Oriental motor 2TK3GN-AW2J Operating Manual

O P E R A T I N G „ M A N U A L
Torque„Motors
Introduction
„ „ Before„using„the„motor
Only qualified personnel of electrical and mechanical engineering should work
with the product.
Use the product correctly after thoroughly reading the section "Safety precautions."
In addition, be sure to observe the contents described in warning, caution, and
note in this manual.
The product described in this manual has been designed and manufactured to be
incorporated in general industrial equipment. Do not use for any other purpose.
Oriental Motor Co., Ltd. is not responsible for any damage caused through failure
to observe this warning.
If you have purchased a torque motor and power controller package, also refer to
the operating manual for TM Series.
„ „ Standard„and„CE„Marking
Motors described in this manual are recognized by UL under the UL and CSA
standards, and conform to the China Compulsory Certification System (CCC
System). The motors are also affixed the CE Marking under the Low Voltage
Directive.
Model names, which conform to the standards, are the motor model names.
Standards
UL 1004-1, UL 1004-3, CSA C22.2 No.100, CSA C22.2 No.77, GB/T 12350
Standards File No.
UL File No.E64197, CQC
Applications for Standard
EN 60034-1, EN 60034-5, EN 60664-1, EN 60950-1
A Running Heating Test and a Locked-Rotor Test has been conducted with a
aluminum radiation plate of size indicated below. For the motor with a gearhead,
tests has been conducted with a gearhead instead of the radiation plate.
First number in
Size [mm (in.)]
motor name
2 115 × 115 (4.53 × 4.53)
3 125 × 125 (4.92 × 4.92)
4 135 × 135 (5.31 × 5.31)
5 165 × 165 (6.50 × 6.50)

Installation conditions

Overvoltage category II, Pollution degree 2, Class I equipment (For EN Standards)
When the machinery to which the motor is mounted requires overvoltage category
III and pollution degree 3 specifications, install the motor in a cabinet that comply
with IP54 and connect to power supply via an isolation transformer.
Standards for accessories
Capacitor: UL File No.E83671 (CYWT2),
VDE License Nos.112847 (capacitors with a rated voltage of 250 VAC),
114747 (capacitors with a rated voltage of 450 VAC)
Capacitor cap: UL File No.E56078 (YDTU2)
„ „ RoHS„Directive
The products do not contain the substances exceeding the restriction values of
RoHS Directive (2011/65/EU).
HM-9208-6
Thickness
Material
[mm (in.)]
5 (0.20) Aluminum
Thank you for purchasing an Oriental Motor product.
This Operating Manual describes product handling procedures and safety
precautions.
• Please read it thoroughly to ensure safe operation.
• Always keep the manual where it is readily available.
Safety„precautions
The precautions described below are intended to prevent danger or injury to the
user and other personnel through safe, correct use of the product. Use the product
only after carefully reading and fully understanding these instructions.
Handling the product without observing the instructions
Warning
that accompany a "Warning" symbol may result in
serious injury or death.
Handling the product without observing the instructions
Caution
that accompany a "Caution" symbol may result in injury
or property damage.
The items under this heading contain important handling
Note
instructions that the user should observe to ensure safe
use of the product.
• Do not use the product in explosive or corrosive environments, in the
presence of flammable gases, locations subjected to splashing water, or near
combustibles. Doing so may result in fire, electric shock or injury.
• Assign qualified personnel the task of installing, wiring, operating/controlling,
inspecting and troubleshooting the product. Failure to do so may result in fire,
electric shock or injury.
• Do not transport, install the product, perform connections or inspections when
the power is on. Always turn the power off before carrying out these operations.
Failure to do so may result in electric shock.
• Turn off the power in the event the overheat protection device (thermal
protector) is triggered. Failure to do so may result in injury or damage to
equipment, since the motor will start abruptly when the overheat protection
device (thermal protector) is automatically reset.
• The motor is Class I equipment. Install the motor so as to avoid contact with
hands, or ground it to prevent the risk of electric shock.
• Install the motor in an enclosure in order to prevent electric shock or injury.
• Keep the input-power voltage within the specification to avoid fire and electric
shock.
• Connect the cables securely according to the wiring diagram in order to prevent
fire and electric shock.
• Do not forcibly bend, pull or pinch the lead wires. Doing so may result in fire
and electric shock.
• Be sure to insulate the connection terminal of the capacitor. Failure to do so may
result in electric shock.
• Turn off the power in the event of a power failure, or the motor will suddenly
start when the power is restored and may cause injury or damage to equipment.
• Do not touch the connection terminal of the capacitor immediately after the
power is turned off (for a period of 30 seconds). The residual voltage may cause
electric shock.
• Do not disassemble or modify the motor. This may cause electric shock or injury.
• Do not use the motor beyond its specifications, or electric shock, injury or
damage to equipment may result.
• Do not touch the motor during operation or immediately after stopping. The
surface is hot and may cause a skin burn(s).
• Do not hold the motor output shaft or motor lead wires. This may cause injury.
• Keep the area around the motor free of combustible materials in order to prevent
fire or a skin burn(s).
• To prevent the risk of damage to equipment, leave nothing around the motor that
would obstruct ventilation.
• To prevent bodily injury, do not touch the rotating parts (output shaft) of the
motor during operation.
• Immediately when trouble has occurred, stop running and turn off the power.
Failure to do so may result in fire, electric shock or injury.
Warning
Caution
1