Lightware FP-HDMI-TPS-RX97-GB3 Quick Start Manual

Quick Start Guide
FP-HDMI-TPS-RX97-GB3
WP-HDMI-TPS-RX97
Important Safety Instructions
Please read the supplied safety instruction document before using the product and keep it
available for future reference.
Introduction
WP/FP-HDMI-TPS-RX97 series twisted pair HDBaseT extenders provide extension of
TM
uncompressed 4K/UHD video with embedded audio (up to eight channel PCM or HBR audio)
for long distances over a single CATx cable.
Box Contents
HDMI OUT
Receiver unit Safety and Warranty info, Phoenix
Quick Start Guide 3-pole connector
* For WP-HDMI-TPS FP-8AT front plate only.
UNC 6-32 bright zinc plated
 Please note that the 48V power adaptor is
pan head screws (4x) *
an optional accessory which can be purchased
separately.
Power Supply Options
TPS-97 extenders are compatible with IEEE 802.3af standard - Power over Ethernet (PoE) -
and can receive power over the TPS line.
The extender can be powered by any of the following ways:
1. Local adaptor 2. Remote power injector 3. Matrix board
Power
send
SIGN
AL
LIVE LINK
CATx
TPS-PI-1P1
(TPS)
External
power supply
48V DC
Power send
Power
SIGN
adaptor AL
LIVE
LINK
48V DC
Power
adaptor
 TPS-TX/RX90 and TPS-TX/RX95 are not PoE-compatible, thus not able to remote power
the WP/FP-HDMI-TPS-RX97 series and vica versa. WP/FP-UMX-TPS-RX97 series contains
PoE-compatible remote power function (PD, Powered Device), RX95 and TX95 extenders can
be remote powered only by each other.
¢ Warranty void if damage occurs due to the usage of a different power source.
Front View (WP-HDMI-TPS-RX97 assembled with FP-8AT plate)
1 2 3
Rear View (WP-HDMI-TPS-RX97 assembled with FP-8AT plate)
4
® Combicon
6 7
Bottom View (WP-HDMI-TPS-RX97 assembled with FP-8AT plate)
CATx
(TPS)
SIGN
AL
LIVE
LINK
1
Status LEDs
1
SIGNAL
LINK
LIVE
2
IR input/output
3
RS-232 connector
4
Ethernet
5
HDMI output
5
6
DC Input
7
TPS input
8
RS-232 switch
9
TPS mode switch
q
Tie-down point
8 9 6 q
Compatible Devices
TPS-97 extenders are compatible with all Lightware devices with TPS port except the TPS-90
series.
The product is compatible with any HDBaseT
third party devices.
HDBaseT TM and the HDBaseT Alliance logo are trademarks of the HDBaseT Alliance.
RS-232 Switch Modes
RS-232
Connecting Steps
The LEDs give feedback about the state of the unit and the video
signals.
off No video signal transmission.
on (green) Video signal transmission is active.
off TPS connection failed between the
extenders.
blinking TPS connection is detected and Low
(green) Power Partial Functionality (LPPF) link
mode is active.
on (green) TPS connection is detected and
HDBaseT TM (HDBT) or Long reach (LR)
Compatible
link mode is active.
transmitter or
matrix output
off Device is not powered.
blinking Device is powered and ready to use.
(green)
2 TRS (3.5mm jack) connectors for Infrared units (IR IN for the
detector, IR OUT for the emitter).
3-pole Phoenix connector for RS-232 serial port. Firmware
upgrade can also be performed over this interface.
Locking RJ45 connector for Ethernet communication.
DVI
HDMI output for DVI or HDMI signal. Connect an HDMI cable
CATx
between the receiver and the display device.
Connect the output to the 2-pole Phoenix connector on the
bottom of the wall plate.
Locking RJ45 connector for HDBaseT signal transmission.
TM
HDMI
Connect a twisted pair cable between the transmitter and the
receiver.
RS-232
Normal: serial data is passed through the device.
Prog: RS-232 pass-through function is disabled, the device
IR
is ready for the firmware upgrade (see RS-232 switch modes
section for details).
LR: Longreach TPS mode; lower resolution (max 1080p),
LAN
longer distances.
Auto: TPS mode is determined automatically.
Power
The built-in tie-down points are designed to clamp the
HDMI and the CATx cable and ensure stable connection.
Please see the enlarged picture below.
The product brief and further information of this appliance is available at www.lightware.com.
TM
Switch
normal
TPS port
prog
Programming
Projector
HDMI RS-232
WP-HDMI-TPS-RX97-US
CATx CATx
Ethernet HDMI OUT
TPS-PI-1P1
Power injector
WP-HDMI-TPS-RX97
board
Power IR
Power adaptor IR detector Ethernet
Connect the TPS input port of the receiver to the TPS+PoE port of the
TPS-PI-1P1 by a CATx cable.
Connect the receiver (or the matrix output board) to the power injector by a
CATx cable via the TPS port.
Connect the sink (e.g. Projector) to the HDMI output port by HDMI cable.
Optionally for RS-232 extension: connect a controller/controlled device (e.g.
Projector) to the RS-232 port.
Optionally for Infrared extension:
ƒ Connect the IR emitter to the IR OUT port of the receiver, and/or
ƒ Connect the IR detector to the IR IN port of the receiver.
Optionally connect the receiver to a LAN.
Powering on the devices is recommended to do as the final step during the
installation. Please check the Power Supply Options section for the details.
Further Information
See the Downloads section on the on the dedicated product page.
Contact us
sales@lightware.com
+36 1 255 3800
support@lightware.com
+36 1 255 3810
Lightware Visual Engineering LLC.
Peterdy 15, Budapest H-1071, Hungary
Doc. ver.: 2.0
19200172
LAN