Technical Data - EINHELL BT-LC 500 Original Operating Instructions

Anleitung_BT_LC_500_SPK7__ 22.08.12 10:14 Seite 17
Keep the noise emissions and vibrations to a
minimum.
Only use appliances which are in perfect working
n
order.
Service and clean the appliance regularly.
n
Adapt your working style to suit the appliance.
n
Do not overload the appliance.
n
Have the appliance serviced whenever
n
necessary.
Switch the appliance off when it is not in use.
n
The quoted values are emission values and not
necessarily reliable workplace values. Although there
is a correlation between emission and immission
levels it is impossible to draw any certain conclusions
as to the need for additional precautions. Factors
with a potential influence on the actual immission
level at the workplace include the duration of impact,
the type of room, and other sources of noise etc.,
e.g. the number of machines and other neighboring
operations. Reliable workplace values may also vary
from country to country. With this information the
user should at least be able to make a better
assessment of the dangers and risks involved.

5. Technical data

AC motor:
Power P:
Power P:
Protection type:
Idle speed n :
0
Saw blade:
Max. cutting capacity (reversing cut):
Min. cutting capacity:
Max. material length:
Min. material length:
Weight:
A load factor of S2 10 min (intermittent periodic duty)
means that you may operate the motor continuously
at its nominal power level (2200 W) for no longer than
the time stipulated on the specifications label (10
minutes ON period). If you fail to observe this time
limit the motor will overheat. During the OFF period
the motor will cool again to its starting temperature.
6. Before starting (Fig. 1-8, 10, 12)
Do not start the machine until you have made
n
yourself familiar with these operating
instructions and all the safety instructions. If
you have no experience in handling these
machines, you should obtain assistance from
an experienced person.
Unpack the saw and check it for damage which
n
may have occurred in transit.
Attach the wheels (A) with safety splints (B) on the
n
shaft (C) then attach the wheel covers (D).
Spring mechanism: Secure the guide rod (I) of the
n
spring mechanism with the cross-bolt (E), the
washers (F, G) and the locknut (H). Then slip on the
spring (M) and the rubber bushing (L). Swing the
feed carriage shut and fasten the guide rod with the
split pin.
Secure the guide rod with the stop washer (J) and
the locknut (K).
Fit the length stop (5) and the carriage extension
n
(7).
Attach the cover plate (16).
n
Important: Each time the machine is started,
make sure beforehand that the self locking
nuts (H,K) for the cross bolts and guide rods
are attached (Fig.6).
The machine may only be used outdoors. The
n
machine must be placed on a horizontal, even
230 V ~ 50 Hz
base and be firmly anchored to the ground using
1600 W S1 the mounting holes (10) in the machine foot. The
ground around the machine must be clear of
2200 W S2 10 min
waste, slippery areas and stumbling blocks.
IP 54
All covers and safety equipment must be properly
n
2850 rpm installed and the saw blade must run freely.
Check the entire machine and al cables for any
n
Ø 450 x Ø 30 x 3.0 mm
signs of transport damage.
190 mm
Check that the saw blade is secured, not dirty,
n
undamaged and sharp. Sharpen or replace blunt
30 mm
saw blades.
1100 mm
Check that all the screw connections are tight.
n
100 mm
Test slot inserts (12) for wear and if necessary,
n
exchange these.
58 kg
The feed cradle must be returned to its original
n
position automatically by the spring.
Check the machine for any foreign bodies that
n
may be catapulted out of it.
The power source must be protected by an RCCB
n
with a fault current of 30 mA.
Check that the voltage on the rating plate is the
n
same as your supply voltage before you connect
the machine to the power supply.
Important: It is essential that other persons
n
remain a safe distance from the saw whilst it is
operating.
Do not attempt to saw more than one piece of
n
GB
17