Table of Contents
Advertisement
Quick Links
MANUAL
Installation / Operation / Maintenance
Flange STD：ANSI 150, PN10/16, JIS 10K
Temp. ：-20℃~120℃
Work Pres. ：10 / 16 BAR：DN40~DN600
10 BAR：DN650~DN1200
Pd. Date ：2017.1.13
Please Read All Of This Instruction Before
Installing Your 3530/353333/737 Valve
KLINGER Denmark A/S | Nyager 12-14, DK-2605 Broendby | T +45 43 64 66 11 | www.klinger.dk
Advertisement
Table of Contents
Related Manuals for KLINGER 3530
Summary of Contents for KLINGER 3530
- Page 1 Temp. ：-20℃~120℃ Work Pres. ：10 / 16 BAR：DN40~DN600 10 BAR：DN650~DN1200 Pd. Date ：2017.1.13 Please Read All Of This Instruction Before Installing Your 3530/353333/737 Valve KLINGER Denmark A/S | Nyager 12-14, DK-2605 Broendby | T +45 43 64 66 11 | www.klinger.dk...
-
Page 2: Product Life Cycle
Epdm 40 - 50 65 – 200 250 – 300 350 – 600 III* * Category I, II and III require CE mark KLINGER Denmark A/S | Nyager 12-14, DK-2605 Broendby | T +45 43 64 66 11 | www.klinger.dk... -
Page 3: Storage Condition
If the valve remains unpacked for a long duration, dust and any foreign materials may enter the seat, which may cause seat leakage. KLINGER Denmark A/S | Nyager 12-14, DK-2605 Broendby | T +45 43 64 66 11 | www.klinger.dk... -
Page 4: Installation
Check and see any distortion of the piping flange, misalignment, and damage to the gasket surface of the flange. KLINGER Denmark A/S | Nyager 12-14, DK-2605 Broendby | T +45 43 64 66 11 | www.klinger.dk... - Page 5 Before tightening the piping bolts, make sure the disc at an opened position and does not interfere with the flange. Tighten the piping bolts with a torque not higher than the torque shown in following table. KLINGER Denmark A/S | Nyager 12-14, DK-2605 Broendby | T +45 43 64 66 11 | www.klinger.dk...
- Page 6 “F” wrench on the hand-wheel. Unlike gate valves or glove valves, no torque tighten is required. Do not release the piping bolts before de-pressure the pipe system. KLINGER Denmark A/S | Nyager 12-14, DK-2605 Broendby | T +45 43 64 66 11 | www.klinger.dk...
-
Page 7: Maintenance
Put a match mark on disc before pull out the pins. c. Pull out the upper stem and bottom stem. d. Take out the disc and liner from the body. KLINGER Denmark A/S | Nyager 12-14, DK-2605 Broendby | T +45 43 64 66 11 | www.klinger.dk... - Page 8 Insert the pin to the lower stem, then put on O-ring seal and bottom cover and tighten. Reassemble the actuator and adjust the open and close position. KLINGER Denmark A/S | Nyager 12-14, DK-2605 Broendby | T +45 43 64 66 11 | www.klinger.dk...
- Page 9 If the wall and disc thickness has reduced by 25%, the valve must be replace. For the supply of genuine Value spares or technical assistance contact KLINGER Denmark A/S KLINGER Denmark A/S | Nyager 12-14, DK-2605 Broendby | T +45 43 64 66 11 | www.klinger.dk...
- Page 10 Page 9 of 14 Operating Manual Issue Date 1, 13, 2017 Edition Installation，Operation & Maintenance Instructions Number 73_-O 3530/3533/VF-73_ Series IRON Body 2”~12” KLINGER Denmark A/S | Nyager 12-14, DK-2605 Broendby | T +45 43 64 66 11 | www.klinger.dk...
- Page 11 Page 10 of 14 Operating Manual Issue Date 1, 13, 2017 Edition Installation，Operation & Maintenance Instructions Number 73_-O 3530/3533/VF-73_ Series Steel Body 2”~12” KLINGER Denmark A/S | Nyager 12-14, DK-2605 Broendby | T +45 43 64 66 11 | www.klinger.dk...
- Page 12 Page 11 of 14 Operating Manual Issue Date 1, 13, 2017 Edition Installation，Operation & Maintenance Instructions Number 73_-O 3530/3533/VF-73_ Series Iron Body 14”~24” KLINGER Denmark A/S | Nyager 12-14, DK-2605 Broendby | T +45 43 64 66 11 | www.klinger.dk...
- Page 13 Page 12 of 14 Operating Manual Issue Date 1, 13, 2017 Edition Installation，Operation & Maintenance Instructions Number 73_-O 3530/3533/VF-73_ Series Steel Body 14”~24” KLINGER Denmark A/S | Nyager 12-14, DK-2605 Broendby | T +45 43 64 66 11 | www.klinger.dk...
- Page 14 Page 13 of 14 Operating Manual Issue Date 1, 13, 2017 Edition Installation，Operation & Maintenance Instructions Number 73_-O 3530/3533/VF-73_ Series 26”~36” KLINGER Denmark A/S | Nyager 12-14, DK-2605 Broendby | T +45 43 64 66 11 | www.klinger.dk...
- Page 15 Page 14 of 14 Operating Manual Issue Date 1, 13, 2017 Edition Installation，Operation & Maintenance Instructions Number 73_-O 3530/3533/VF-73_ Series 38”~48” KLINGER Denmark A/S | Nyager 12-14, DK-2605 Broendby | T +45 43 64 66 11 | www.klinger.dk...
Need help?
Do you have a question about the 3530 and is the answer not in the manual?
Questions and answers