Table of Contents
Advertisement
Quick Links
4200 is a new part
number replacing the
3765-2
Suggested Keypads
3715 LGBASIC II
3000 Round Entry
FEATURES
MANAGER CODE (Factory set to 1-2-3-4-5-6)
• Add/Remove User
• Enable/Disable User
USER CODE
• Open Lock
• Change Code
• Four (4) consecutive invalid codes initiates five minute delay
period.
LOW BATTERY WARNING
• Repeated audio and visual signal (LED flashing and repeated
beeping) during opening indicates battery low.
AUDIO AND VISUAL SIGNAL
• Double signal (LED flashes and unit beeps) indicates entry is
valid or accepted.
• Triple signal indicates invalid or not accepted.
OPENING THE LOCK
1 Enter valid six (6) digit code.
2 The lock will signal a valid code entry with a double signal.
3 Within four (4) seconds, turn handle to the open position.
4 Pull door open.
• Invalid Code Entry - Lock will signal three (3) times.
• Security Considerations - On safes using more than one
lock the swingbolt must lock first.
12-219v2
© copyright 2005
3765-2 / 4200 Dual-Handed Swingbolt Lock Instructions
MANAGER PROGRAMMING
3900 LGACCESS
Handle
Input
(Manager)
9-29-05
CHANGING YOUR CODE
ALWAYS PERFORM THIS OPERATION WITH THE DOOR OPEN
1 Enter "zero" six times.
2 Enter your existing six (6) digit code one time.
3 Enter your NEW six (6) digit code two times.
4 If a mistake is made wait thirty (30) seconds and repeat
steps 1 - 3.
5 Test lock operation several times before closing the door.
• Valid Code Entry - Double signal after valid six (6) digit
code is entered.
• Invalid Code Entry - Triple signal and old code is still valid.
ADD USER
ALWAYS PERFORM THIS OPERATION WITH THE DOOR OPEN
1 Enter Manager code and HOLD DOWN LAST DIGIT of
CODE until the lock signals with two sets of double beeps.
2 PRESS 1. Lock signals twice.
3 Enter user code twice. The lock signals twice after each
valid entry.
4 If a mistake is made wait thirty (30) seconds and repeat
steps 1 - 3.
• Valid Code Entry - Double signal after valid six (6) digit
code is entered.
• Invalid Code Entry - Triple signal and old code is still valid.
DISABLE USER
ALWAYS PERFORM THIS OPERATION WITH THE DOOR OPEN
1 Enter Manager code and HOLD DOWN LAST DIGIT of
CODE until the lock signals with two sets of double beeps.
2 PRESS 2. Lock signals once.
3 User is temporarily disabled.
4 If a mistake is made wait thirty (30) seconds and repeat
steps 1 - 3.
• Valid Code Entry - Double signal after valid six (6) digit
code is entered.
• Invalid Code Entry - Triple signal and old code is still valid.
REINSTATE USER
ALWAYS PERFORM THIS OPERATION WITH THE DOOR
OPEN
1 Enter Manager code and HOLD DOWN LAST DIGIT of
CODE until the lock signals with two sets of double beeps.
2 PRESS 1. Lock signals once.
3 User is reinstated.
4 If a mistake is made wait thirty (30) seconds and repeat
steps 1 - 3.
• Valid Code Entry - Double signal after valid six (6) digit
code is entered.
• Invalid Code Entry - Triple signal and old code is still valid.
LA GARD INC
Advertisement
Table of Contents
Related Manuals for La Gard LGBASIC 3765-2
Summary of Contents for La Gard LGBASIC 3765-2
- Page 1 4 Pull door open. • Invalid Code Entry - Lock will signal three (3) times. • Security Considerations - On safes using more than one lock the swingbolt must lock first. LA GARD INC 12-219v2 © copyright 2005 (Manager) 9-29-05...
- Page 2 • Repeated beeping during an opening indicates that the battery is low and needs immediate replacement. • Uses one (1) 9-Volt Alkaline Battery. LA GARD recommends the use of Duracell™ or Eveready™ Alkaline batteries. LA GARD recommends the replacement of batteries at least once annually.
Need help?
Do you have a question about the LGBASIC 3765-2 and is the answer not in the manual?
Questions and answers
I cannot get into my safe. I have a Lagard Lg model # 3765004A-00. I do not know the combination. How can I unlock and reset a code?
The provided context does not include instructions for unlocking or resetting the code if the combination is unknown. Typically, if the combination is lost, you may need to contact the manufacturer or a professional locksmith for assistance.
This answer is automatically generated
Inside of door - one bar will not retract so we can’t shut the door
I am trying to reset my code. I have followed the instructions several times and it keeps reverting back to the code we are trying to delete. Opened the safe Entered six 0’s Entered the old code one time Entered the new code two times. Got a double beep upon entering the new code the second time. It makes no sense.