Displaying Information (Status Display) - Toshiba TLP-WX2200U Owner's Manual

Using the menus (Continued)
Default setting 2 menu
Item
Projection
Sets projection mode in accordance with Placement Style.
mode
(Standard)
Fan mode Sets the cooling fan speed.
Remote When two or more projectors are used and controlled by the remote
control control respectively, this menu sets the code for the projector and the
remote control.
[ or : Enter setting mode]
[ :Confirm] [
Press [Cancel] to return.
Key lock Lock the control panel buttons.
[ or : Enter setting mode]
[ :Confirm] [
Press [Cancel] to return.
Reset all Press . (The password and user logo are not reset.)
Resets all adjustments and settings to their factory settings.
Password Password setting
p.32
Detailed description
[Fan mode]
Setting [Fan mode] to [High] increases the cooling fan speed. (The cooling fan
noise gets louder.) Set this option to use the projector, for example, at high altitude
(over 1,500 meters above sea level).
• Do not set Fan mode to [High] when using the projector at a lower altitude.
[Remote control]
Sets a remote control code from 4 types. You can set each code respectively for up
to 4 projectors. The factory setting is [1].
To switch codes, set the same code for the projector and the remote control.
A remote control code is applied after the setting is done.
• You cannot operate the remote control if the codes of the projector and the
remote control do not match.
Remote control code setting for remote control
Remove the battery cover and set the same remote control code switch as the
projector. p.16 p.17 (Use a screwdriver with thin tip to set.)
Description
p.21
(Rear) (Ceiling) (Rear ceiling)
Standard
[ : Select from 1, 2, 3, 4]
:Select OK to end]
[ : Select On/Off]
:Select OK to end]
Yes
42
[Key lock]
Protect from operating errors by locking on the control panel buttons of the
projector. (The remote control operations are available.)
Control panel operations are locked after the setting is done, and accordingly
operation with the control panel buttons is disabled.
• To release the key lock, set the [Key Lock] to [Off] using remote control. Pressing
High
the [RETURN] button on the projector for 10 seconds also sets the [Key Lock] to
[Off]. (When operating the main unit, the 2 indicators of LAMP and TEMP light in
orange for 3 seconds, and at the same time the projector beeps.)

■ Displaying Information (Status display)

This displays information about the input signal, lamp use time, etc.
Item
Projector
Input
Mode name
Resolution
No
Frequency
Sync
Signal format
Video mode
Lamp time
Lamp reset count The count for lamp replacement
Total time
Version
Notes
1: The mode of supported RGB signals
2: Sync signal polarity shown as P (positive) or N (negative) for [H/V].
3: Displays [Lamp time] as a measure of when the lamp should be replaced. (Cannot be used as
a counter of guaranteed lamp time.) Please replace the lamp after 2000 hours of use if [Lamp
power] is set to [Standard], or after 3000 hours of use if [Lamp power] is set to [Low], consult
with a dealer about getting replacement for lamp TLPLW11 (sold separately).
4: [Version] shows the version of the projector's internal control program. This version is referred
to for customer service, etc.
Note
• The displayed information will not be refreshed if the status changes. To refresh the
information, dismiss the display, then display it again.
"Yes": displayed, "No": not displayed
Description Computer Y/P
Input source name
RGB input mode [Note 1]
Resolution (in dots)
Sync frequency
[Note 2]
Sync signal polarity
Y/P /P signal format
B R
Color method of video signal
Time of lamp use [Note 3]
The total time that this projector is used.
Firmware version [Note 4]
p.52 is shown.
43
/P Video S-video
B R
Yes Yes Yes Yes
Yes No No No
Yes No No No
Yes No No No
Yes No No No
No Yes No No
No No Yes Yes
Yes Yes Yes Yes
Yes Yes Yes Yes
Yes Yes Yes Yes
Yes Yes Yes Yes