IMPORTANT SAFETY INSTRUCTIONS Please read the User Guide carefully before recharging or operating your Phoenix 200. IMPORTANT SYMBOLS Indicates potentially dangerous conditions that could result in personal injury WARNING Indicates conditions or practices that could result in damages to the unit or other...
Equipped with multiple output ports to power mainstream essential gadgets and small appliances at the push of a button. EASY RECHARGING Conveniently charge the Phoenix 200 through a wall outlet, a car socket, or with a solar panel. COMPREHENSIVE PROTECTION The battery management system (BMS) enables voltage control, temperature control, short circuit protection, overcurrent protection, and more advanced safety operations.
Battery Level LED Indicators Flashlight On/Off Button Port Status LED Indicators Main Power Button Flashlight Status LED Indicators AC Outlets CIG Port DC Input Port USB-A Ports Folding Carrying Handle USB-C Port LED Flashlight DC Output Port Air Vent Port On/Off Buttons SPECIFICATIONS General Dimension...
Four Battery Level LED Indicators indicate the battery level of the PHOENIX 200, approximating 25% - 50% - 75% - 100% capacity. As you use your PHOENIX 200 to power other devices, the Battery Level LED Indicators will go out one by one to indicate the remaining battery capacity.
Page 9
PHOENIX 200 and place your PHOENIX 200 in the shade to prevent it from overheating. The PHOENIX 200 will begin to recharge automatically and one of the Battery Level LED Indicators will flash. The flashing LED indicates the unit’s current battery level.
Page 10
Adapter to recharge your PHOENIX 200. Recharging via Car Socket Plug your PHOENIX 200 into a car socket through the DC Input Port using the included Cigarette Lighter Plug to 5.5mm DC Adapter Cable. The PHOENIX 200 will begin to recharge automatically and one of the Battery Level LED Indicators will flash.
PHOENIX 200. For some makes or models of vehicles, the car socket may not operate when the ignition is turned off. In such cases, please start the engine before recharging your PHOENIX 200 via the NOTE...
Page 12
Port On/Off Button(s) to turn it (them) off and the corresponding Port Status LED Indicator(s) will go out. When no device is connected to the PHOENIX 200, long press the Main Power Button to turn it off to conserve energy.
MAINTENANCE To prolong the service life of your PHOENIX 200, keep it away from harsh sunlight, water, dust, and dirt. DO NOT leave your PHOENIX 200 outside under harsh environments. If possible, keep your PHOENIX 200 connected to a power source when it is not being used and avoid using large loads when the battery level is low.
TROUBLESHOOTING If your PHOENIX 200 does not operate normally, please refer to the following table for a possible cause and solution. If the following troubleshooting solutions do not work, please contact us for help. Refer to the last page of User Guide for contact information.
Page 15
If output ports can be turned on, it means that the loads drew too much power from the unit and pulled down the battery voltage. In this case, only connect small loads to the unit. If none of the output ports can be turned on, it means that the unit should not continue powering loads.
Page 16
powering those loads via the CIG Port Short-circuit DC Output Port or CIG Port. Protection If the power source was DC Output Port Reverse connected to the DC Output Current Protection Port, disconnect the power source and recharge the unit via the DC Input Port instead.
2. Can I replace the battery pack in my PHOENIX 200? No, the battery pack in PHOENIX 200 is not replaceable. Do not try to dismantle your PHOENIX 200 and replace the battery by yourself. Doing so may cause irreversible damages to the unit and battery explosion.
4. Is the PHOENIX 200 waterproof? No, the PHOENIX 200 is not waterproof. Please keep the unit away from moisture. Do no submerge the unit in water or operate the unit in the rain. Doing so may cause short-circuits, electric shocks, and fire.
Page 35
FCC Compliance: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must withstand any interference received, including interference that may cause undesired operation. MADE IN CHINA...
Page 36
RENOGY.COM Renogy reserves the right to change the contents of this manual without notice. 2775 E Philadelphia St, Ontario, CA 91761, USA 909-287-7111 www.renogy.com support@renogy.com 苏州高新区科技城培源路1号5号楼-4 400-6636-695 https://www.renogy.cn support@renogy.cn https://www.renogy.jp supportjp@renogy.com https://ca.renogy.com supportca@renogy.com https://au.renogy.com supportau@renogy.com https://uk.renogy.com supportuk@renogy.com https://de.renogy.com supportde@renogy.com...
Need help?
Do you have a question about the PHOENIX 200 and is the answer not in the manual?
Questions and answers