Related Manuals for YOKOGAWA YEW 80 Series
Summary of Contents for YOKOGAWA YEW 80 Series
- Page 1 User’s Manual Model SIND (Style S) Integrator IM 01B04M01-02E 10th Edition Y okogawa Electric Corporation...
-
Page 3: Table Of Contents
Contents Chapter 1 Introduction Inspection ..........................1-2 Documentation Conventions ....................1-3 Notice ..........................1-4 Compatibility with Previous Models ..................1-5 Chapter 2 General Standard Specifications ......................2-2 Model and Suffix Codes ......................2-3 Accessories .........................2-4 Chapter 3 Installation External Wiring ........................3-2 Connecting the SICD Counter .....................3-3 Connecting a Third-party Counter .................. - Page 4 Blank...
-
Page 5: Chapter 1 Introduction
Chapter 1 Introduction Introduction This manual describes the functions and operations of the SIND Integrator. ● Intended Readers This manual is intended for personnel in charge: • Installation and wiring • Instrumentation and setup of the function • Operation and monitoring of the controller •... -
Page 6: Inspection
Check the package contents against the list below. If anything is missing or damaged, immediately contact the sales office from which you purchased the product or your nearest Yokogawa representative. • SIND Integrator ....................1 • Integrating ratio label (Parts No.:L4040JA) ............1 •... -
Page 7: Documentation Conventions
The product has a QR Code pasted for efficient plant maintenance work and asset information management. It enables confirming the specifications of purchased products and user’s manuals. For more details, please refer to the following URL. https://www.yokogawa.com/qr-code QR Code is a registered trademark of DENSO WAVE INCORPORATED. IM 01B04M01-02E... -
Page 8: Notice
• Yokogawa does not make any warranties regarding the product except those mentioned in the WARRANTY that is provided separately. • Yokogawa assumes no liability to any party for any loss or damage, direct or indirect, caused by the use or any unpredictable defect of the product. -
Page 9: Compatibility With Previous Models
Compatibility with Previous Models Compatibility with style A ● Operation and settings differ from previous model (styles A). Please read this document carefully before operating the product. ● Before installing this product in a system or plant, you must check the jumper settings and parameters described in chapter 5, “Settings.”... - Page 10 Blank...
-
Page 11: Chapter 2 General
*1: The modular jack conversion adapter (E9786WH) is required for connecting the JHT200 Handy Terminal to the Integrator. The 5 pin-connector type communication cable (F9182EE) and modular jack conversion adapter (E9786WH) is required for connecting the BT200 BRAIN Terminal of YOKOGAWA ELECTRIC Corporation F0201.ai... -
Page 12: Standard Specifications
Standard Specifications Please see the General Specifications (GS 01B04M01-02E) at the end of this manual. IM 01B04M01-02E... -
Page 13: App
Model and Suffix Codes Model Suffix Style Optional Description Codes Suffix Codes SIND Integrator Output Proportional output (*1) Square-root output Indication setter Not provided Provided Style Code Style S (*2) (*3) Option Codes /NHR Without rack case /FBP Power supply fuse bypass /LOCK Power supply plug with lock /WSW... -
Page 14: Accessories
Accessories Integrating ratio label: 1 sheet IM 01B04M01-02E... -
Page 15: Installation
Chapter 3 Installation Installation For details of the installation procedure and wiring precautions, refer to the instruction manual “Installation of Rack-Mounted Instruments” (IM 1B4F2-01E). IM 01B04M01-02E... -
Page 16: External Wiring
External Wiring (a) All cable ends must furnished with crimp-on type solderless lugs (for 4mm screws). (b) Draw out the internal unit from the rack case. (c) Connect the cables to the correct terminals referring to Figure 3-1. (d) Return the internal unit into the rack case after completing the wiring. (e) Always return the terminal block cover to its original position after completing the wiring. -
Page 17: Connecting The Sicd Counter
Connecting the SICD Counter Up to two SICD counters can be connected. (See Figure 3-2.) If the input pulse specifications are the same as the SICD, a third-party electromagnetic counter (24 V DC, 150 mA or less) can also be connected. When a counter other than a SICD is used, connect a diode in parallel with the counter coil to prevent surge voltage. -
Page 18: Connecting A Third-Party Counter
Connecting a Third-party Counter A third-party counter can be driven by an external power supply, and pulse signals can be generated for output to a computer, for example. 3.3.1 Attaching an External Power Supply Specifications of connectable counter Applied voltage: 30 V DC or less Minimum pulse ON/OFF time: 30 ms(*) each or less *: Long response time (60 ms or less) counters can also be connected by shorting the A and C terminals. - Page 19 3.3 Connecting a Third-party Counter Applicable Cables (1) Signal circuit wiring • Cross-sectional area of the cable conductor: 0.5 to 0.75 mm • Examples of applicable cables: 600 V PVC insulated cable (IV) stranded wires (JIS C 3307); PVC insulated cable for electrical apparatus (KIV) stranded wires (JIS C 3316); Heat-resistant vinyl-insulated cable (UL style 1007) (2) Power supply wiring •...
- Page 20 Blank...
-
Page 21: Principle Of Operation
Chapter 4 Principles of Operation Principle of Operation Input signals are converted to digital data by the A/D conversion circuit after passing through the input processing circuit. The resulting digital data is processed (square root calculation, input scaling, integrating pulse calculation, etc.) by the microcomputer, and turns the output transistor N/OFF by the pulse output circuit. - Page 22 4.1 Principle of Operation Input signals undergo A/D conversion and compensation before being converted to data at INPUT1. On the SIND-20x, input signals also undergo square root calculation. The low input cutoff function is provided for both square root calculation and proportional calculation (w/out square root calculation).
-
Page 23: Chapter 5 Setting
Chapter 5 Setting Setting Items to Confirm before Start of Operation Before you start operation, inspect and confirm the following items: (1) Draw out the internal unit from the rack case, and make sure that the specified fuses are properly mounted in the fuse holders at the rear of the internal unit. -
Page 24: Names Of Components
Names of Components The following shows the names of SIND components. Integrating ratio indicator lamp (PPH) Low input cutoff indicator lamp (LCT) Display setter Data digit feed key Parameter selection key Data change key Data setting fix key Tag plate BRAIN connector (w / cover) Key setting enable switch... -
Page 25: Setting Jumper
Setting Jumper SIND is provided with a Parameter Write Protect (W.P.) jumper. When this jumper is set to ON, changing of parameters by the key switches and Handy Terminal is disabled. “LOC” will be displayed on the display setter if the “→” switch is pressed with the PPH or LCT parameter displayed on the display setter. -
Page 26: Setting Of Parameters
*1: The modular jack conversion adapter (E9786WH) is required for connecting the JHT200 Handy Terminal to the Alarm Unit. The 5 pin-connector type communication cable (F9182EE) and modular jack conversion adapter (E9786WH) is required for connecting the BT200 BRAIN Terminal of YOKOGAWA ELECTRIC Corporation. 5.3.1... - Page 27 5.3 Setting of Parameters Indicator out mode is entered if no key switch is Displays previous parameter. operated for 30 minutes when display mode Displays next parameter. parameter is "OFF". Indicator out mode Display mode Display mode is returned to when any key switch is pressed.
- Page 28 5.3 Setting of Parameters Setting Parameters Display the desired parameter (integrating ratio or low-cut point), and follow the procedure below to change its setting. (1) Input value (60.00) is displayed at power ON. Press the key. The PPH lamp lights, and the integrating ratio is displayed.
- Page 29 5.3 Setting of Parameters Display at Power ON The model with display setter displays REV NO. (revision number of software for SIND for about 2 seconds after power ON. Example of display (REV NO.10) LOC Display When “LOC” is displayed, this indicates that parameter settings cannot be changed. (The Parameter Write Protect jumper on the main board is set to “ON”.) To cancel the “LOC”...
-
Page 30: Setting Of Parameters Using Handy Terminal
5.3 Setting of Parameters 5.3.3 Setting of Parameters Using Handy Terminal For details of operation and adjusting procedures of JHT200 Handy Terminal, refer to the instruction manual “JHT200 Handy Terminal” (IM 77J50H01-01EN). <Connection> Cable of 5-pin connector type (F9182EE) BRAIN connector JHT200 Handy Terminal Adapter for modular jack (E9786WH) F0504.ai Figure 5-7 Connecting the Handy Terminal... -
Page 31: Parameter List
Parameter List BRAIN communication parameters for SIND are as follows. On the SIND-x04, only the input value can be displayed, and integrating ratio and lowcut point can be displayed and set on the display setter on the front panel. Other, parameters are displayed and set using the Handy Terminal. - Page 32 5.4 Parameter List Parameter Name Symbol Description Setting Range Factory-set Display Value Conditions Setting Parameters SET(I/O) Tag Number 1 TAG NO.1 8 alphanumerics can be Displayed on all entered. Tag Number 2 TAG NO.2 8 alphanumerics can be entered. Comment 1 COMMENT1 8 alphanumerics can be entered.
- Page 33 5.4 Parameter List Parameter Name Symbol Description Setting Range Factory-set Display Value Conditions Setting Alarm SET(ALM) Parameters Zero Adjustment ZERO ADJ1 Performs zero adjustment (0% side) on input 1. Displayed on (Input 1) n.nnn V RST n.nnn V INC n.nnn V HINC n.nnn V HDEC n.nnn V DEC n.nnn indicates the current input value.
- Page 34 Blank...
-
Page 35: Chapter 6 Maintenance
Chapter 6 Maintenance Maintenance This chapter describes the calibration procedures that can be done in the instrument room or service shop. IM 01B04M01-02E... -
Page 36: Test Equipment
Test Equipment For efficient maintenance of this integrator, it is recommended that the user have the following test equipment manufactured by Yokogawa or their equivalent. ● DC Voltage/Current Standard, Yokogawa GS200 or the equivalent……..1 set ● , Yokogawa …................ 1 set... -
Page 37: Check Of I/O
(c) Turn on SIND with a devices connected, and allow 5 minutes for the system to warm up. 0 0 1 2 3 4 SICD Counter Voltage/Current Standard 2 4 6 Power Yokogawa GS200 or Supply the equivalent F0602.ai Figure 6-2 Wiring Diagram IM 01B04M01-02E... -
Page 38: Checking Procedure
6.2 Check of I/O 6.2.2 Checking Procedure (a) Set the integrating ratio (PPH) on the SIND integrator to 9000 pph. (b) Apply a voltage of 0 V DC to the input, and reset the integration value on the SICD counter. (c) Apply the input signal in a stepped manner for 400 seconds while monitoring the time, and integrate to 5 V DC. -
Page 39: List Of Replaceble Parts
List of Replaceble Parts Contact YOKOGAWA’s sales office or sales representative when replacing the spare parts. Part Name Part Number Recommended Reference replacement period Fuse S9510VK Approx. 3 years If the fuse breaks or if the replacement period elapses, please have the item replaced. - Page 40 Blank...
-
Page 41: Chapter 7 Troubleshooting
Chapter 7 Troubleshooting Troubleshooting If any fault occurs in the instrument, note the symptoms and follow Section 7.1. IM 01B04M01-02E... -
Page 42: Action In Fault Condition
*2: STATUS error code is to be the addition display (hexadecimal number) when two errors or more occur. *3: If errors continue even when the input is within the range, the input circuit is broken. Contact YOKOGAWA's sales office or sales representative. IM 01B04M01-02E... -
Page 43: Chapter 8 Power Supply Terminal Connections (Option /Tb, /A2Tb, And /Rek)
Chapter 8 Power Supply Terminal Connections (Option /TB, /A2TB, and /REK) Power Supply Terminal Connections (Options /TB, /A2TB, and /REK) If you specify the terminal block to which the power source is directly connected (option codes: /TB, /A2TB, and /REK), the external wiring to the terminal block is necessary; therefore, drawing out the internal unit requires previous turning off of the power source and disconnection of the wiring from the terminal block. -
Page 44: External View And Names Of Components
External View and Names of Components Output Terminal Block Output Terminal Cover Power Fuse Power Terminal Cover Input Terminal Block Power Terminal Power and Ground Terminal connection (Connection screw: M4) Symbol Description Input Terminal Cover + Power supply Ground Figure 8-1 Names of Parts and Power Terminal IM 01B04M01-02E... -
Page 45: Power Supply And Ground Wiring
Power Supply and Ground Wiring (1) All cable ends must be furnished with crimp-on type solderless lugs (for 4 mm screws). (2) Examples of applicable cables: Cross-sectional area of the cable conductor: 2.0 mm For the power supply, use cable having a cross-sectional area of at least 1.25 mm Applicable cable: 600 V vinyle insulated cable (IV) stranded wires, conforming to JIS C3307. - Page 46 Blank...
-
Page 47: General Specifications
(SIND-04), input indication can be displayed and integrating ratio and low input cut off can be displayed / set on the front panel. The BT200 BRAIN Terminal of YOKOGAWA Electric Corporation can also be connected. n MOUNTING AND APPEARANCE... - Page 48 Mount to same line with EK series rack /TB: With power supply terminal /A2TB: 220V version with power supply terminal /A2ER: 220V version with power supply plug All Rights Reserved. Copyright © 2002, Yokogawa Electric Corporation GS 01B04M01-02E Sep.17, 2019-00...
- Page 49 When a counter other than SICD is used, connect a surge voltage protective diode in parallel with the counter coil. Terminal Description Designation Input (1 to 5 V DC) All Rights Reserved. Copyright © 2002, Yokogawa Electric Corporation GS 01B04M01-02E Sep.17, 2019-00...
- Page 50 (Connection screw: M4) Symbol Description + Power supply Ground Trigonometry Unit: mm General tolerance = ±(value of tolerance class IT18 based on JIS B 0401-2016) / 2 F03.ai All Rights Reserved. Copyright © 2002, Yokogawa Electric Corporation GS 01B04M01-02E Sep.17, 2019-00...
- Page 51 (Connection screw: M4) Symbol Description + Power supply Ground Trigonometry Unit: mm General tolerance = ±(value of tolerance class IT18 based on JIS B 0401-2016) / 2 F04.ai All Rights Reserved. Copyright © 2002, Yokogawa Electric Corporation GS 01B04M01-02E Sep.17, 2019-00...
- Page 52 *3:/FBP, /A2TB, and /A2ER cannot be specified together. n ACCESSORIES Integrating ratio label: 1 sheet n ORDERING INSTRUCTIONS 1. Model and suffix codes and option codes, if necessary All Rights Reserved. Copyright © 2002, Yokogawa Electric Corporation GS 01B04M01-02E Sep.17, 2019-00 Subject to change without notice.
- Page 53 : IM 01B04M01-02E Jul. 2002/7th Renewal Mar. 2003/8th Correct May 2004/9th Change of the company name. Oct 2019/10th Change of the style number. Written by Yokogawa Electric Corporation Published by Yokogawa Electric Corporation 2-9-32 Nakacho, Musashino-shi, Tokyo 180-8750, JAPAN...
- Page 54 3F Tower D Cartelo Crocodile Building, No.568 West Tianshan Road, Shanghai 200335, CHINA Phone : 86-21-62396262 Fax : 86-21-62387866 YOKOGAWA ELECTRIC KOREA CO., LTD. (Yokogawa B/D, Yangpyeong-dong 4-Ga), 21, Seonyu-ro 45-gil, Yeongdeungpo-gu, Seoul, 07209, KOREA Phone : 82-2-2628-6000 Fax : 82-2-2628-6400 YOKOGAWA ENGINEERING ASIA PTE. LTD.