LG LREL6325 Series Owner's Manual page 12

1 2 INSTALLATION
In s t a l l i n g t h e R a n g e
U n p a c k i n g a n d M o v i n g t h e R a n g e
C A U T IO N
• Y o u s h o u l d u s e t w o o r m o r e p e o p l e t o m o v e
a n d i n s t a l l t h e r a n g e . ( Ex c e s s i v e W e i g h t
Ha z a r d ) Failure to do so can result in back or
other injury.
• D o n o t u s e t h e d o o r h a n d l e s t o p u s h o r
p u l l t h e r a n g e d u r i n g i n s t a l l a t i o n o r w h e n
m o v i n g t h e r a n g e o u t f o r c l e a n i n g o r
s e r v i c e . Doing so can result in serious damage
to the door of the range.
Remove packing material, protective film, tape and
any temporary labels from your range before using.
Do not remove any warning-type labels, the model
and serial number label, or the Tech Sheet that is
located on the back of the range.
To remove any remaining tape or glue, rub the area
briskly with your thumb. Tape or glue residue can also
be easily removed by rubbing a small amount of liquid
dish soap over the adhesive with your fingers. Wipe
with warm water and dry.
Do not use sharp instruments, rubbing alcohol,
flammable fluids, or abrasive cleaners to remove tape
or glue. These products can damage the surface of
your range.
Your range is heavy and can be installed on soft
floor coverings such as cushioned vinyl or carpeting.
Use care when moving the range on this type of
flooring. Use a belt when moving the range to prevent
damaging the floor. Or slide the range onto cardboard
or plywood to avoid damaging the floor covering.
C h o o s i n g t h e P r o p e r Lo c a t i o n
C A U T IO N
• A v o i d p l a c i n g c a b i n e t s a b o v e t h e r a n g e . To
minimize the hazard caused by reaching over
the open flames of operating burners, install a
ventilation hood over the range that projects
forward at least five inches beyond the front of
the cabinets.
• M a k e s u r e w a l l c o v e r i n g , c o u n t e r t o p a n d
c a b i n e t s a r o u n d t h e r a n g e c a n w i t h s t a n d
t h e h e a t ( u p t o 1 9 4 ° F ) g e n e r a t e d b y t h e
r a n g e . Discoloration, delamination or melting
may occur. This range has been designed to
comply with the maximum allowable wood
cabinet temperature of 194 °F.
• B e f o r e i n s t a l l i n g t h e r a n g e i n a n a r e a
c o v e r e d w i t h l i n o l e u m
f l o o r c o v e r i n g , m a k e s u r e t h e f l o o r c o v e r i n g
c a n w i t h s t a n d t e m p e r a t u r e s o f a t l e a s t
2 0 0 ° F ( 9 3 ° C ) .
• U s e a n i n s u l a t e d p a d o r
p l y w o o d u n d e r t h e r a n g e i f i n s t a l l i n g t h e
r a n g e o v e r c a r p e t i n g .
The range should always be plugged into its own
individual properly grounded electrical outlet. This
prevents overloading house wiring circuits which
could cause a fire hazard from overheated wires. It is
recommended that a separate circuit serving only this
appliance be provided.
M o b i l e Ho m e - A d d i t i o n a l In s t a l l a t i o n
R e q u i r e m e n t s
The installation of this range must conform to the
Manufactured Home Construction and Safety
Standard, Title 24 CFR, Part 3280 (formerly the
Federal Standard for Mobile Home Construction
and Safety, Title 24, HUD Part 280), or when
such standard is not applicable, the Standard for
Manufactured Home Installations, ANSI A225.1/NFPA
501A or with local codes.
• When this range is installed in a mobile home, it
must be secured to the floor during transit. Any
method of securing the range is adequate as long
as it conforms to the standards listed above.
• A four-wire power supply cord or cable must be
used in a mobile home installation.
o r o t h e r s y n t h e t i c
/ i n . ( 0 . 6 4 c m )
1
4