LG LREL6325 Series Owner's Manual page 15

W A R NING
• A l l o w
2 t o 3 f t ( 6 1 . 0 c m
i n t h e l i n e s o t h a t t h e r a n g e c a n b e m o v e d i f
s e r v i c i n g i s e v e r n e c e s s a r y .
• T h e p o w e r s u p p l y c o r d a n d p l u g s h o u l d
n o t b e m o d i f i e d . If i t w i l l n o t f i t t h e o u t l e t ,
h a v e a p r o p e r o u t l e t In s t a l l e d b y a q u a l i f i e d
e l e c t r i c i a n .
• U s i n g a n e x t e n s i o n c o r d t o c o n n e c t t h e
p o w e r i s p r o h i b i t e d . C o n n e c t t h e p o w e r
c o r d a n d p l u g d i r e c t l y .
• El e c t r i c a l g r o u n d i s r e q u i r e d o n t h i s
a p p l i a n c e .
• M a k e s u r e t h a t t h e p o w e r c o r d i s n o t
p i n c h e d b y t h e r a n g e o r h e a v y o b j e c t s .
Failure to do so can result in serious burns or
electrical shock.
Sp e c i f i e d p o w e r - s u p p l y - c o r d k i t r a t i n g
Specified
Range rating, watts
rating of
supply-
120/240 120/208
cord kit,
volts volts
amperes
3-wire 3-wire
8,750 - 7,801 - 40 or 50A
16,500 12,500
16,501 - 12,501 -
22,500 18,500
3, 4 - Wire electrical wall Receptacle
4 W i r e r e c e p t a c l e ( 1 4 - 5 0 R )
3 W i r e r e c e p t a c l e ( 1 0 - 5 0 R )
C o n n e c t i n g t h e P o w e r C o r d
The rear access cover must be removed. Loosen the
two screws with a screwdriver. The terminal block will
then be accessible.
Access cover
t o 9 1 . 4 c m ) o f s l a c k
Diameter (inches)
of Range
connection
power
Opening
Power
Conduit
cord
1 3 / " 1 1 /
8 8
50 1 3 / " 1 3 /
4 8
Use the cord/conduit connection plate to install the
power cord or conduit. Leave the connection plate
as installed for power cord installations. Remove the
connection plate for conduit installations and use the
smaller 1 1 / in. (2.8 cm) conduit hole instead of the
8
1 3 / in. (3.5 cm) power cord hole.
8
1
1 / " (2.8 cm) Conduit
8
1 3 / " (3.5 cm) Cord
8
Remove the Conduit connection plate
For power cord installations, hook the strain relief
over the 1 3 / in. (3.5 cm) power cord hole located
8
below the rear of the oven. Insert the power cord
through the strain relief and tighten it.
"
Assembling power cord strain relief at the 1
"
For conduit installations, insert the conduit strain
relief in the 1 1 / in. (2.8 cm) conduit hole. Then install
8
the conduit through the body of the strain relief and
fasten the strain relief with its ring.
Ring
Body
Assembling conduit cord strain relief at the 1
INSTALLATION 1 5
Conduit
connection
plate
Power cord
3 / " opening
8
Cord/
Conduit
connection
plate
Conduit
1 / " opening
8