Toro Greensmaster TriFlex 3320 Operator's Manual page 20

P M
ROTECTED ENUS
P S
ROTECTION ETTINGS
R D
ESET EFAULTS
R D
AISE ELAY
L D
OWER ELAY
T D
APOFF ELAY
R S
EEL PEED
B
ACKLAP RPM
C C
LIP ONTROL
B C
LADE OUNT
C (FOC)
LIP
A
BOUT
Menu Item
M
ODEL
SN
TEC 5001
I C
NFO ENTER
CU1
CU2
CU3
G
ENERATOR
CAN B
US
Adjusting the Center Cutting Unit Raise/Lower Delay
Adjust the raise and lower delay time for the center
cutting with the InfoCenter, as desired from 1 to 10
according to the table below. The factory default
setting is 6 (375 ms) and is optimized for a 3.8 mph
mow speed.
Increment Number
1
Allows the distributor/engineer
to access protected menus by
inputting a passcode.
Controls the protected menus.
Resets the InfoCenter to
default settings.
Controls the raise delay time
for the center cutting unit.
Controls the lower delay for
the center cutting unit.
Controls the tap-off delay.
Controls the reel speed.
Controls the backlap rpm
speed.
Turns the automatic
clip-control feature O /O .
N FF
Set the number of blades in
each reel. This setting is only
necessary if C C
LIP ONTROL
set to O .
N
Sets the desired clip. This
setting is only necessary if
C C is set to O .
LIP ONTROL N
Description
Lists the model number of the
machine.
Lists the serial number of the
machine.
Lists the software revision of
the master controller.
Lists the software revision of
the InfoCenter.
Lists the software revision of
the first cutting unit.
Lists the software revision of
the second cutting unit.
List the software revision of
the third cutting unit.
Lists the serial number of the
generator.
Lists the machine
communication bus status.
Delay Time (Seconds)
0.100
2
3
4
5
6
7
8
9
10
Adjusting the Tap-off Delay
The tap-off delay feature allows the cutting units to
turn off without raising, and you may adjust it with
the InfoCenter. The delay setting represents the
maximum time for the raise/lower joystick to remain in
the raise position to activate this feature. The factory
is
default setting is 1 which disables this feature.
Increment Number
1
2
3
4
5
6
7
8
9
10
Setting the Clip-Control Feature
To achieve a consistent, high quality-of-cut and a
uniform after cut appearance, the machine has a
clip-control feature that varies the speed of the reels
with the speed of the machine, to maintain a constant
clip. This feature is O
turn it O as follows:
N
1. From the S
2. Set C C
LIP
3. From the S
4. Set the B
LADE
blades in each of your reels.
5. From the S
6. Set C (FOC) to the desired clip setting.
LIP
Setting the Reel Speed
The clip-control feature automatically sets the reel
speed to match the machine speed. If you choose
20
0.150
0.200
0.250
0.300
0.375
0.475
0.600
0.750
0.925
Delay Time (Seconds)
Off
0.050
0.100
0.150
0.200
0.250
0.300
0.350
0.400
0.450
by default; configure it and
FF
menu, select C
ETTINGS
to O .
ONTROL N
menu, select B
ETTINGS
C to match the number of
OUNT
menu, select C
ETTINGS
C .
LIP ONTROL
C .
LADE OUNT
(FOC)
LIP