SystemAir AW Series Installation And Operating Instructions Manual
Axial fans
Hide thumbs
Also See for AW Series:
- Operating and maintenance instructions manual (32 pages) ,
- Manual (6 pages) ,
- Manual (16 pages)
Related Manuals for SystemAir AW Series
Summary of Contents for SystemAir AW Series
- Page 1 Axial Fans AW, AR Installation and Operating Instructions Document in original language | · 003...
- Page 2 © Copyright Systemair AB All rights reserved E&OE Systemair AB reserves the rights to alter their products without notice. This also applies to products already ordered, as long as it does not affect the previously agreed specifications. | 003...
-
Page 3: Table Of Contents
Contents General information .........1 11.3 Maintenance ........13 11.4 Spare parts ......... 14 Notice symbols ........1 12 Cleaning ............14 1.1.1 Instruction symbols.....1 Important safety information ......1 12.1 Safety information........ 14 12.2 Procedure........... 14 Personnel ..........1 13 Deinstallation/dismantling....... 14 Personal protective equipment....2 5 rules of electrical safety ......2 14 Disposal ............ -
Page 5: General Information
General information | General information Notice symbols Danger Caution Hazard with a low risk Direct hazard Failure to comply with this warning may lead to Failure to comply with this warning will lead moderate injuries. directly to death or to serious injury. Important Warning Hazard with risk of damage to objects... -
Page 6: Personal Protective Equipment
Further prerequisites are a completed maintenance plan with no gaps and a commissioning re- port. Systemair will require these in the case of a warranty claim. The commissioning report is a component of this document. The maintenance plan must be created by the operator, see section 11.3 Maintenance, page 13. -
Page 7: Transport
The motor data can be found on the name plate of the motor, or in the technical documents of the motor manufacturer. Intended use • Systemair axial fans of the series AR and AW are exclusively designed as a built-in device for conveying air according to its technical data. | 003... -
Page 8: Incorrect Use
| Name plate and type key Incorrect use Incorrect use refers mainly to using the fan in another way to that described. The following uses are incorrect and hazardous: • Conveying of abrasive, explosive, combustible air or • Operation without duct system or protection grille air with solid particles. -
Page 9: Installation
Installation | Installation Safety information Warning: Danger from falling fan or fan parts. ♦ Check the surface before installation for load bearing capacity. ♦ Consider all static and dynamic loads when selecting hoisting equipment and fastening components. General safety information ♦... -
Page 10: Electrical Connection
| Electrical connection Electrical connection Safety information Danger: Electrically charged device Danger: Voltage on the device Risk of electric shock Risk of electric shock ♦ When working on an electrically charged device, ♦ Always connect a protective earth first. stand on a rubber mat. ♦... - Page 11 Electrical connection | Table 3 Description of electrical connections of the following fans: AW 200 EC sileo (#35854), AW 250 EC sileo (#35855), AW 300 EC sileo (#35857), AW 350 EC sileo (#35859)AW 400 EC sileo (#35860), AW 450 EC sileo (#35863) Wire Function/assignment...
- Page 12 | Electrical connection Table 4 Description of electrical connections of the following fans: AW 500 EC sileo (#35865), AW 500D EC (#35866), AW 560D EC sileo (#35867) Wire Function/assignment Connection Protective conductor Power supply, see name plate for voltage range Power supply, see name plate for voltage range 1, 2* N, L*...
-
Page 13: Protective Grounding Wire
Electrical connection | Table 5 Description of electrical connections of the following fans: AW 630D EC sileo (#35872), AW 710D-L EC sileo (#35876), AW 800D EC sileo (#35879), AW 1000D EC sileo (#35899) Wire Function/assignment Connection Protective conductor Power supply, see name plate for voltage range Status relais, open for failure Status relais, changeover contact, common connection (2 A, max. -
Page 14: Protecting The Motor
| Commissioning Protecting the motor Note: In fans equipped with an EC motor, there is no additional motor protection needed. The motor protection is integrated in the electronics of the motor. Important Damage to motor due to overcurrent, overload or short circiut. ♦... -
Page 15: Safety Information
Operation | Safety information ♦ Commissioning may only be carried out by adequately qualified persons, details see Table 1 Qualifications, page 1. ♦ Wear protective equipment during all work in the vicinity of the fan, details see 2.2 Personal protective equipment, page 2. -
Page 16: Troubleshooting/Maintenance/Repair
Thermal contacts/ resistors have Check the cooling impeller (if used), measure the motor Motor overheated triggered winding (if possible) / contact Systemair. Capacitor (if used) not or not Connect the capacitor correctly. correctly connected. Contact Systemair Motor blocked... -
Page 17: Maintenance
Ambient temperature too high Check if the correct fan is used for your application. Note: For all other damage/defects, please contact Systemair. Defective safety-relevant fans (for Ex and smoke extraction applications) must be replaced completely. 11.3 Maintenance Warranty claims can only be made if maintenance work is carried out correctly and written evidence thereof is provided. -
Page 18: Spare Parts
Check the flexible connectors for damage. See normal operating conditions Note: For all other damage/defects, please contact Systemair. Defective safety-relevant fans (for Ex and smoke extraction applications) must be replaced completely. 11.4 Spare parts ♦ Use original spare parts from Systemair only. -
Page 19: Commissioning Report
Commissioning Report | Commissioning Report Warranty claims can only be made if commissioning work is carried out correctly and written evidence thereof is provided. Description: Article no.: Manufacturing order no.: Installer Company: Contact person: Company address: Tel. no.: Email: Operator (Place of installation) Company: Contact person: Company address:... -
Page 20: Eu Declaration Of Conformity
□ □ Commissioning of the fan successful? Date, installer's signature Date, operator's signature EU Declaration of conformity The manufacturer: Systemair GmbH Seehöfer Straße 45 97944 Boxberg Germany Product designation: Axial fans Type designation: AXC; AXC (K); AXC (B); AXC (F); AXC-G; AXC (B)-G; AXC-P; AXC (B)-P; AXC-E; AXC-EK;... - Page 21 | 003...
- Page 22 Systemair GmbH Seehöfer Str. 45 97944 Boxberg Germany Tel.: +49 (0)7930/9272-0 Fax: +49 (0)7930/9273-92 info@systemair.de www.systemair.de...
Need help?
Do you have a question about the AW Series and is the answer not in the manual?
Questions and answers
RE: AW sileo 300EC can this model be used as ON/OFF---without external variable speed controlller?