Table of Contents

Advertisement

www.ti.com
User's Guide
AWR1843AoP EVM User's Guide
The AWR1843AOPEVM from Texas Instruments is an easy-to-use evaluation board for the AWR1843AOP
mmWave sensing device, with direct connectivity to the MMWAVEICBOOST and DCA1000EVM development
kits. This EVM contains everything required to start developing software for on-chip C67x DSP core and low-
power ARM® Cortex®-R4F controllers.
Started........................................................................................................................................................................3
Features......................................................................................................................................................................3
Contents........................................................................................................................................................................3
2 Hardware.................................................................................................................................................................................
Diagram....................................................................................................................................................................5
2.2 PCB Storage and Handling Recommendations.................................................................................................................
2.3 Heat Sink and Temperature...............................................................................................................................................
2.4 AWR1843AOPEVM Antenna.............................................................................................................................................
2.5 Switch Settings.................................................................................................................................................................
2.6
LEDs.................................................................................................................................................................................11
2.7
Connectors.......................................................................................................................................................................13
2.10 PC Connection...............................................................................................................................................................
2.11 Power Supply Optimization............................................................................................................................................
3.1
Hardware..........................................................................................................................................................................27
3.3 LDO Bypass Requirement...............................................................................................................................................
4 References............................................................................................................................................................................
Figure 2-1. AWR1843AOPEVM Top View...................................................................................................................................
Figure 2-3. Block Diagram of the AWR1843AOPEVM................................................................................................................
Figure 2-5. Heat Sink CAD Drawing............................................................................................................................................
Placement.................................................................................................................................................7
Figure 2-11. AWR1843AOPEVM Switches................................................................................................................................
Figure 2-14. USB Connector (J1)..............................................................................................................................................
Figure 2-15. DCA1000 HD Connector (J11)..............................................................................................................................
Figure 2-16. MMWAVEICBOOST HD Connector (J2)...............................................................................................................
Figure 2-17. I2C Connector (J3)................................................................................................................................................
Figure 2-18. BT/JTAG Connector (J7).......................................................................................................................................
SPRUIX8 - MARCH 2021
Submit Document Feedback
ABSTRACT

Table of Contents

Scheme...............................................................................................................................20
Mode........................................................................................................20
Tools.........................................................................................................................................27
Code..........................................................................................................27
List of Figures
View..............................................................................................................................5
Temperature..................................................................................................................6
Array......................................................................................................8
GHz)..................................................................................................................9
GHz)................................................................................................................10
PCB......................................................................................................................................12
(J5).....................................................................................................................................13
Copyright © 2021 Texas Instruments Incorporated
PCB..............................................................................................8
Table of Contents
AWR1843AoP EVM User's Guide
4
6
6
8
11
24
24
27
28
4
5
7
11
14
15
16
17
18
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AWR1843AOP EVM and is the answer not in the manual?

Questions and answers

Summary of Contents for Texas Instruments AWR1843AOP EVM

  • Page 1: Table Of Contents

    AWR1843AoP EVM User’s Guide ABSTRACT The AWR1843AOPEVM from Texas Instruments is an easy-to-use evaluation board for the AWR1843AOP mmWave sensing device, with direct connectivity to the MMWAVEICBOOST and DCA1000EVM development kits. This EVM contains everything required to start developing software for on-chip C67x DSP core and low- power ARM®...
  • Page 2 Table 2-7. J8, J10 Pin Assignment............................Table 2-8. Pin Mux Settings............................... Table 2-9. SOP Switch Settings..............................20 Trademarks All trademarks are the property of their respective owners. AWR1843AoP EVM User’s Guide SPRUIX8 – MARCH 2021 Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated...
  • Page 3: Getting Started

    TI provides sample demo codes to easily get started with the AWR1843AOP evaluation module (EVM) and to experience the functionality of the AWR1843AOP radar sensor. For details on getting started with these demos, see www.ti.com/tool/mmwave-sdk. SPRUIX8 – MARCH 2021 AWR1843AoP EVM User’s Guide Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated...
  • Page 4: Hardware

    77 to 81 GHz mmWave sensing for form-factor deployment and testing • Functional and flashing SOP Mode • Emulator USB port for user UART and Data COM ports AWR1843AoP EVM User’s Guide SPRUIX8 – MARCH 2021 Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated...
  • Page 5: Block Diagram

    The Breakaway board sections contain the 60-pin Samtec connector for interfacing with the DCA1000 and MMWAVEICBOOST. Figure 2-3. Block Diagram of the AWR1843AOPEVM SPRUIX8 – MARCH 2021 AWR1843AoP EVM User’s Guide Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated...
  • Page 6: Pcb Storage And Handling Recommendations

    The CAD drawing for the heat sink is shown in Figure 2-5. AWR1843AoP EVM User’s Guide SPRUIX8 – MARCH 2021 Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated...
  • Page 7: Figure 2-5. Heat Sink Cad Drawing

    Hardware Figure 2-5. Heat Sink CAD Drawing Application of the heat sink is shown in Figure 2-6. Figure 2-6. Heat Sink Placement SPRUIX8 – MARCH 2021 AWR1843AoP EVM User’s Guide Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated...
  • Page 8: Awr1843Aopevm Antenna

    EVM is mounted on the provided mounting stand, the antenna is in the elevation orientation relative to the scene. Figure 2-8. Orientation of the AWR1843AOP Relative to the PCB AWR1843AoP EVM User’s Guide SPRUIX8 – MARCH 2021 Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated...
  • Page 9: Figure 2-9. Measured Azimuthal Radiation Pattern For All Tx To Rx Pairs

    Figure 2-9. Measured Azimuthal Radiation Pattern for All Tx to Rx Pairs (Corner Reflector Placed at 4.5 Meters with a 1.75-GHz Bandwidth Chirp Starting at 77.75 GHz) SPRUIX8 – MARCH 2021 AWR1843AoP EVM User’s Guide Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated...
  • Page 10: Figure 2-10. Measured Elevation Radiation Pattern For All Tx To Rx Pairs

    Figure 2-10. Measured Elevation Radiation Pattern for All Tx to Rx Pairs (Corner Reflector Placed at 4.5 Meters with a 1.75-GHz Bandwidth Chirp Starting at 77.75 GHz) AWR1843AoP EVM User’s Guide SPRUIX8 – MARCH 2021 Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated...
  • Page 11: Switch Settings

    GPIO2 LED, illuminates when GPIO2 is logic-1 USB to UART enumeration LED NRST LED, illuminates when NRST is pulled low CC2642R GPIO6 LED, illuminates when GPIO6 is logic-1 SPRUIX8 – MARCH 2021 AWR1843AoP EVM User’s Guide Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated...
  • Page 12: Figure 2-12. Location Of Leds On Pcb

    Hardware www.ti.com Figure 2-12. Location of LEDs on PCB AWR1843AoP EVM User’s Guide SPRUIX8 – MARCH 2021 Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated...
  • Page 13: Connectors

    After the 5-V power supply is provided to the EVM, TI recommends pressing the NRST switch (SW2) one time to ensure a reliable boot-up state. Figure 2-13. 5-V Power Connector (J5) SPRUIX8 – MARCH 2021 AWR1843AoP EVM User’s Guide Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated...
  • Page 14: Figure 2-14. Usb Connector (J1)

    UART • MSS logger UART (can be used to get MSS code logs on the PC) Figure 2-14. USB Connector (J1) AWR1843AoP EVM User’s Guide SPRUIX8 – MARCH 2021 Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated...
  • Page 15: Figure 2-15. Dca1000 Hd Connector (J11)

    LVDS_FRCLKN DMM_DP5 DMM_DP6 No Connection DMM_DP7 No Connection No Connection No Connection No Connection No Connection No Connection No Connection No Connection LVDS_CLKP SPRUIX8 – MARCH 2021 AWR1843AoP EVM User’s Guide Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated...
  • Page 16: Figure 2-16. Mmwaveicboost Hd Connector (J2)

    No Connection No Connection No Connection No Connection No Connection DMM_SYNC No Connection DMM_CLK AR_NRESET MMWAVEICBOOST PGOOD SPI_HOSTINTR TDO_SOP0 MSS_LOGGER SPI_CS1 SPI_CLK AR_SYNC_IN AWR1843AoP EVM User’s Guide SPRUIX8 – MARCH 2021 Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated...
  • Page 17: Figure 2-17. I2C Connector (J3)

    The I2C bus along with the 3.3-V supply and GND are brought out on the I2C connector (J3). Figure 2-17. I2C Connector (J3) Table 2-5. J3 Pin Assignment Pin Number Description 3.3 V I2C_SCL I2C_SDA SPRUIX8 – MARCH 2021 AWR1843AoP EVM User’s Guide Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated...
  • Page 18: Figure 2-18. Bt/Jtag Connector (J7)

    Figure 2-18. BT/JTAG Connector (J7) Table 2-6. J7 Pin Assignment Pin Number Description Bluetooth UART_RX Bluetooth UART_TX Bluetooth NRESET JTAG_TDI JTAG_TDO JTAG_TCK 3.3V JTAG_TMS AWR1843AoP EVM User’s Guide SPRUIX8 – MARCH 2021 Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated...
  • Page 19: Figure 2-19. Can Connectors (J8, J10)

    CAND-FD transceivers (TCAN1042HGVDRQ1). These signals can be directly wired to the CAN bus. Figure 2-19. CAN Connectors (J8, J10) Table 2-7. J8, J10 Pin Assignment Pin Number Description CAN_L CAN_H SPRUIX8 – MARCH 2021 AWR1843AoP EVM User’s Guide Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated...
  • Page 20: Awr1843Aopevm Muxing Scheme

    EVM to the DCA1000 EVM on the J11 connector. For more details about the DCA1000 EVM and its features, refer to the DCA1000 EVM User's Guide. AWR1843AoP EVM User’s Guide SPRUIX8 – MARCH 2021 Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated...
  • Page 21: Figure 2-20. Switch Configuration For Modular Mode (Functional)

    Figure 2-20. Switch Configuration for Modular Mode (Functional) Figure 2-21. Switch Configuration for Bluetooth Mode (Functional) For higher power application ensure the USB J1 is connected before connecting USB J5. SPRUIX8 – MARCH 2021 AWR1843AoP EVM User’s Guide Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated...
  • Page 22: Figure 2-22. Awr1843Aopevm Mounted On Mmwaveicboost

    This mode enables access to debugging tools available on the MMWAVEICBOOST such as the JTAG, ADC capture, CAN, LaunchPad connector, and so forth. Figure 2-22. AWR1843AOPEVM Mounted on MMWAVEICBOOST AWR1843AoP EVM User’s Guide SPRUIX8 – MARCH 2021 Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated...
  • Page 23: Figure 2-23. Switch Configuration For Mmwaveicboost Mode

    For mounted mode, the UART should be routed to the 60-pin connector. The SOP settings are controlled by the SOP switches on the AWR1843AOPEVM. Set up the device as shown in Figure 2-25. SPRUIX8 – MARCH 2021 AWR1843AoP EVM User’s Guide Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated...
  • Page 24: Pc Connection

    (which may come at the expense or poorer 4-Mhz filtering). Typically, setting issues will show up as a transient in the start of the time domain plot as shown below. AWR1843AoP EVM User’s Guide SPRUIX8 – MARCH 2021 Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated...
  • Page 25: Figure 2-27. Time Domain Plot With Transient Ringing On 1.0-V Supply

    BLM18KG121TH1D part. Further optimizations can be made by replacing C75, and C111 with the GCM21BD70J226ME36L part and C113 and C121 with the GCM21BR71A106KE22L part. SPRUIX8 – MARCH 2021 AWR1843AoP EVM User’s Guide Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated...
  • Page 26: Figure 2-28. Secondary Lc Filter On The Awr1843Aopevm

    Hardware www.ti.com Figure 2-28. Secondary LC Filter on the AWR1843AOPEVM AWR1843AoP EVM User’s Guide SPRUIX8 – MARCH 2021 Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated...
  • Page 27: Design Files And Software Tools

    AWR_RF_LDO_BYPASS_SB API. To enable the RF LDO Bypass and PA LDO I/P Disable through the API, issue an ar1.RfLdoBypassConfig(0x3) command. Figure 3-1. LDO Bypass Enable SPRUIX8 – MARCH 2021 AWR1843AoP EVM User’s Guide Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated...
  • Page 28: References

    References www.ti.com 4 References DCA1000EVM Data Capture Card User’s Guide MMWAVEICBOOST User’s Guide AWR1843AoP EVM User’s Guide SPRUIX8 – MARCH 2021 Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated...
  • Page 29 TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for TI products.IMPORTANT NOTICE Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2021, Texas Instruments Incorporated...

Table of Contents