Advertisement
Quick Links
CONVENTIONAL AIR CAP AND FLUID NOZZLE CHART
MODEL
PRESS /
AIR CAP
NO.
SIPHON
21-2166
21-2266
Siphon
21-2266T
21-2366
TG
21-2466
21-2163
21-2263
Pressure
21-2266-3
21-2266-3T
Actual fluid nozzle and air cap combinations are determined by application (see application chart page 4)
*Gun inlet pressures may vary as required by application
Coating Atomization Technologies 337 South Arthur Avenue, Louisville CO 80027 Phone: 888.820.4498, Fax: 303.438.5708
FLUID TIP
FAN
RANGE
CONTROL
0.6 - 1.8
0.6 - 1.8
0.6 - 1.8
0.6 - 1.8
60-1317
0.6 - 1.8
0.6 - 1.8
0.6 - 1.8
0.6 - 1.8
0.6 - 1.8
www.spraycat.com
T T T T T omaha
PRESSURE/SIPHON FEED SPRAY GUN
AIR CAP
AVAILABLE FLUID
SCFM
RING
5
12
31-0606 0.6mm (.022")
12
31-0607 0.7mm (.028")
12
31-0610 1.0mm (.040")
Included
15
31-0612 1.2mm (.046")
8
31-0613 1.3mm (.052")
14
31-0615 1.5mm (.059")
16.2
31-0618 1.8mm (.070")
16.2
omaha
omaha wk
omaha
omaha
PRODUCT INFORMATION
NOZZLES
marking on needle
40-2807 (2807)
40-2810 (2810)
40-2815 (2815)
wk
wk
wk
wk
NEEDLES /
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for C.A. Technologies Tomahawk TG
Summary of Contents for C.A. Technologies Tomahawk TG
- Page 1 T T T T T omaha omaha omaha wk omaha omaha PRESSURE/SIPHON FEED SPRAY GUN PRODUCT INFORMATION CONVENTIONAL AIR CAP AND FLUID NOZZLE CHART MODEL PRESS / FLUID TIP AIR CAP AVAILABLE FLUID NEEDLES / AIR CAP SCFM SIPHON RANGE CONTROL RING NOZZLES...
- Page 2 T T T T T omaha omaha omaha omahawk omaha Operation and Maintenance Instructions for Spray Guns Operation 1. Connect air supply hose at handle of gun. 2. Connect a pressurized fluid supply to the gun fluid inlet. 3. Fluid flow can be controlled using the fluid control knob, this restricts flow by limiting needle travel. It is best to control fluid flow by proper selection of fluid orifice size and use the fluid control knob to “fine tune flow rate”.
- Page 3 ITEM NO. PART NO. DESCRIPTION ITEM NO. PART NO. DESCRIPTION See Air Cap Chart Air Cap** See Air Cap Chart Fluid Needle** See Air Cap Chart Fluid Nozzle Tip** 60-211 Needle Return Spring* 60-15C Head Insert 60-104 Air Inlet Fitting 60-137 O-Ring* 60-1319...
- Page 4 FLUID NOZZLE / AIR CAP SELECTION CHARTS TOMAHAWK Series - Pressure / Siphon Feed Guns TG CONVENTIONAL SPRAY GUN FLUID ORIFICE x MAXIMUM MATERIAL TYPE PRESS. / SIPHON AIR CAP PATTERN WIDTH Very Thin 0.6, 0.7 mm x 2163 less than 16 sec. Zahn #2 0.6, 0.7 mm x 2166 inks , dyes, 0.6, 0.7 mm x 2266...
Need help?
Do you have a question about the Tomahawk TG and is the answer not in the manual?
Questions and answers