Maintenance And Care - Flex CSM 4060 Manual

Portable circular saw for metals CSM 4060
Tighten the clamping lever (10).
Operation
`~ìíáçå>
^ÑíÉê=íÜÉ=éçïÉê=íççä=Ü~ë=ÄÉÉå=ëïáíÅÜÉÇ=çÑÑI=
íÜÉ=ë~ï=Ää~ÇÉ=ÅçåíáåìÉë=êìååáåÖ=ÄêáÉÑäóK
tÜÉå=íÜÉ=êìååáåÖ=ë~ï=Ää~ÇÉ=íçìÅÜÉë=íÜÉ=
ïçêâéáÉÅÉI=íÜÉ=éçïÉê=íççä=ã~ó=êÉÅçáäK
Sawing
kçíÉ>
bñÅÉëëáîÉ=ÑÉÉÇ=êÉÇìÅÉë=íÜÉ=éÉêÑçêã~åÅÉ=çÑ íÜÉ=
éçïÉê=íççäI=áãé~áêë=íÜÉ=ÅìííáåÖ=èì~äáíó=~åÇ=
êÉÇìÅÉë=íÜÉ=ëÉêîáÅÉ=äáÑÉ=çÑ=íÜÉ=ë~ï=Ää~ÇÉK=
Take hold of the handle (1) with your right
hand and the additional hand grip (6) with
your left hand.
Switch on the power tool and wait until the
saw blade has reached the maximum
speed.
Slowly bring the power tool towards
the material.
Guide the power tool through the material
at a uniform feed.
Parallel stop
Facilitates cuts parallel to the edge of the
workpiece.
Loosen the wing screw (8).
Set the parallel stop (18) to the required
width.
Tighten the wing screw (8).
Overload protection
If there is an extreme overload, the overload
protection system protects the motor from
damage by automatically switching off the
power tool.
Release the safety switch (4).
Pull out the mains plug.
Leave the appliance to cool down for
at least 3 minutes.
Press the overload protection reset
button (2).
The power tool is ready to use again.

Maintenance and care

a~åÖÉê>
_ÉÑçêÉ=Å~êêóáåÖ=çìí=~åó=ïçêâ=çå=íÜÉ=éçïÉê=
íççäI=~äï~óë=éìää=çìí=íÜÉ=ã~áåë=éäìÖK
Cleaning
a~åÖÉê>
fãé~áêãÉåí=çÑ=íÜÉ=éêçíÉÅíáîÉ=áåëìä~íáçå>
fÑ=ãÉí~äë=~êÉ=ë~ïå=çîÉê=~ éêçäçåÖÉÇ=éÉêáçÇI=
ÅçåÇìÅíáîÉ=Çìëí=ã~ó=ÄÉÅçãÉ=ÇÉéçëáíÉÇ=áåëáÇÉ=
íÜÉ=ÜçìëáåÖK=
léÉê~íÉ=íÜÉ=éçïÉê=íççä=îá~=~ êÉëáÇì~äJÅìêêÉåíJ
çéÉê~íÉÇ=ÅáêÅìáíJÄêÉ~âÉê=EíêáééáåÖ ÅìêêÉåí=
PM ã^FK
Regularly clean the power tool and
ventilation slots.
Regularly blow out the housing interior and
motor with dry compressed air.
23