BKI FW-12 Quick Start Manual
Fry warmer
Hide thumbs
Also See for FW-12:
- Service manual (36 pages) ,
- Service manual (37 pages) ,
- Operation manual (13 pages)
Subscribe to Our Youtube Channel
Related Manuals for BKI FW-12
Summary of Contents for BKI FW-12
- Page 1 MODE D’EMPLOI Fry Warmer MODÈLES FW-12, FW-15, FW-12T, FW-15T, FW-15DTO Date de fabrication Avril, 2019 et au-delà SS-OM-025F.02 Revised 9/2/2020...
- Page 2 PIÈCES DE RECHANGE Les pièces FEO de l'usine BKI bénéficient d'une garantie de 90 jours sur les matériaux à partir de la date de l'installation par un centre de service agréé par l'usine BKI.
-
Page 3: Table Of Contents
Installation ................................. 5 Instructions for Shipping Damage .......................... 5 Electrical Information and Grounding ........................5 Installation Instructions ............................5 FW-12 & FW-12T (Side Breather) ........................5 FW-15 (Side Breather) ............................6 FW-15 (Bottom Breather) ........................... 7 FW-15T/FW-15DTO (Bottom Breather) ......................9 Operation ................................ -
Page 4: Introduction
BKI. The BKI name and trademark on this unit assures you of the finest in design and engineering — that it has been built with care and dedication — using the best materials available. Attention to the operating instructions regarding proper installation, operation, and maintenance will result in long lasting dependability to insure the highest profitable return on your investment. -
Page 5: Pratiques D'interventions Sûres
étiquettes de sécurité sur cette unité. Si vous avez besoin d'étiquettes de sécurité neuves, obtenir le numéro de l'étiquette illustrée à la page 6, puis téléphoner au service technique BKI : BKI Amérique du Nord : (802) 658-6600. -
Page 6: Étiquettes De Sécurité
Fry Warmer Introduction Étiquettes de sécurité... -
Page 7: Installation
BKI Fry Warmers are wired for use in accordance with all applicable local, state, and federal codes. For specific electrical requirements and connections refer to the wiring diagram attached to the unit or provided in the Service Manual. -
Page 8: Side Breather)
10. Fit pan insert to main unit by lifting the open side of pan insert over the two tabs on main unit and lower the pan insert into the opening in the adapter. Countertop Cutout (FW-12 & FW-12T) 1. Obtain a suitable countertop location for the unit that will provide a clearance of 4” from the side louvers. -
Page 9: Bottom Breather)
Fry Warmer Installation 10. Fit pan insert to main unit by lifting the open side of pan insert over the two tabs on main unit and lower the pan insert into the opening in the adapter. Countertop Cutout 1. Obtain a suitable countertop location for the unit that will provide a clearance of 4” from the side louvers. 2. - Page 10 Fry Warmer Installation 3. Using a 1/8” drill bit, drill holes in the countertop used to secure WB31216000 to the countertop. 4. Secure WB31216000 to countertop with # 8 sheet metal screws. 5. Seal WB31216000 to the countertop to conform to NSF Standard 4, Item 4.28. (Dow Corning RTV #732 Multi purpose Sealant.) 6.
-
Page 11: Fw-15T/Fw-15Dto (Bottom Breather)
Fry Warmer Installation 8. Position main unit on WB31211900. 9. Fit pan insert to main unit by lifting the open side of pan insert over the two tabs on main unit and lower the pan insert into the opening in the countertop. FW-15T/FW-15DTO (Bottom Breather) Countertop Collar Weldment With Liner Pan (WB31217700) 1. -
Page 12: Operation
Fry Warmer Operation Operation Unit Startup and Preheating 1. Turn on power to the unit. 2. Allow the equipment to preheat for ten (10) minutes before loading it with product. Operational Guidelines Foods should be a minimum of 195° F. before being placed in the warmer. •... -
Page 13: Maintenance
Fry Warmer Maintenance Maintenance Le non-respect de l’entretien indiqué ci-dessous pourrait donner lieu à un accident grave ATTENTION ou endommager l’équipement. Il pourrait y avoir électrocution, défaillance du matériel ou dégâts matériels si l’installation électrique est faite par un électricien non agréé. Veillez à ce qu’un électricien agréé effectue l’installation conformément aux codes national et local. -
Page 14: Troubleshooting
Refer to the table below for troubleshooting information. Problem Cause Possible Solution Warmer chute is not Ceramic heating Contact an authorized BKI service agent for holding heat element failure corrective action. Noisy fan Fan blade is dirty or fan Contact an authorized BKI service agent for bearings are failing corrective action. -
Page 15: Repair
Fry Warmer Maintenance Repair Before replacing any parts, make sure the power has been turned off and the unit has cooled down. Lamp Replacement Only use PTFE-coated lamp to prevent glass contamination. 1. Make sure power to the unit is OFF and the unit has cooled down. 2. -
Page 16: Notes
Fry Warmer Notes Notes... - Page 17 Fry Warmer Notes...
- Page 18 42 Allen Martin Drive, Essex Junction, VT 05495, USA http://www.bkideas.com Made and printed in the U.S.A...
Need help?
Do you have a question about the FW-12 and is the answer not in the manual?
Questions and answers