page 3
A D J U S T I N G T H E H A N D P O S I T I O N Functions of the crown and buttons in each mode Before setting the time or calendar, or after the battery is replaced, be sure to adjust the hand position using “→Ø←”...
Page 4
T I M E S E T T I N G Pull out the crown to the first click. Press “A” or “B” repeatedly but separately to reset the stopwatch • T u r n t h e c r o w n t o s e t t h e m o d e i n d i c a t o r t o e i t h e r •...
Page 5
The minute hand may advance to the next minute. Cal. N944 has date numerals printed on the lower half of the dial P r e s s “ A ” o r “ B ” r e p e a t e d l y b u t s e p a r a t e l y t o s e t t h e h o u r , starting from the 3 o’clock.
Page 6
D U A L T I M E • Turn the crown to set the mode indicator to either “TIME” or • “TIME ”. • Turn the crown to set the mode indicator to either “TIME” or The hands move to indicate the time and calendar set previously. “TIME•...
Page 7
D u a l t i m e s e t t i n g Pull out the crown to the first click. Turn the crown clockwise or counterclockwise to set the dual time hand. * Please make sure that AM/PM of the dual time is correctly s e t .
Page 8
A l a r m e n g a g e m e n t / d i s e n g a g e m e n t Ex.) Elapsed time measured is 1 hour, 24 minutes and 37.2 seconds: •...
Page 9
To display the finish time of the second 2 . A c c u m u l a t e d e l a p s e d t i m e competitor Press “B”. m e a s u r e m e n t To reset to “0”...
Page 10
Ex.) N o t e s : • Even if the mode is changed from “CHRONO” to another while the stopwatch is running, it continues measurement. However, Elapsed time i f “ → Ø ← ” m o d e i s s e l e c t e d a n d t h e c r o w n i s p u l l e d o u t , t h e measurement is canceled and the hands return to “0”...
Page 11
T i m e r s e t t i n g 1. If the timer has been set previously, press “B”. The minute hand moves to indicate the time set previously. • Turn the crown to set the mode indicator to “TIMER”. The hour, minute, 1/10 second and timer second hands return If you want to change the set time, or the timer has not been to the 12 o’clock position.
Page 12
N o t e s : NECESSARY OPERATION AFTER BATTERY CHANGE • In order to save the energy, until the remaining time becomes When the battery is replaced, the time information stored in the l e s s t h a n 5 m i n u t e s , t h e t i m e r s e c o n d h a n d s t o p s a t t h e 1 2 built-in IC and the time indicated by the hands do not correspond o’clock position and the 1/10 second hand shows special swing w i t h e a c h o t h e r .
Page 13
• Have your Pulsar watch checked by a PULSAR DEALER periodi- c a l l y t o b e s u r e t h a t t h e c a s e , b u t t o n s , c r o w n , g a s k e t , c r y s t a l If your watch is water resistant, “WATER RESISTANT”...
Need help?
Do you have a question about the N944 and is the answer not in the manual?
Questions and answers