Ecco Pro Vantage 12+ Series Installation And Operation Instructions Manual

Lightbars
Hide thumbs Also See for Pro Vantage 12+ Series:

Advertisement

IMPORTANT!
Read all instructions before installing and using. Installer: This manual must be
delivered to the end user. This manual assumes installation by a suitably qualified Automotive Technician.
Do not install and/or operate this safety product unless you have read and understand the safety
information contained in this manual.
1. Proper installation combined with operator training in the use, care and maintenance of emergency warning devices are essential to
ensure the safety of emergency personnel and the public.
2. Emergency warning devices often require high electrical voltages and/or currents. Exercise caution when working with live electrical
connections.
3. This product must be properly grounded. Inadequate grounding and/or shorting of electrical connections can cause high current
arcing, which can cause personal injury and/or severe vehicle damage, including fire.
4. Proper placement and installation is vital to the performance of this warning device. Install this product so that output performance of
the system is maximized and the controls are placed within convenient reach of the operator so that s/he can operate the system
without losing eye contact with the roadway.
5. It is the responsibility of the vehicle operator to ensure daily that all features of this product work correctly. In use, the vehicle operator
should ensure the projection of the warning signal is not blocked by vehicle components (i.e., open trunks or compartment doors),
people, vehicles or other obstructions.
6. The use of this or any other warning device does not ensure all drivers can or will observe or react to an emergency warning signal.
Never take the right-of-way for granted. It is your responsibility to be sure you can proceed safely before entering an intersection, drive
against traffic, respond at a high rate of speed, or walk on or around traffic lanes.
7. This equipment is intended for use by authorized personnel only. The user is responsible for understanding and obeying all laws
regarding emergency warning devices. Therefore, the user should check all applicable city, state, and federal laws and regulations.
The manufacturer assumes no liability for any loss resulting from the use of this warning device.
8. This product may contain high intensity LEDs staring directly into these lights could result in temporary and/or permanent vision
impairment.
!
WARNING!
Failure to install or use this product according to manufacturer's recommendations may result in property
damage, serious bodily/personal injury, and/or death to you and those you are seeking to protect!
Unpacking and Pre-Installation:
Carefully remove the lightbar and place it on a flat surface. Examine the unit for transit damage and locate all parts. If damage is found or
parts are missing, contact the transit company or ECCO. Do not use damaged or broken parts. Ensure the lightbar voltage is compatible with
the planned installation.
Specifications:
Length.................24", 30", 36", 42", 48", 54", 60", 72"
Width...................11"
Height..................2.5"
Voltage................12-24VDC
Current Draw.......Single Color LED Module = 0.55A Avg. @ 12.8VDC
Dual Color LED Module = 0.55A Avg. @ 12.8VDC
LED STT (pair) = 1.2A Avg.@ 12.8VDC
LED AL,TD,WL = 1.2A Avg. @ 12.8VDC
Flash Patterns.....70
Installation & Mounting:
Mounting
Before proceeding with installation, plan all wiring and cable routing. Select the mounting location for the lightbar on a flat, smooth surface
and center the unit across the width of the vehicle. The mounting location for the lightbar should be chosen such that the lightbar is level
and visibility to approaching traffic is optimized. Mounting should be such that there is no less than ½" clearance between the roof and the
lightbar at any point.
Installation and Operation Instructions
12+ Pro Vantage™ Series Lightbars
Fuse Recommendation:
Calculate the total amp draw from all the LED Modules.
Multiply the total amp draw by 1.25. Round up to the
nearest fuse.
Page 1 of 14

Advertisement

Table of Contents
loading

Summary of Contents for Ecco Pro Vantage 12+ Series

  • Page 1 Carefully remove the lightbar and place it on a flat surface. Examine the unit for transit damage and locate all parts. If damage is found or parts are missing, contact the transit company or ECCO. Do not use damaged or broken parts. Ensure the lightbar voltage is compatible with the planned installation.
  • Page 2: Permanent Mounting

    Caution: When drilling into any vehicle surface, make sure that the area is free from any electrical wires, fuel lines, vehicle upholstery, vehicle support members, etc. that could be damaged. Permanent Mounting 1. Determine the location of the lightbar, and the best route for the wiring. Install on the structural part of the roof or surface that has the least amount of flex.
  • Page 3 Gutter Mounting Important! Mounting brackets are specific to the vehicle model. Please make sure the brackets are suitable for the vehicle before installation. Install on the structural part of the roof that has the least amount of flex. 1. Remove mounting foot. Position bracket onto nubs of the foot. 2.
  • Page 4: Wiring Instructions

    Wiring Instructions: Important! This unit is a safety device and it must be connected to its own separate, fused power point to assure its continued operation should any other electrical accessory fail. Do not wire in parallel with any other accessory. Notes: 1.
  • Page 5 COMBINED POWER/SIGNAL CABLE Combined 12+ Pro Vantage™ Lightbar power/signal cable Combined power/signal cable BLACK (GROUND) STTs OPTIONAL BROWN (PATTERN 1) Optional Stop/Tail/Turn *Brown + Orange = Pattern 3 (STT) Cable ORANGE (PATTERN 2) YELLOW (ALLEY LEFT) GREEN (ALLEY RIGHT) BROWN (TAIL) GREY (ARROWSTICK LEFT) NOTE: GREEN AND YELLOW YELLOW (LEFT TURN)
  • Page 6: Maintenance

    SERIAL INTERFACE BOX (EZMATSIB) GRAY/BLK - Ignition Wire Yellow - Left Alley 12+ Pro Vantage™ Lightbar 4-Pin Connector Purple - Right Alley Gray - WL/Alley Flash ORG/BLK - Takedown Pink - LR Arrowstik STTs OPTIONAL Power/Ground Cable Orange - RR Arrowstick Optional Stop/Tail/Turn YLW/BLK - Arrowstik Flash (STT) Cable...
  • Page 7 Alley / Takedown / Worklight LED Modules (EZ0003) Alley / Takedown / Worklight LED Module can be mounted anywhere in the lightbar. Stop / Tail / Turn LED Modules (EZ1205) Stop Tail Turn modules operate in conjunction with the vehicle tail, brake and direction indicator lights.
  • Page 8 Advanced Controller (EZ1202) Provides convenient control of the lightbar’s built-in flash patterns and features soft touch buttons and LED function indicator lights. 12+ PRO ADVANCED CONTROLLER FUNCTIONS ECCOESG.com P/N EZ1202 Toggle Press / Press for 2 Seconds Flash Pattern 1 Select Take Down Cruise...
  • Page 9: Special Features

    “Safety Director On/Off” - Press once to turn the Safety Director on or off. “Safety Director Pattern Select” - Once the Saftey Director is activated, press this pattern select button to cycle to the next Safety Director flash pattern. There is a 5 second delay between the controller and the lightbar.
  • Page 10 Advanced Control Pad Mounting: BRACKET The advanced control pad is supplied with three mounting op- tions: a bracket, VHB tape and hook and loop patch. The rear of the control pad is designed to allow for the cable exit to be routed five different ways to maximize installation locations.
  • Page 11 STANDARD FLASH PATTERNS: NOTE: 1. All SAE J845 compliant patterns have at least 180° of coverage with the minimum configuration of two corner modules, one forward facing and one rear facing module. Page 11 of 14...
  • Page 12: Replacement Parts/Accessories

    Permanent mounting feet and hardware - Black ER0002 Permanent mounting feet and hardware - White ER0001 Headache rack mounting kit A1032RMK NOTE: For list of vehicle specific brackets, please contact an ECCO representative or our latest catelog. Page 12 of 14...
  • Page 13: Troubleshooting

    Troubleshooting: All lightbars are thoroughly tested prior to shipment. However, should you encounter a problem during installation or during the life of the product, follow the guide below for troubleshooting and repair information. If the problem cannot be rectified using the solutions given below, additional information may be obtained from the manufacturer –...
  • Page 14 Electronics Controls Company “ECCO” (Manufacturer) ECCO warrants that on the date of purchase, this product will conform to ECCO’s specifications for this product (which are available from ECCO upon request). This Limited Warranty extends for sixty (60) months from the date of purchase.

Table of Contents