Sony DWT-B30 Service Manual
  1. Manuals
  2. Brands
  3. Sony Manuals
  4. Transmitter
  5. DWT-B30
  6. Service manual

Sony DWT-B30 Service Manual

Digital wireless transmitter
Hide thumbs Also See for DWT-B30:
Table of Contents

Advertisement

Quick Links

DIGITAL WIRELESS TRANSMITTER
DWT-B30
利用条件: 
①  本情報はソニー製品の販売、設置、設定、使用の目的でのみご利用ください。かかる目的以外での利用を禁止します。
②  著作者の事前の書面による許可なく、本情報の全部または一部の複写、複製、転載、改変、翻訳、送信等を禁止します。
情報改訂:
本情報は、当社の裁量により、予告なく変更されることがあります。ご使用される場合、本情報が最新の情報であることを確認のうえ、
ご使用ください。
Conditions of Use:
(1) Please use this information only for the purpose of sales, installation, configuration, and use of Sony products. Using this information
for any purpose other than the purpose described foregoing is forbidden.
(2) Do not copy, replicate, reproduce, alter, translate, transmit, sell, lease, or distribute this information in whole or in part without the prior
written permission of the author.
Revision of Information:
This information may be changed or updated at any time without any prior notice. Please confirm that this information is up-to-date before
using it.
SERVICE MANUAL
1st Edition

Advertisement

Table of Contents
loading

Related Manuals for Sony DWT-B30

Summary of Contents for Sony DWT-B30

  • Page 1 ご使用ください。 Conditions of Use: (1) Please use this information only for the purpose of sales, installation, configuration, and use of Sony products. Using this information for any purpose other than the purpose described foregoing is forbidden. (2) Do not copy, replicate, reproduce, alter, translate, transmit, sell, lease, or distribute this information in whole or in part without the prior written permission of the author.
  • Page 2 électrique, d’incendie ou de blessure n’effectuer que les réparations indiquées dans le mode d’emploi à moins d’être qualifi é pour en effectuer d’autres. Pour toute réparation faire appel à une personne compétente uniquement. DWT-B30...
  • Page 3 Batterien nur durch den vom Hersteller empfohlenen Kasser batteriet i henhold til gjeldende avfallsregler. oder einen gleichwertigen Typ ersetzen. Wenn Sie die Batterie entsorgen, müssen Sie die Gesetze der jeweiligen Region und des jeweiligen Landes befolgen. 注意 注意 如果更换的电池不正确，就会有爆炸的危险。 只更换同一类型或制造商推荐的电池型号。 处理电池时，必须遵守相关地区或国家的法律。 1 (P) DWT-B30...

  • Page 5: Table Of Contents

    Water Detection Sheet........3-12 (E) 3-3-2. Sheet and Cushion .........3-13 (E) 3-3-3. Notes on Replacing the TX-172 Board ..3-14 (E) 3-3-4. Notes on Replacing the DPR-396 Board ..3-14 (E) 3-4. Checking when Replacing or Removing Parts ..3-15 (E) 1 (E) DWT-B30...
  • Page 6 RM-215 Board (Reference Nos. 2000 to 2999) ......7-2 (E) 7-2. Pin Description of CPU (IC402 on the DPR-396 Board) ........7-3 (E) 7-3. Block Diagrams ............... 7-5 Overall ................7-5 7-4. Frame Wiring..............7-6 Frame Wiring..............7-6 Revision History 2 (E) DWT-B30...

  • Page 7: Service Overview

    (Example) Destination: UC Destination Indication label of Indication of channel Indication of model name in model name plate this manual Japan (J) 13-36 DWT-B30/L (J) 29-53 DWT-B30/MH (J) 1.2L, 1.2M, 1.2H DWT-B30/G (J) North America 14-36, 38 DWT-B30 (UC) (UC)

  • Page 8: Required Tool

    2. Pull out the connector removal tool vertically in the direction of the arrow 2. 3. Remove the connector removal tool from the coaxial harness in the direction of the arrow 3. Connector removal tool Connector removal tool Coaxial harness Coaxial harness 1-2 (E) DWT-B30...

  • Page 9: Hexagonal Nut Of Antenna

    Part name: Bit (LEMO) tool (LEMO nut mounting tool) Part number: J-7121-650-A Use this tool together with the torque driver made by TOHNICHI or equivalent. Shape of the Unit: mm tip of driver 1-3 (E) DWT-B30...

  • Page 10: Water Detection Sheet

    The water detection sheet does not react to the dampness. It reacts only to the dew drop and water drop. Procedure after judgment When the water detection sheet is blurred, replace it referring to Section 3-3-1. 1-4 (E) DWT-B30...

  • Page 11: Item List In Test Mode

    Lights up all dots of the organic EL display. All lights during ALL LIGHT setting. FREQ 6MHz JUMP Changeable The transmit frequency of the RF circuit can be changed in units of 6 MHz. Not used for maintenance service. 1-5 (E) DWT-B30...
  • Page 12 GUARD PATTERN Changeable This is used for design and investigation. Not used for maintenance service. BATT TEMP Displays the battery voltage and internal temperature. PHANTOM Not used in this unit. FUNCTION PHANTOM ON/OFF Not used in this unit. 1-6 (E) DWT-B30...

  • Page 13: Troubleshooting

    2) Disconnection of AF harness: Replace the AF harness. (Refer to the Section 3-2-7.) 3) Failure of TX-172 board (failure of audio circuit): Replace the TX-172 board. 2-1-2. Remote Function Does Not Operate When the RF remote function does not operate, refer to “4-2-4. RF Remote Performance Check”. 2-1 (E) DWT-B30...

  • Page 14: Radio Wave Is Not Output

    Replacement procedure of TX-172 board: Check CN880 (TX-172 board)/CN1001 (CN-4088 board). Refer to Section 3-2-4. 2) Failure of CN-4088 board: Replace the CN-4088 board. (Refer to Section 3-2-6.) . 2.4 GHz remote Refer to “4-2-4. RF Remote Performance Check”. 2-2 (E) DWT-B30...

  • Page 15: Image Is Not Displayed On The El Display

    (Failure of power circuit) Possible causes 1) EL cable disconnetion: Replacement procedure of DPR-396 board: Check CN400 (DPR-396 board). Refer to Section 3-2-5. 2) Failure of organic EL display element: Replace the organic EL display element. (Refer to Section 3-2-5.) 2-3 (E) DWT-B30...

  • Page 16: Error Message

    XIIC ERROR ERROR CODE xx There is an abnormality in EEPROM Check if there is any abnormality in the path and (IC813) on the TX-172 board, and parts connected to the periphery of EEPROM the reading or writing has failed. (IC813). 2-4 (E) DWT-B30...

  • Page 17: Notes On Removing And Replacing The Main Parts

    . Nut (supplied with this unit) (SMA connector): 0.80 ?0.12 N.m . Special head screw (3ULR-F): 0.12 ?0.01 N.m . Antenna: 0.60 ?0.09 N.m When using the torque driver with the notation of cN.m, interpret it as follows. Example: 0.8 N.m = 80 cN.m 3-1 (E) DWT-B30...

  • Page 18: Disassembly

    B. 3-2-2. Antenna Required Tool . Bit (3ULR-F) tool (for mounting special head screw): Part number J-7121-640-A . SMA antenna mounting tool: Part number J-7121-660-A 1 Special head screw (P1.7 1.6) 2 Antenna 3-2 (E) DWT-B30...

  • Page 19: Case (Lower)

    3-2-3. Case (Lower) Workflow: Battery case assembly (Section 3-2-1) → Antenna (Section 3-2-2) → Case (lower) 1 LRT type machine screw (M2) 2 Five screws (M1.7 3 Case (upper) 4 Lid (USB) 3-3 (E) DWT-B30...

  • Page 20: Board

    CN4012. Do not block them. CN500 CN4002 Push the extra CN500 length of the harness CN4012 Twist the harness from CN4002 two and in this space. a half turns, then connect it to CN500. 3-4 (E) DWT-B30...

  • Page 21: Element

    ![ Four hooks 7 Sheet (USB) 1 Two screws (PSW1.7 3.5) 2 DPR-396 subassembly CN401 5 Harness 3 Power SW protection sheet 4 Knob (SW) 9 Button (2 gangs) CN404 6 Flexible flat cable 8 Button Notch 3-5 (E) DWT-B30...
  • Page 22 8 Secure the organic EL display element with the hooks [D] of the EL holder. Organic EL display element Organic EL display element Hooks [C] Hooks [D] 9 To install, reverse steps 1 to 9 in the removal procedure. 3-6 (E) DWT-B30...

  • Page 23: Cn-4088 Board

    (Section 3-2-5) → CN-4088 board 1 Screw 6 Coaxial cable (PSW1.7 3.5) 5 CN-4088 board 2 Bracket (ANT) 4 Washer (SMA) 3 Supplied nut (SMA connector) View on arrow A 6 Coaxial cable routing direction Coaxial cable CN-4088 board 3-7 (E) DWT-B30...

  • Page 24: Cn-4148 And Cn-4078 Boards

    !- Washer (B) Apply the locking compound 7 Supplied (1401B) to 1/4 of outer washer circumference. (Size of two 9 Connector (S) 4P grains of rice) 2 MIC bracket (Z) 0 Earth ring View on arrow A Harness (AF) 3-8 (E) DWT-B30...
  • Page 25 CN4002 Twist the harness from CN4002 two and 2 Screw a half turns, then connect it to CN500. (PSW1.7 3.5) 3 LEMO connector assembly CN4002 1 Harness (AF) 5 Cushion (O) 4 Supplied nut 6 Cushion (TX) 3-9 (E) DWT-B30...

  • Page 26: Board

    (Section 3-2-5) → CN-4148/4078 board (Section 3-2-7) → RM-215 board 4 Flexible flat cable C2001 C2002 3 RM-215 board 5 Coaxial cable 2 Spacer (P) 1 Screw (PSW1.7 3.5) Insulated side Valley fold Flexible flat cable Valley fold Insulated side 3-10 (E) DWT-B30...

  • Page 27: Battery Terminal Assembly

    3-2-3) → Battery terminal assembly 2 Battery terminal assembly 7 Battery spring (GND) 1 Harness (PWR) 6 Lead wire (black) 3 Two solders 4 Lead wire (red) 5 Battery spring (HOT) C2002 8 Sheet TX-172 board 9 Bracket (BS) 3-11 (E) DWT-B30...

  • Page 28: Notes On Replacement Of Parts

    2. Remove the TX-172 board. (Refer to Section 3-2-4.) 3. Remove the DPR-396 board. (Refer to Section 3-2-5.) The water detection sheet is divided into three sheets. Attach the divided sheet to each place. Water detection sheet (B) Case (upper) 3-12 (E) DWT-B30...

  • Page 29: Sheet And Cushion

    . Cushion (RM) and cushion (MIC) Back side of case (upper) Back side of case (lower) Reference Reference Reference Reference Cushions (RM) Cushion (MIC) Cushion (MIC) (CN, UC, G(J), MH(J)) . Protection sheet R sides Protection sheet Reference Reference 3-13 (E) DWT-B30...

  • Page 30: Notes On Replacing The Tx-172 Board

    TX-172 board (A side) MT mark COMPL mark Destination identifying silk pattern list MT mark COMPL mark Destination of board DWT-B30/L (J) DWT-B30/MH (J) DWT-B30/G (J) DWT-B30 (UC) DWT-B30/L (CE) DWT-B30/H (CE) DWT-B30 (CN) . Do not replace parts, but replace the TX-172 board so as to secure characteristics and quality when replacing IC802, IC805, IC807, IC813, IC815 and Q801.
  • Page 31 3-15 (E) DWT-B30...

  • Page 33: Electrical Alignment

    Used mainly for UC, CN and J destinations (HRS connector) Coaxial conversion connector (SMA-HSC) 1-842-449-11 RF signal measurement Sony DWR-R02DN or DWR-R03D that works This unit supporting each destination properly Sony ECM-77LM that works properly Used mainly for CE destination (LEMO...

  • Page 34: Performance Check

    AUTO OFF (When the organic EL is off) RF REMOTE: RF POWER: 10 mW INTERNAL SG: 1 kHz Power-supply voltage: Voltage between battery terminals: 3.0 V CODEC MODE: MODE 2 Specifications: Indication of DC ammeter = 205 mA or less 4-2 (E) DWT-B30...

  • Page 35: Rf Performance Check

    654.975 H (CE), CN G (J) 1240.025 1252.000 1264.000 RANGE 3 RANGE 4 L (J), (UC), 558.000 572.975 587.975 588.000 602.975 617.975 L (CE) MH (J), 655.000 669.975 684.975 685.000 699.975 714.975 H (CE), CN G (J) 4-3 (E) DWT-B30...
  • Page 36 4. To change RANGE, move the menu to EXIT, and then press the [SET] button. Then, change the frequency by performing the operations in steps 2 and 3. In the test mode, do not change each parameter. If it is changed, turn the power off and on again. 4-4 (E) DWT-B30...
  • Page 37 (5) Perform the above measurement steps (1) to (4) with each transmission power of 2 mW, 10 mW and 25 mW. Specifications: 25 mW setting 10 mW setting 2 mW setting 18.75 to 30 mW 5.12 to 7.68 mW 1.4 to 2.4 mW 4-5 (E) DWT-B30...
  • Page 38 3. Measurement of BER (bit error rate) In this measurement, the quality of the signal being transmitted is checked. Required equipment . Bit error rate mater . DWR-R02DN/R03D that works properly . DU-510 board (BER measurement tool) 4-6 (E) DWT-B30...
  • Page 39 DWR-R03D For the connection and setting procedures, refer to “Sensitivity Check” in the Service Manual of DWR- R03D. For the connection and setting procedures for the case of using DWR-R02N, refer to the Service Manual of DWR-R02DN. 4-7 (E) DWT-B30...
  • Page 40 . Spectrum analyzer Setting of measuring device . SPAN: 2 MHz . RBW, VBW: 1 kHz . LEVEL: 3 dBm (setting: 2 mW) 10 dBm (setting: 10 mW) 14 dBm (setting: 25 mW) . TRACE: Peak HOLD 4-8 (E) DWT-B30...
  • Page 41 (5) Check that the frequency (2 times, 3 times and 4 times the level of the transmission frequency) is within specification in the following frequency RANGE. RANGE 0: L ch _30 dBm or less (L (J) and L (CE), _36 dBm or less for UC model) Specification: 4-9 (E) DWT-B30...

  • Page 42: Audio Circuit Performance Check

    T.H.D + N ATT = 0 dB, _43 dBu, 1 kHz, Sin wave, LPF: <22 kHz 0.05 % or less For the connection and setting procedures for the case of using DWR-R02DN, refer to the Service Manual of DWR-R02DN. 4-10 (E) DWT-B30...

  • Page 43: Rf Remote Performance Check

    RM-215 board, go to 1. 3 Perform the pairing and check the remote For the operation procedure, refer to the Operating Instructions. operation. Replacement procedure of RM-215 board: Refer to Section 3-2-8. Go to the next page 4-11 (E) DWT-B30...
  • Page 44 Has the pairing been successful within 3 times? Succeeded. Not succeeded. Normal Go to the next step. Operation transmission power. Provide a distance of 1 m between the transmitter and receiver after the pairing is completed. Go to the next page 4-12 (E) DWT-B30...
  • Page 45 Failure of high frequency parts been checked. After replacement, check the transmission power again. How many condition levels are there from a distance of 1 m? Three Two or less The operation has been checked. Normal operation The check is completed. 4-13 (E) DWT-B30...

  • Page 46: Operation Check

    Place this unit and DWR-R03D close to each other (on the same table) so that they can perform communication, and then transmit the radio wave. 2. Check that the sound is output normally from the headphone. . No sound distortion . No noise . Volume without uncomfortable feeling 4-14 (E) DWT-B30...

  • Page 47: Radio Wave Check

    2. Perform the pairing of the microphone and DWR-R03D by referring to the Operating Instructions. 3. Check that the control can be performed using the remote function. If the paring is performed for the check procedure, the user’s pairing information is deleted. 4-15 (E) DWT-B30...

  • Page 49: Firmware Update

    For details on how to obtain it, please contact your local Sony Sales Office/Service Center. . The file name of the update software “DWT-B30 Flash Write” varies for each version. Check the latest version and install the software corresponding to it.

  • Page 50: Preparation In Advance (Windows 8/8.1 And Windows 10)

    When PC can connect to the Internet 1. Double-click setup.exe in the DWT-B30_Version_X_XX_Updater folder. 2. The following screen is displayed. Click the [Yes] button. 3. PC is connected to the site of Microsoft. Click [.NET Framework 3.5 SP1]. 5-2 (E) DWT-B30...
  • Page 51 4. Click the [DOWNLOAD] button. 5. Click the [Run] button. 6. Click [Download|and|install|this|feature]. 5-3 (E) DWT-B30...
  • Page 52 7. Check that the following screen is displayed. (The installation has been completed.) When PC cannot connect to the Internet 1. Set the Windows 8 installation disk to the DVD drive. 2. The startup screen is displayed. Right-click the mouse and click [All apps]. 5-4 (E) DWT-B30...
  • Page 53 “X” represents the drive name. Change it according to the use environment. The following illustration shows the case that the DVD drive is the E drive. 5. Check that the following screen is displayed. (The installation has been completed.) 5-5 (E) DWT-B30...
  • Page 54 Check procedure 1. Open the control panel and click [Uninstall a program]. 2. Click [Turn Windows features on or off]. 5-6 (E) DWT-B30...
  • Page 55 3. Check that [.NET Framework 3.5 (including .NET 2.0 and 3.0)] is marked. (The installation has been completed.) 5-7 (E) DWT-B30...
  • Page 56 Change of security setting In the case of Windows 8/8.1 1. Click [Settings] from the start menu. 2. The following screen is displayed. Click [Change PC settings]. 5-8 (E) DWT-B30...
  • Page 57 3. In the case of Windows 8 Select [General], and then click the [Restart|now] button in [Advanced startup]. In the case of Windows 8.1 Select [Recovery] in [Update and recovery], and then click the [Restart|now] button in [Advanced startup]. 5-9 (E) DWT-B30...
  • Page 58 4. After restarting, the following window is displayed. Click [Troubleshoot]. 5. Click [Advanced options]. 6. Click [Startup Settings]. 5-10 (E) DWT-B30...
  • Page 59 7. Click the [Restart] button. 8. After restarting, the following screen is displayed. Select [7) Disable driver signature enforcement]. 9. After startup, install the Updater and USB driver. (Refer to Sections 5-2-3 and 5-2-4.) 5-11 (E) DWT-B30...
  • Page 60 In the case of Windows 10 1. Click the [Start button], and then click [Settings]. 2. The following screen is displayed. Click [Update & security]. 3. Click [Recovery], and then click the [Restart|now] button in [Advanced startup]. 5-12 (E) DWT-B30...
  • Page 61 4. Restart PC. When the following screen is displayed, click [Troubleshoot]. 5. The following screen is displayed. Click [Advanced options]. 6. Click [Startup Settings]. 5-13 (E) DWT-B30...
  • Page 62 7. Click the [Restart] button. 8. After restarting, the following screen is displayed. Select [7) Disable driver signature enforcement]. 9. After startup, install the Updater and USB driver. (Refer to Sections 5-2-3 and 5-2-4.) 5-14 (E) DWT-B30...

  • Page 63: Installation Of Updater

    5-2-3. Installation of Updater 1. Double-click setup.exe in the DWT-B30_Version_X_XX_Updater folder. 2. The following screen is displayed. Click the [Next>] button. 3. Click the [Next>] button. 5-15 (E) DWT-B30...
  • Page 64 4. Click the [Next>] button. The installation is started. During the installation, a dialog relating to the user account control may be displayed. In this case, click the [Yes] button. 5-16 (E) DWT-B30...
  • Page 65 5. When the installation is completed, click the [Close] button. (The installation has been completed.) 5-17 (E) DWT-B30...

  • Page 66: Installation Of Usb Driver

    1. Connect this unit and PC with the USB cable. “Device driver software was not successfully installed” is displayed on the following screen. 2. Right-click [Computer] from the Windows menu, and then select [Properties]. 3. The following screen is displayed. Select [Device Manager]. 5-18 (E) DWT-B30...
  • Page 67 4. Right-click [Unknown device] in [Other devices], and then select [Update Driver Software...] from the context menu. 5. Click [Brows my computer for driver software]. 6. Click [Browse...] button. 5-19 (E) DWT-B30...
  • Page 68 7. Select C:\Program Files(*1)\Sony\DWT-B30 Version <X.XX> Updater(*2), and then click the [OK] button. *1) In the case of the 64-bit version of operating system, select Program Files (x86). *2) The model name and version vary depending on Updater. In this illustration, V1.03 is used.
  • Page 69 10. When the installation is completed, the following screen is displayed. Click the [Close] button. 11. Open the device manager again and check that the USB driver has been installed. 12. Check that “Sony Digital Wireless Transmitter (COM number) is displayed under the port (COM and LPT).
  • Page 70 In the case of Windows 8/8.1 1. Connect this unit and PC with the USB cable. 2. Click [Settings] on the start screen. 3. Click [Change PC settings]. 5-22 (E) DWT-B30...
  • Page 71 4. In the case of Windows 8.0 Select [General], and then click the [Restart|now] button in [Advanced startup]. In the case of Windows 8.1 Select [Recovery] in [Update and recovery], and then click the [Restart|now] button in [Advanced startup]. 5-23 (E) DWT-B30...
  • Page 72 5. Restart this unit. 6. Click [Troubleshoot]. 7. Click [Advanced options]. 8. Click [Startup Settings]. 5-24 (E) DWT-B30...
  • Page 73 9. Click the [Restart] button. 10. Restart this unit. 11. Select [7) Disable driver signature enforcement]. 12. Open the control panel from the desk top, and the click [Device Manager]. 5-25 (E) DWT-B30...
  • Page 74 13. Right-click [Unknown device], and then select [Update Driver Software...]. 14. Click [Browse my computer for driver software]. 15. Click the [Browse...] button. 5-26 (E) DWT-B30...
  • Page 75 16. Select C:\Program Files(*)\Sony\DWT-B30 Version <X.XX> Updater, and then click the [OK] button. (*): In the case of 64bit OS, Program Files x86 17. Click the [Next] button. 18. Click [Install this driver software anyway]. 5-27 (E) DWT-B30...
  • Page 76 19. Check that the following screen is displayed. (The installation has been completed.) (The screen shows the case when the transmitter and PC are connected by USB connection.) 20. Click the [Close] button. 21. Restart PC. 5-28 (E) DWT-B30...

  • Page 77: Firmware Update

    2. Turn on the power of this unit. 3. Connect this unit and PC with the USB cable. 4. Start DWT-B30 Version Updater. Click [All Programs] → [Sony DWL Flash Write Tool] → [DWT-B30Version X.XX Updater] from the start menu. (X.XXX indicates the version number.) 5-29 (E)
  • Page 78 Click the [OK] button. (The following screen shows the case that the version was updated to 1.03.) 6. Click the [Exit] button to quit DWT-B30 Version Updater. 7. Turn off the power of this unit and disconnect the USB cable.
  • Page 79 4. When the update is completed, a message indicating that the update has been completed normally is displayed. Click the [OK] button. (The following screen shows the case that the version was updated to 1.10.) 5. Click the [Exit] button and quit the update tool. 5-31 (E) DWT-B30...
  • Page 80 Version check of update tool 1. Click [Help] → [GUI Version]. 2. The version of this software is displayed. 5-32 (E) DWT-B30...

  • Page 81: Writing Of Serial Number

    The serial number is indicated on the model name plate. When writing the serial number, “DWL Flash Write” is required. It is different from the update software “DWT-B30 Flash Write” for the firmware update. Procedure 1. Remove the lid (USB). (Refer to Section 3-2-3.) 2.

  • Page 82: Version Check Procedure

    For details on the menu, refer to the Operating Instructions of this unit. Version check procedure of CPU, FPGA and REMOTE Enter the test mode (refer to Section 1-5) and check the following versions. . CPU VERSION . FPGA VERSION . REMOTE VERSION 5-34 (E) DWT-B30...

  • Page 83: Spare Parts

    Therefore, specified parts should be used in the case of な部品です。したがって，交換する時は必ず指定 replacement. の部品を使ってください。 2. Standardization of Parts 2.  部品の共通化 Some repair parts supplied by Sony differ from those   ソニーから供給する補修用部品は，セットに使われて used for the unit. These are because of parts common- いるものと異なることがあります。 ality and improvement.

  • Page 84: Exploded Views

    Case (Lower) and Boards 6-2. Exploded Views (b) (c) To CN-4088 board To LED-498 board P1.7 DWT-B30...
  • Page 85 3-700-671-01 s KNOB (SW) 3-700-678-01 s LID (USB) 4-109-127-02 s SCREW,+PSW M1.7 4-993-496-01 s SCREW (1.7X3.5), +PSW 5-001-828-01 s HOLDER, EL 5-001-833-01 s SHEET, DETECTION 5-001-834-01 s SHEET, BLINDFOLD (EL) 5-013-725-01 s PROTECTION SHEET, POWER SW 7-627-552-18 s SCREW,PRECISION +P 1.7X1.6 DWT-B30...

  • Page 86: Case (Upper) And Connectors

    Case (Upper) and Connectors For H (CE), L (CE) For CN, UC, G (J), MH (J), L (J) To DPR-396 board To TX-172 board (b) (c) DWT-B30...
  • Page 87 (For G(J), L(J), MH(J), UC, CN) 4-429-352-01 s WASHER (B) (For G(J), L(J), MH(J), UC, CN) 4-429-515-01 s SHEET, PROTECTION 4-993-496-01 s SCREW (1.7X3.5), +PSW 5-001-829-01 s WINDOW (EL) 5-001-830-01 s CUSHION (EL) 5-001-833-01 s SHEET, DETECTION 5-002-975-01 s CUSHION(O) DWT-B30...

  • Page 88: Packing Materials & Supplied Accessories

    *1 4-736-207-01 s LABEL (1.2G/L/MH/B), DISCERN 1pc *2 5-014-889-01 s CD-ROM (INSTRUCTION MANUAL) (ENGLISH, FRENCH, GERMAN, ITALIAN, SPANISH) 1pc *1 5-014-894-01 s CD-ROM (INSTRUCTION MANUAL) (JAPANESE) 1pc *3 5-014-898-01 s CD-ROM (INSTRUCTION MANUAL) (SIMPLIFIED CHINESE) 7pcs 7-627-556-08 s SCREW +P 2.6X2.8 DWT-B30...

  • Page 89: Diagrams

    IC808 receives frequency setting data from CPU (IC402 on the DPR-396 board) and controls the oscilla- tion frequency of a carrier, which VCO802 outputs, with the oscillation frequency of X801 as standard. Orthogonal modulation circuit (IC802’s peripheral circuit) IC802 modulates the I/Q signal, input from FPGA, to the carrier input from VCO802. 7-1 (E) DWT-B30...

  • Page 90: Dpr-396 Board

    The bandwidth of 2.4 GHz is used for the transmit frequency. IC2000 is CPU and IC2001 is the transceiver. The transmission output-adjusted value and remote-control ID are memorized by the internal EEPROM of IC2000. 7-2 (E) DWT-B30...

  • Page 91: Pin Description Of Cpu (Ic402 On The Dpr-396 Board)

    TX_POW_H/L RF POWER SELECT PC6/A14/OC3A PLL_LD PLL LOCK DETECT PC7/A15/IC3/CLK0 SLEEPS/P_G S/P IC ENABLE PE2/ALE/HWB FLASH_CS FPGA FLASH ROM CHIP SELECT PA7/AD7 CS_B DECORDER C PIN CHIP SELECT PA6/AD6 OEL_D/C OLED DATA/COMMAND SELECT PA5/AD5 OEL_RES OLED RESET 7-3 (E) DWT-B30...
  • Page 92 TEST DATA OUTPUT FOR JTAG PF5/ADC5/TMS TEST MODE SELECT FOR JTAG PF4/ADC4/TCK TEST CLOCK FOR JTAG PF3/ADC3 PF2/ADC2 MODEL_DETECT MODEL DETECT PF1/ADC1 TEMP TEMPERATURE MONITOR PF0/ADC0 BATT BATT VOLTAGE MONITOR AREF AREF A/D REFERENCE VOLTAGE GND3 AGND AVCC AVCC EPAD EPAD 7-4 (E) DWT-B30...

  • Page 93: Block Diagrams

    2.5V FLASH SPI1 SPI1 SPI2 Shift X'tal Register 12.288MHz IC201 IC300 FPGA SHDN IC500 CN-4148 Internal SG IQDAC Encode Packet RATE DATA DATA DATA CN500 CN4012 CN, UC, G (J), MH (J), L (J) IC504 IC570 PH501-PH503 CN4012 Overall DWT-B30...

  • Page 94: Frame Wiring

    CN-4078 (For H (CE), L (CE)) CN-4148 (For CN, UC, G (J), MH (J), L (J)) CN002 CN4002 CN4012 CN500 CN4001 AF CONNECTOR RM-215 CN2002 CL4001-CL4004 CN2001 CN401 CN600 BATT TERMINAL 3.0V ASSEMBLY CN405 AA SIZE BATT 2 Micro B Frame Wiring DWT-B30...

  • Page 95: Revision History

    Revision History Date History Contents 2019. 12 1st Edition ― 9-932-731-01 DWT-B30...
  • Page 97 商標について このマニュアルに記載されている商標および登録商標は下記のとおりです。 .  Windows は，米国 Microsoft Corporation 社の米国およびその他の国における登録 商標または商標です。 その他，記載されているシステム名，製品名は，一般に各開発メーカーの登録商標 あるいは商標です。 Trademarks Trademarks and registered trademarks used in this manual are as follows. .  Windows is a registered trademark of Microsoft Corporation in the United States  and Other countries. Other system names, product names, and company names appearing in this manual  are trademarks or registered trademarks of their respective holders. DWT-B30...
  • Page 98 DWT-B30 (CE) DWT-B30 (CN) DWT-B30 (J) Printed in Japan Sony Corporation DWT-B30 (UC) J, E 2019. 12 08 9-932-731-01 ©2019...

Table of Contents