Advertisement
Quick Links
HVLP AIR CAP AND FLUID NOZZLE CHART
MODEL
AIR CAPS
NO.
22-1028
22-1033
22-1057
22-1100
L200H
22-1100 X 2.2S
22-1046**
22-1083**
*Note: Air cap test gages are available to confirm HVLP compliance.
**Must be used with 32-02XX fluid nozzle tips
Coating Atomization Technologies 337 South Arthur Avenue, Louisville CO 80027 Phone: 888.820.4498, Fax: 303.438.5708
*MAX GUN
Press /
INLET PRESS.
Siphon
CONTROL
FOR HVLP
pressure
29
60-1502 (#2)
pressure
38
60-1502 (#2)
pressure
50
60-1502 (#2)
pressure
37
60-1501 (#1)
siphon
37
60-1502 (#2)
pressure
47
60-1502 (#2)
pressure
55
60-1502 (#2)
SCFM @
FAN
AIR CAP
MAX GUN
RING
INLET
18
18.75
22
18
22-1001
18
22.5
26
www.spraycat.com
L L L L L ynx 200H
ynx 200H
ynx 200H
ynx 200H
ynx 200H
PRESSURE FEED SPRAY GUN
PRODUCT INFORMATION
AVAILABLE FLUID
NOZZLES TIPS
32-0611 1.1mm (.042")
32-0614 1.4mm (.055")
32-0618 1.8mm (.070")
32-0622 2.2mm (.086")
32-0211 1.1mm (.042")
32-0214 1.4mm (.055")
32-0218 1.8mm (.070")
32-0222 2.2mm (.086")
NEEDLES /
marking on needle
40-1211 (211)
40-1214 (214)
40-1218 (218)
40-1222 (222)
40-1211 (211)
40-1214 (214)
40-1218 (218)
40-1222 (222)
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for C.A. Technologies Lynx 200H
Summary of Contents for C.A. Technologies Lynx 200H
- Page 1 L L L L L ynx 200H ynx 200H ynx 200H ynx 200H ynx 200H PRESSURE FEED SPRAY GUN PRODUCT INFORMATION HVLP AIR CAP AND FLUID NOZZLE CHART *MAX GUN SCFM @ MODEL Press / AIR CAP AVAILABLE FLUID NEEDLES / AIR CAPS INLET PRESS.
- Page 2 L200H L200H L200H L200H L200H Operation and Maintenance Instructions for Spray Guns Operation 1. Connect air supply hose at handle of gun. 2. Connect a pressurized fluid supply to the gun fluid inlet. 3. Fluid flow can be controlled using the fluid control knob, this restricts flow by limiting needle travel. It is best to control fluid flow by proper selection of fluid orifice size and use the fluid control knob to “fine tune flow rate”.
- Page 3 HVLP AIR CAP TEST GAGES 22-1028-G 22-1033-G 22-1046-G L200H 22-1057-G GUNS 22-1083-G 22-1100-G ITEM NO. PART NO. DESCRIPTION ITEM NO. PART NO. DESCRIPTION See Air Cap Chart Air Cap** 60-204 Needle Return Spring* See Air Cap Chart Fluid Nozzle Tip** 60-201 Rear Bushing 32-1201...
- Page 4 FLUID NOZZLE / AIR CAP SELECTION CHARTS LYNX Series 200H - Pressure Feed Guns L200H HVLP SPRAY GUN FLUID ORIFICE x MAXIMUM MATERIAL TYPE PRESS. / SIPHON AIR CAP PATTERN WIDTH Very Thin 1.1 mm x 1028 less than 16 sec. Zahn #2 1.1 mm x 1033 inks , dyes, solvents, stains...
Need help?
Do you have a question about the Lynx 200H and is the answer not in the manual?
Questions and answers