Table of Contents
Advertisement
Quick Links
Maintenance & Parts Manual
All personnel associated with the administration of training, safety, operation and
maintenance of this equipment should read and familiarize themselves with the contents of
this manual.
☐ AMP50B
Safety, Operator,
☐ AMP70B
Mechanical Pulverizer
☐ AMP100B
Mechanical
Pulverizer
AMP50
AMP70
AMP100
B-Series
TM577330
Advertisement
Table of Contents
Related Manuals for Allied B Series
Summary of Contents for Allied B Series
- Page 1 Mechanical Pulverizer Mechanical Pulverizer AMP50 AMP70 AMP100 B-Series Safety, Operator, Maintenance & Parts Manual All personnel associated with the administration of training, safety, operation and maintenance of this equipment should read and familiarize themselves with the contents of this manual. ☐...
- Page 2 Revision History for Document No. TM577330 Continuous improvement of our products is an Allied policy. Allied reserves the right to change, edit, delete or modify the content of this document, including descriptions, illustrations and specifications without prior notification. The content of this publication describe the product at the time of its effective date, and may not reflect the product in the future.
- Page 3 Allied Construction Products, LLC www.alliedcp.com Safety Information Safety messages appear throughout this manual and Signal Words on labels affixed to the Allied equipment. Read and understand the information communicated in safety “DANGER”, “WARNING” and “CAUTION” are signal messages before any attempt to install, operate, words used to express severity of consequences service or transport the Allied equipment.
- Page 4 Pictograms are used to rapidly communicate information. For the purposes of this manual and Crush point labels affixed to the Allied equipment, pictograms are defined as follows: Read / Refer to the manual for Moving parts (in direction information indicated by arrow) ...
- Page 5 Lift Point – Marks approved lift points for safe handling of the work tool. LUBE POINT - Indicates location of lube fittings to be greased. Company Logo – The Allied brand identifier and is a registered trademark of Allied Construction Products, LLL.
- Page 6 Allied Construction Products, LLC www.alliedcp.com Safety Information – [cont'd] Information Labels – [cont'd] AMP50B 3900 KELLEY AVE. CLEVELAND, OHIO 44114 USA MECHANICAL PULVERIZER MODEL NUMBER SERIAL NUMBER YEAR WEIGHT, lbs. [kg] Minimum Recommended Carrier Weight, LBS. (kg.) labelloc15oct Fig. L-10 Label Positions Identified Table L.2 Label Ordering Information...
- Page 7 Allied equipment. Other manuals, such as those published by the machinery Locate existing underground service and utility used in support of the Allied equipment, should also lines be read. Erect barriers to prevent pedestrian access in to...
- Page 8 Operational Safety Program components. Reinstall all guards after service or adjustments are completed. The safe and efficient use of the Allied equipment depends upon proper installation, operation, Where it was not possible to prevent an unsafe maintenance and repair. Operational safety programs situation by means of a guard, safety messages must encompass all of these elements.
-
Page 9: Table Of Contents
Allied Construction Products, LLC www.alliedcp.com Table of Contents SECTION SECTION Document Revisions Contact Information…….. 7.0 Care and Maintenance……………………..… Safety Information……………..….………………… 7.1 Maintenance - General …………………….…… 7.2 Daily Maintenance……………………..…...…… Table of Contents……………………..……...…….. 7.2.1 Lubrication………………………..…………. 7.3 Daily Inspection…………….……………….….. 1.0 Introduction and Scope………………………. - Page 10 Allied Construction Products, LLC www.alliedcp.com Table of Contents – [cont'd] List of figures 10.1 Specifications………………….…………..….. S-1 Safety Alert Symbol…………………………….. 10.2 Dimension Diagrams………….…………..….. P Pictograms…………………………………………. 10.3 Dimension Diagrams………….………………. L-9 Label Locations…………………………………. 10.4 Dimension Diagrams………….…………..….. 2-1 Equipment Identification Tag……….…………. 11.1 Parts Identification………………..……………...
-
Page 11: Safety Information
Current Status See Inside Cover information as complete as possible. However, continuous improvement of our products is an Allied Product Name: Mechanical Pulverizer policy. The material in this publication, including Applicable Model[s]: MP50, 70 &... -
Page 12: Location Of Model And Serial Number
Copy the Model and Serial Number from the Equipment Identification Tag to the space provided below. Indicate the date in which the Allied equipment was placed into service. snloc15oct Figure 2-1 Equipment Identification Fill out the Warranty Registration form and return to Allied. -
Page 13: Warranty Protection Summary
The name and signature of the person Use the Allied attachment only if it is in sound performing the service, maintenance or operating condition. Take prompt action to rectify repair. TM577330_AMP_B series_15oct... -
Page 14: Allied Product Policies
3.3 Allied Product Policies In this manual, Allied recommends the use, applications, maintenance and service consistent with industry practices. Allied assumes no responsibility for the results of actions not recommended in this manual and specifically the results of: Improper installation, set-up, calibration ... -
Page 15: Product Description & Application
4.1 Mechanical Pulverizer The Pulverizer is designed for use with excavator type construction machinery. When installed, the Allied’s Mechanical Pulverizer is designed for machine's bucket cylinder is used to power the upper controlled demolition of concrete slabs, walls and jaw, while the lower jaw is held stationary by the stiff foundations. -
Page 16: Installation - General
Allied Construction Products, LLC www.alliedcp.com 5.0 Installation – General 5.1 Mounting the Pulverizer CAUTION The Allied Pulverizer utilizes pin-on type mounting The Pulverizer is designed for use with excavator arrangement. A set of mounting pins, bushings and type construction machinery. The carrier must have... -
Page 17: Pulverizer & Carrier Compatibility
Refer to Fig. 5-1 for a list of the mounting parts that the Allied work tool are discussed in Table 10.1. The are furnished with the Pulverizer assembly. Before provided ‘Minimum Carrier Weight’ is for general starting, check that all parts are on hand. -
Page 18: Mounting Pad Installation
Allied Construction Products, LLC www.alliedcp.com 5.0 Installation – General – [cont'd] Assistant: Check that the Pulverizer is stable and all 1. Position the stick as shown in Fig. 5-2. loads are supported. 2. Clean the area where the mounting pad will be... -
Page 19: Removal From Carrier
Allied Construction Products, LLC www.alliedcp.com 5.0 Installation – General – [cont'd] 7. Position stick section to remove the load from 5.5 Removal from Carrier Stick Pin. Remove Stick Pin. CAUTION NOTE: Reinstall mounting pins and hardware on Risk of eye injury from flying debris. -
Page 20: Operation
NOTE: To maximize the equipment’s service life, pay equipment. particular attention to correct working methods. The Allied Pulverizer is designed for controlled IMPORTANT demolition and recycling of concrete slabs, walls and Do not operate attachment beyond its performance foundations. -
Page 21: Operation
Allied Construction Products, LLC www.alliedcp.com 6.0 Operation – [cont'd] 2. With the attachment low to the ground, move carrier into the work zone. 3. Check ground conditions. Be aware of all obstacles such as slopes, ditches. Avoid unstable or slippery ground conditions. -
Page 22: Operation / Prohibited Actions
Allied Construction Products, LLC www.alliedcp.com 6.0 Operation – [cont'd] 6.2 Operation – Prohibited Actions Fig. 6-1 Protect Against Falling and Flying Debris. Do Not Use This Work Tool If Machine is Not Equipped with Approved Protective Structures, Guarding and Shields Fig. - Page 23 Allied Construction Products, LLC www.alliedcp.com 6.0 Operation – [cont'd] Fig. 6-4 Do Not Carry Loads Over the Machine or Over Workers Do Not Operate With Workers Inside Work Zone Fig. 6-5 Do Not Use Machine to Twist or Lever Objects Do Not Overload the Jaws.
- Page 24 Allied Construction Products, LLC www.alliedcp.com 6.0 Operation – [cont'd] Fig. 6-7 Do Not Overload Beyond Capacity Which Could Lead to Tipping. Carry Loads Close to Ground Level Avoid Operating / Travelling Across Slope Clear All Obstacles In Path of Machine...
-
Page 25: Lubrication
Allied Construction Products, LLC www.alliedcp.com 7.0 Maintenance and Service When properly installed, operated and maintained by qualified personnel, the Allied Pulverizer requires a minimum of service. Service intervals are to be used as a guide. Service should be performed more frequently as determined by operating conditions. -
Page 26: Bearing Inspection
IMPORTANT Modifications may create unwanted safety hazard or impair the function and performance of the Allied work tool. Do not make any alterations without written authorization from the Allied Engineering Department. When making repairs, use only the Fig. -
Page 27: Tooth Replacement
Allied Construction Products, LLC www.alliedcp.com 7.0 Maintenance and Service – [cont'd] 1. Position Pulverizer on flat, stable surface. 7.7 Threaded Fasteners 2. Loosen and remove nuts that secure the cutter IMPORTANT blade to holder. Keep fasteners tight. Replacement fasteners must be the same size, type and grade. - Page 28 Allied Construction Products, LLC www.alliedcp.com 7.0 Maintenance and Service – [cont'd] 7.8.2 Preheat Table 7.2 Build-up Material Shielded Metal, Arc Stick E7018, E8018-C3 Preheat general surrounding area to Electrodes: approximately 200F (100C) to remove any Gas Metal Arc, Solid Wire ER70S moisture.
-
Page 29: Tooth Hard Surfacing
Allied Construction Products, LLC www.alliedcp.com 7.0 Maintenance and Service – [cont'd] Grind the edges square to match the template CAUTION profile. Do all work in a well-ventilated area. Dispose of paint and solvent properly. 7.8.9 Hard-surface Procedure for Tooth... - Page 30 Allied Construction Products, LLC www.alliedcp.com 7.0 Maintenance and Service – [cont'd] 7.8.10 Pulverizer Jaw Build-Up and Hard- Surfacing Surrounding areas of the lower and upper jaw can be built-up and hard-surfaced to increase life. IMPORTANT The build-up and hard-surface procedure must be performed when there is adequate time for the jaw to cool slowly prior to use.
- Page 31 Allied Construction Products, LLC www.alliedcp.com 7.0 Maintenance and Service – [cont'd] Refer to the figure for areas approved for hard- surfacing. Area 1. Tooth Area 2. Crosshatch Jaws Area 3. Stringers at Plates / Blade Holders Serious damage and reduced life will result if hard-surfacing is applied to unapproved area.
- Page 32 Allied Construction Products, LLC www.alliedcp.com 7.0 Maintenance and Service – [cont'd] Apply two stringers to all four edges on top plate. Crosshatch the plate of the upper jaw at 45° angles to form 1” squares. Crosshatch the upper jaw at 45° angles to form 1” squares. Apply to outside and inside surfaces.
-
Page 33: Lifting & Transport
Be sure to use sturdy tie down equipment to secure load. 8.1.1 If the attachment is to be transported independent of the carrier; Remove all loose debris from the Allied Pulverizer. Follow removal instructions in Section 6.4. ... -
Page 34: Troubleshooting
9.0 Troubleshooting The Troubleshooting guide is designed to help CAUTION diagnose possible causes of several commonly When working with the Allied equipment all encountered conditions. For conditions other than procedures and operations must be performed these, contact the Allied Technical Service correctly so that unsafe situations may be avoided. -
Page 35: Technical Data
Allied Construction Products, LLC www.alliedcp.com 10.0 Technical Data Table 10.1 General Specifications MP50B MP70B MP100B Service Weight lbs. [kg] 3,920 [1,778] 4,660 [2,113] 6,780 [3,075] Minimum 22 [20] 33 [30] 42 [38] Recommended Carrier Weight ton [metric-t] Maximum 33 [30]... -
Page 36: Dimension Diagram
Allied Construction Products, LLC www.alliedcp.com 10.0 Technical Data – [cont'd] Table 10.3 Dimension Diagram Fig. 10-3 Item Description inch [mm] MP50B MP70B MP100B Stick 18.63 [473] 18.63 [473] 20.31 [516] Inside Width (max) Link 18.63 [473] 18.63 [473] 20.31 [516] Link 4.33 [110]... -
Page 37: Stiff Arm & Mounting Pad
Allied Construction Products, LLC www.alliedcp.com 10.0 Technical Data – [cont'd] Table 10.4 Dimension Diagram Fig 10-5 Stiff Arm & Mounting Pad Item Description Inch [mm] MP50B MP70B MP100B Length 48.62 [1235] 56.50 [1435] 66.14 [1680] Pin Ctr-Ctr Stiff Arm Pin Diameter 2.83 [72]... -
Page 38: Parts Information
Stationary 11.1 General This section provides spare parts information for the Allied equipment described in Section 1. When ordering mounting parts, it's important to provide information about the carrier to determine their correct size. The figures, tables and descriptions contained in this... -
Page 39: Parts Identification
Allied Construction Products, LLC www.alliedcp.com 11.0 Spare Parts Information – [cont'd] Spare Parts Information – [cont'd] Fig. 11-2 MP- B-Series Parts Identification Table 11.1 Parts Identification Part Number Item Description MP50B MP70B MP100B 1-23 Mechanical Pulverizer – Standard Assembly 577000C... -
Page 40: Parts Identification
Allied Construction Products, LLC www.alliedcp.com 11.0 Spare Parts Information – [cont'd] Fig. 11-3 MP- B-Series Parts Identification Table 11.2 Parts Identification Part Number Item Description MP50B MP70B MP100B 1-23 Mechanical Pulverizer – Standard Assembly 577000C 577005C 577010C Bushing - Main Pivot... - Page 41 Allied Construction Products, LLC www.alliedcp.com 11.0 Spare Parts Information – [cont'd] Your local Allied dealer requires the Product Name, Model Product Mechanical Pulverizer – B Series and Serial Number to better assist you with questions regarding parts, warranty, operation, maintenance, or Model repair.
- Page 42 NOTES TM577330_AMP_B series_15oct...
- Page 43 TM577330_AMP_B series_15oct...
Need help?
Do you have a question about the B Series and is the answer not in the manual?
Questions and answers