Table of Contents
Advertisement
Quick Links
GIR-3000W
Instruction Manual
Headquarters / Engineering research laboratory :
23 Gunpo Advance d Industry 1-ro(Bugok-dong), Gunpo-si, Gyeonggi-do
Tel +82-31-490-0800 Fax +82-31-490-0801
Yeongnam business office / Plant :
55 Gonghangap-gil 85beon-gil, Gangseogu, Busan Metropolitan City
Tel +51-973-8518 Fax +51-973-8519
E-mail : info@gastron.com
www.gastron.com
Read in detail for correct use.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for GASTRON GIR-3000W
Summary of Contents for GASTRON GIR-3000W
- Page 1 Headquarters / Engineering research laboratory : 23 Gunpo Advance d Industry 1-ro(Bugok-dong), Gunpo-si, Gyeonggi-do Tel +82-31-490-0800 Fax +82-31-490-0801 Yeongnam business office / Plant : 55 Gonghangap-gil 85beon-gil, Gangseogu, Busan Metropolitan City Tel +51-973-8518 Fax +51-973-8519 E-mail : info@gastron.com www.gastron.com Read in detail for correct use.
- Page 2 Gas detectors satisfying customers. From now on, solve all anguishes concerning Gas detector with the products of Gastron Co. Ltd, We Gastron Co. will take a responsibility and give you satisfaction.
-
Page 3: Table Of Contents
5.4. Configuration of Relay terminal and communication terminal ········································································ 5.4.1. Configuration of terminal ··················································································································· 10.3. Upon coupling of warning light ······················································································································· 10.4. GIR-3000W Remote Type ·································································································································· 5.4.2. Setting for Relay mode························································································································ 5.4.3. Setting for RS485 MODBUS ··············································································································· 11. Notes before installation 5.5. -
Page 4: Overview
Instruction Manual 06_07 GIR-3000W infrared Gas detector has been developed to prevent accidents beforehand by detecting various leaked 3.1. Basic Specifications gases generated in industry fields such as plants producing or using combustible gas, carbon monoxide, carbon dioxide, ITEMS SPECIFICATION gas storage place, manufacturing processes, etc. -
Page 5: Electrical Specifications (Standard Type)
Rated 1.0 A @ 30VDC or 0.5 A @ 125 VAC Power CVVS or CVVSB with shield Wiring requirement Analog CVVS or CVVSB with shield RS485 STP(Shielded Twisted Pair) [Figure 2. Components of GIR-3000W Transmitter] Analog 2500m Signal transmission distance (Cable Connection Length) RS485 1000m ITEMS... -
Page 6: Components Of Infrared Sensor
Warning Light Connecting connector when the warning light is used(Optional) Connector Calibration port Inlet for calibration gas upon gas calibration Filter fixing screw Screw for fixing of filter [Table 1. Components of GIR-3000W] [Table 2 Description on components of GIR-3000W]... -
Page 7: Components Of Gtl-100
4.4. Description on LAMP function ■ In the case of Normal state, green LED is lighted for the warning light, and Buzzer does not sound. ■ When signals of Alarm-1 are received, red LED blinks at an interval of 1 second, and Buzzer sounds at an interval of 1 second. ■ When signals of Alarm-2 are received, red LED is lighted, and Buzzer sounds continuously. ■ When Trouble signals are received, yellow LED is lighted, and Buzzer does not sound. [Figure 4. Components of GIR-3000W Lamp] NAME DESCRIPTION Explosion-proof CASE made of plastic material, with a transparent window that disperses LED FRONT CASE light to outside. -
Page 8: Installation
3~4 turns clockwise by using a hexagonal wrench (M2). screw (M4) When Cover is separated, LCD unit is displayed. Figure when infrared Sensor(Detector) is mounted [Figure 3. Components of GIR-3000W Sensor] NAME DESCRIPTION [Figure 3. Slotted set screw] CN12 Power & Output Signal Terminal 4~20mA Source / Sink selection jumper(ON: Source Type, OFF: Sink Type) ■ When Cover is separated, separate Display Parts in the... -
Page 9: Configuration Of Power Supply And 4-20Ma Terminal
GIR-3000W 5. Installation 5. Installation www.gastron.com Instruction Manual 16_17 5.3. Configuration of power supply and 4-20mA terminal 5.3.1. Wire connection diagram of driving method for 4~20mA Source ■ <Warning - Conduct operation after shutting off the power supply upon connection of power supply terminal.> ■ When Display Parts are separated, Terminal Block in Main PCB can be seen as show in the following figure, ■ Connect 4-20mA Signal terminal on PLC side to which is separated from Main PCB when held by hand and pulled up. -
Page 10: Wire Connection Diagram Of Driving Method For 4~20Ma 3Wire Sink
GIR-3000W 5. Installation 5. Installation www.gastron.com Instruction Manual 18_19 5.3.3. Wire connection diagram of driving method for 5.4.2. Setting for Relay mode 4~20mA 3Wire Sink ■ Connect 4-20mA Sink output (+) terminal on PLC side to VISO terminal, and (-) terminal to (24V DC) (-) terminal. Connect 'mA' terminal of GIR-3000 to 'GND' terminal. Then connectturn the J1 Jumper OFF. [Figure 13. Setting for Relay Mode] [Figure 11.Configuration of 4-20mA 3Wire Sink]... -
Page 11: Configuration Of Sensor Connecting Terminal
GIR-3000W 5. Installation 5. Installation www.gastron.com Instruction Manual 20_21 5.5. Configuration of sensor-connecting terminal 5.6. Configuration of Remote Type connection ■ IR sensor module (to be referred to as GSA920A hereafter) is connected to the transmitter by using CN No.10 terminal ■ To remotely configure GSA920A, the sensor is installed by using Junction Box(GDH-1010) of the following form, and connection is made to GIR-3000 transmitter by using component terminal inside Junction Box. [Figure 14. Sensor-connecting Terminal] TER. -
Page 12: Length Of Installed Cable
- Measured GAS NAME is displayed in the 1st row, while current measured value and unit are displayed in the 2nd row. # [ CH4 ] ※ During communication with the sensor unit, '#'character is displayed in the left-side part of GAS NAME. 0]%LEL ※ During HART communication or 485 communication, '*' character is displayed in the left-side part of [Figure 17. Calculation of length of installed cable for GIR-3000W] the 1st row. *#[ CH4 ] ※ When ENG. Mode is turned ON, the current temperature is displayed in the left-side part of the 2nd row. 0]%LEL ■ Installation length of power supply cable according to cable classification is as shown in the following table. -
Page 13: Operation Flow
50% of Full Scale [CH4] SPAN GAS 000 [ SPAN PROCESSING [SUCCESS / FAIL ] CALIBRATION DATA ALARM OPERATING [AUTO/MANUAL] AUTO [Figure 18. Configuration of GIR-3000W mode] ALARM RELAY TYPE DE-ENERGIZED/ENERGIZED DE-ENERGIZED FAULT RELAY TYPE DE-ENERGIZED/ENERGIZED DE-ENERGIZED ■ Operation key for control of sensor system mode is defined as follows. ALARM1 TYPE SEL. -
Page 14: System Mode
GIR-3000W 6. Sensor operation Flow 7. System Mode www.gastron.com Instruction Manual 26_27 6.4. Menu Configuration Table 7.1. PROGRAM MODE LEVEL2 - Enter in the Level1 mode after Password checking. LEVEL1 DEFAULT PROGRMAMMABLE NAME PARAMETER - "Select PROGRAMMABLE MODE by touching "↑" key or "↓" key. MODE ALARM1 TIME SET [0~60] SEC - When Function key is touched at this time, PROGRAMMABLE MODE Level2 sub menu is entered in. -
Page 15: Calibration Mode
GIR-3000W 7. System Mode 7. System Mode www.gastron.com Instruction Manual 28_29 7.2. CALIBRATION MODE 7.2.2. Span Calibration ■ Due to the characteristics of Gas detector, a stabilization time of at least about 30 minutes is required after supply of SPAN CALIBRATION - Span Calibration Mode is entered in if FUNC key is touched when it is [YES] by touching "↑" key or "↓" key. power, and the management criteria may be varied with field conditions.. [YES] - Span calibration is automatically executed if FUNC key is touched when the measured value is [CH4] SPAN GAS 7.2.1. -
Page 16: Alarm Mode
GIR-3000W 7. System Mode 7. System Mode www.gastron.com Instruction Manual 30_31 7.3. ALARM MODE 7.3. ALARM MODE - Enter in Level1 mode after password checking. - Mode for setting the direction for operation of Alarm2 with "INCREASE" or "DECREASE" displayed ALARM2 TYPE SEL. ALARM PROGRAM - Select ALARM MODE by touching "↑"key or "↓"key. [INCREASE ] whenever "↑"key or "↓"key is touched. MODE - ALARM MODE Level2 is entered in when Function key is touched at this time. -
Page 17: Troubleshooting
GIR-3000W 8. Troubleshooting 8. Troubleshooting www.gastron.com Instruction Manual 32_33 8.1. Fault List 8.2. Recovery List FAULT MESSAGE DESCRIPTION & CONDITION CAUSE FOR OCCURRENCE CAUSE FOR OCCURRENCE COPING MEASURE MPU inside transmitter defective Replace Transmitter Main Board FAULT0 When Memory(FLASH, RAM) Check Sum error occurs Transmitter inside MPU defective "> TSM-MEM C/S"... -
Page 18: Interface Configuration
Toggle Bit(Bit inversion at an interval of 2 Sec) Outside Test BIT0~7 Setting for Gas detector Test Mode Outside Reset BIT0~7 Setting for Gas detector Test Mode [Table 15.Configuration of RS485 MODBUS Address] [Figure 19. Outline drawing for GIR-3000W Standard Type]... -
Page 19: Warning Light Gtl-100
10. Outline drawing and Dimensions 10. Outline drawing and Dimensions www.gastron.com Instruction Manual 36_37 10.2. Warning light GTL-100 10.3. Upon coupling of warning light [Figure 20. Outline drawing for GTL-100] [Figure 21. Outline drawing for coupling of GIR-3000W warning light]... -
Page 20: Gir-3000W Remote Type
■ Alarm of the gas leakage detection alarm should be installed at a place with the Gas detector installed and places for permanent residence of workers. [Figure 22. GIR-3000W remote Type]... -
Page 21: Notes Upon Installation
GIR-3000W 11. Notes before installation 12. Revision record www.gastron.com Instruction Manual 40_41 11.3. Notes upon installation Version Contents Date * Initial revision of manual 2017.09.26 Positions with rainwater, etc. that can be an electrical obstacle should be avoided for installation, and installation at a place facilitating operation is recommended since periodic maintenance and repair is required.
Need help?
Do you have a question about the GIR-3000W and is the answer not in the manual?
Questions and answers