LG LREL6325 Series Owner's Manual page 17

3 - W i r e C o n n e c t i o n : C o n d u i t
In s t a l l t h e c o n d u i t a s f o l l o w s :
Remove the conduit connection plate from the rear of
the oven and rotate it. The conduit hole (1
be used.
First, prepare the conduit wires as shown below.
3 - W i r e
Conduit
or
connection
plate
Second, install the conduit strain relief.
For conduit installations, purchase a strain relief and
insert it in the 1 1 / in. (2.8 cm) conduit hole. Then
8
install the conduit through the body of the strain relief
and fasten the strain relief with its ring. Reinstall the
bracket.
For conduit connections:
If the wire in the conduit is copper it must be 8 or 10
AWG wiring.
If the wire in the conduit is aluminum it must be 6 or 8
AWG wiring.
1
Loosen the lower 3 screws from the terminal
block.
2
Insert the bare wire (white/neutral) end through
the center terminal block opening.
D o n o t r e m o v e t h e g r o u n d s t r a p c o n n e c t i o n s .
3
Insert the two side bare wire ends into the lower
left and the lower right terminal block openings.
Tighten the 3 screws securely into the terminal
block. (approximately 35 - 50 IN-LB)
3 - w i r e c o n n e c t i o n
Black White Red
Conduit
connection plate
If screws are not tightened securely, it can result in
electrical spark and severe personal injury or death.
4 - W i r e C o n n e c t i o n : C o n d u i t
1 / ") must
8
4 - W i r e
Ground
wire
4 - w i r e c o n n e c t i o n
Terminal
block
Wire
ends
If screws are not tightened securely, it can result in
electrical spark and severe personal injury or death.
W A R NING
• T h e w h i t e m i d d l e ( n e u t r a l ) w i r e o f t h e p o w e r
c o r d o r 4 - w i r e c o n d u i t h a s t o b e c o n n e c t e d
t o t h e m i d d l e p o s t o f t h e m a i n t e r m i n a l
b l o c k . T h e o t h e r t w o w i r e s o f t h e p o w e r
c o r d o r c o n d u i t h a v e t o b e c o n n e c t e d t o
t h e o u t s i d e p o s t s o f t h e m a i n t e r m i n a l
c o n n e c t i o n b l o c k . T h e 4 t h g r o u n d w i r e
( g r e e n ) m u s t b e c o n n e c t e d t o t h e f r a m e o f
t h e r a n g e w i t h t h e g r o u n d s c r e w . Failure
to do so can result in electrical shock, severe
personal injury or death.
1
Follow the instructions for installing the conduit
under 3-Wire Connection: Conduit until the strain
relief and bracket are installed. Do not install the
conduit without a strain relief.
2
Loosen the 2 lower left and right screws from
the terminal block. Remove the lower 2 center
screws. Do not discard any screws.
3
Remove the ground screw and bend the end of
the ground strap up so the slot is over the hole
of the center screw removed in step 1.
4
Attach the ground (green) bare wire end to
the range frame and secure it in place with the
ground screw.
5
Insert the bare wire (white/neutral) end through the
center terminal block opening. The center screw
now attaches the bent up ground strap to the block.
6
Insert the two side bare wire ends into the left
and the right terminal block openings. Tighten
the 3 screws securely into the terminal block.
(approximately 35 - 50 IN-LB)
Black White Red
Wire
ends
Conduit
connection
plate
Ground
screw
INSTALLATION 1 7
Terminal
block
Ground
strap
Bend strap
up and
attach
Ground
wire