Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Yadea V7
Summary of Contents for Yadea V7
- Page 1 USER MANUAL V1.0...
- Page 2 Statement Catalogue At the beginning of printing, this manual contains 1. Foreword..............01 the latest product information at that time.Yadea is 2.Safety precautions..........02 committed to improving product design and quality. 3.Scooter structure............11 As a result, the product design may be changed at 4.Oprate instruction...........15...
- Page 3 For the safety of you and your family and to prevent accidents, please be sure to read and observe the following First of all, thank you for choosing to buy "YADEA" safety precautions and relevant laws and regulations. products. This manual introduced the knowledge and...
- Page 4 Driving safety 3.When riding, we should wear helmet, goggles and other protective devices that meet the safety standards 1.It is strictly prohibited to lend the scooter to anyone who is not familiar with its performance. correctly. We should wear clothes that are clear, free to 2.Electric scooter shall carry personnel or articles in move all over, not tight, and not open cuffs.
- Page 5 5.Before washing water with electric motor, you should know the contents of the instructions on "matters needing attention in washing water". 6.If the power supply is damaged or the charging system fails, replace and maintain it at the authorized repair shop designated by YADEA.
- Page 6 Prevent electrical components from entering water; When cleaning the scooter, avoid water from impacting the or contaminated, etc. If there is any abnormality, please contact YADEA authorized service station for repair or find charging socket, wiring harness connector, fuse and other professional repair.
- Page 7 In case of failure, and charger must not be covered with anything, and the they should go to YADEA professional service station charger must not be placed on the saddle, so as not to affect for maintenance..
- Page 8 3.SCOOTER STRUCTURE Scooter structure diagram 1.Left rear brake lever 2. Left grip 3. Left switch group 1.Front fender 2. Headlight 3. Speedometer 4. Handlebar 5. Battery 4. Speedometer 5. Right switch group 6. Throttle 6. Seat cushion 7. Armrest 8. Taillight 9. Rear fender 10. Rear reflector 7.
- Page 9 VIN Frame coding Speedometer function(If applicable) Example: LR4DE190××××××××× Height 7mm Depth 0.2mm Frame stand tube 8 9 10 Motor model coding 1.Throttle failure indication 2. Left turning light 3. Motor failure indication 4. Battery charging state 5. Under voltage indication 6. Brake indication 7. POWER mode 8.
- Page 10 Power lock switch 4.OPERATE INSTRUCTION Power off Installation of the battery(If applicable) Power on Seat lock/Anti-theft lock Lock hole Battery 1.Power on: Insert the key into the electric door lock switch and rotate clockwise to the right to this position , the power is turned on, and the key cannot be pulled out.
- Page 11 Anti-theft alarm(If applicable) Left switch group High beam/Low beam Lock Turning light Unlock Horn 1.High beam and low beam switch: When the main light switch is turned on, press the high beam lamp forward to turn on, press the low beam lamp backward to turn on. 2.Horn button: Press the horn button to start the horn.
- Page 12 Right switch group Throttle Rotate counterclockwise to accelerate, rotate clockwise to decelerate. Reset after loosening, the motor stops outputting power. Fully off(Zero speed) Light switch group P gear Fully open(Maximum speed) Front brake lever 1.Light switch group: When the power lock is open, pushing The front brake lever is located on the right handlebar.
- Page 13 Main stand Side stand The main stand is located at the bottom of the center of The side stand is located on the lower left side of the the scooter. When using the main stand to park, the left scooter. When parking with the side stand, hold the hand holds the rear brake lever tightly to prevent it from rear brake lever tightly with your left hand to prevent it moving, the right hand holds the left position of the...
- Page 14 Inspection before riding Damage or contamination of the reflector and the license Inspection of power supply circuit and lighting circuit 1.Check whether the reflector is dirt and damaged and do not use it if there is dirt or damage. 1.Turn on the power supply, operate the lighting switch, 2.Check whether the license plate is firmly installed, and check whether the headlights and taillights are on the number is clear, and there is no dirt or damage.
- Page 15 Inspection of tire Correct driving Start and driving 1.Whether the tire pressure is normal. According to the depression of the tire grounding part, judge whether 1.Insert the key into the electric door lock, turn the power the air pressure is appropriate. If the air pressure is switch clockwise to turn on the whole vehicle circuit.
- Page 16 3.When parking, stand on the left and flat ground, it shall immediately stop operation and send it to the propping up the support. authorized repair shop designated by YADEA for 4.When you leave the scooter, Please be sure to lock the repair and replacement.
- Page 17 Therefore, in winter or cold areas, it is authorized repair shop designated by YADEA for repair normal when the continuous distance after one charge and replacement.
- Page 18 Remove the battery to charge Battery temperature 1.Do not touch the positive and negative electrodes of Charging operating temperature: 0 ~45℃ the battery with metal conductors. Discharging operating temperature: -20 ~ 50℃ 2.It is forbidden to charge the battery under the Storage temperature: -20 ~ 45℃...
- Page 19 Methods and cautions to effectively Use and maintenance of the charger improve battery life This charger is specially designed for YADEA electric scooter battery, which takes good care of the battery and 1.When accelerating, rotate the throttle slowly and not effectively improves the service life of the battery.
- Page 20 8.During the use and storage of the charger, attention 5.INSPECTION, MAINTENANCE AND REPAIR should be paid to avoid the entry of foreign matters, Dear customers: especially water or other liquids, so as not to cause short Please check and maintain the scooter regularly . when circuit inside the charger.
- Page 21 Inspection of the wheels Inspection of tire 1.Check whether the wheels rotate smoothly, whether 1.With the tire cooling, check with the tire pressure gauge. there is abnormal noise, and whether the front and 2.Check whether there are obvious cracks and damages on rear wheel fixing screws are tightened.
- Page 22 Maintenance and usage of flywheel Adjustment of handlebar and 1.Please make sure the lubrication of flywheel when saddle(if applicable) using the new vehicle. When adjust the handlebar and saddle, do not exceed the 2.Clean the flywheel every 3 month regularly, and use safety score line on the handlebar and saddle tube.
- Page 23 flexibly. If not, please go to YADEA authorized service station to replace add an appropriate amount of No.20 oil to the rotating brake pads of the same model.
- Page 24 3.After replacing the headlamp, adjust the headlamp the brake pad is worn or the brake system leaks. Please beam if necessary. go to YADEA authorized service station for inspection Replacement of fuse and maintenance. Add brake fluid or replace brake pads, Turn off the power supply and check whether the fuse please use the same model.
- Page 25 Users self-inspection items Schedule of maintenance contents for regular maintenance projects Inspection items 180days Everyday 60days 360days Inspection items Inspection contents 1.Whether the handlebar rotates and steering parts are loose and worn. Headlight, Turning lights, Taillight, Whether it works normally. 2.Whether the pedal parts are worn or not and Brake light whether the rotation is flexible.
- Page 26 Trouble shooting list 6.Specification Failure phenomena Failure reason and troubleshooting methods Electric schematic diagram ●Power lock failure: Repair or replace the power lock or plug-in. The scooter is not powered on ●Fuse open: Find out the reason and replace the fuse. ●Poor circuit contact: Retighten the power lead plug.
- Page 27 Specification 7.Maintenance Record Model Malfuntion Malfuntion Service Date Serviced by Remarks 1642×684×1038mm Description Description Station Dimension Wheel base(mm) 1161mm 55kg Rated load 75kg Brake system F: disc R: drum Motor type DC Brushless Rated motor voltage Rated motor speed 300 r/min Rated motor power 400W 48V24Ah...
- Page 28 Maintenance Record Malfuntion Malfuntion Service Date Serviced by Remarks Description Description Station...