WARNING Disconnect from the mains electricity supply before attempting any maintenance or adjustment.
FAULT
LINE NOT FEEDING
OR
LINE TOO SHORT
OR
TRIMMER VIBRATES
CONTINUOUS
CLATTERING NOISE
LINE SNAPS
CONTINUOUSLY
IF NONE OF THE ABOVE
OR IF FAULT PERSISTS
N1 - Manual line feed button
To manually feed the nylon line (N)
1. If required line can be fed out manually.
2. To operate, press and release manual line feed
button, whilst gently pulling on one of the lines
until the line reaches the line cutter.
3. When the required amount of line is fed out,
gently pull on the second line (there is no need
to press the manual line feed button again).
P1 - Cap, P2 - Cap Release Latch, P3 - Spool,
P4 - Spoolholder, P5 - Slot,
Q1 - Upper Section, Q2 - Lower Section
To remove spool cap
1. Press and hold in the two cap release latches.
(P).
2. Pull cap away from the spoolholder. (P).
When refitting the spool cap
1. Keep all areas of the cap and spoolholder clean.
Failure to do so may prevent the cap being
securely located in the spoolholder.
2. Replace the cap, pressing firmly DOWN towards
the spoolholder to ensure cap is fully located.
3. Check that the cap is correctly fitted by trying to
remove it without depressing the two latches.
To replace nylon line.
For your convenience it is recommended you buy
spool and line complete. Nylon line only is also
available. Both are available from Electrolux
Outdoor Products stockists.
•
If you have spool and line complete, follow steps
5 to 11.
•
If you have nylon line only, follow the full
procedure below.
•
IMPORTANT: Always wind the line onto the
upper section of the spool first.
ENGLISH - 3
FAULT FINDING CHART
CHECK
Is the automatic line feed
working?
Are both lines fed out and visible?
Is the manual line feed working?
Has the motor reached full speed
before use?
Has too much line been fed out?
Is the line cutter missing from the
safety guard?
Are you using the trimmer
correctly?
Is the line jamming on the spool?
Contact Electrolux Outdoor Products Customer Service
Telephone : 01325 300303
MANUAL LINE FEED
SPOOL CAP AND NYLON LINE
Manually feed out line.
No
SEE "MANUAL LINE FEED"
Remove cap and spool, free line and
No
re-fit spool and cap. SEE "SPOOL
CAP AND NYLON LINE"
The line may be jammed on the
spool. Rewind line to remove
No
crossed loops. Check that line is in
correct section of spool.
Allow the motor to reach full speed
No
before use
Yes
SEE "MANUAL LINE FEED"
Contact your local approved
Service Centre or Electrolux
Yes
Outdoor Products Customer
Service.
Only use tip of nylon line to trim.
?
SEE "How to trim and edge"
Rewind the line on the spool, if symptoms
Yes
still persist, change spool and line.
4. If the line extends past the line cutter, too much
line has been fed out.
5. If too much line is fed out, remove the spool cap
and click spool anti-clockwise until the line is at
the desired length.
•
Remember ! Your Flymo Trimmer is designed
to use only nylon line with a maximum
diameter of 1.5mm. Use only genuine Flymo
nylon line.
1. Take approximately 5 metres of line. Insert
15mm of line into one of the holes in the upper
section of the spool (Q) and wind line in the
direction of the arrows on the top of the spool.
2. Leave approximately 100mm of line unwound
and place into cleat as illustrated in figure R.
3. Repeat on lower section of spool.
4. Care should be taken to ensure that the line is
neatly coiled on the spool. Failure to do so will
impair the efficiency of the automatic line feed.
5. Remove the cap.
6. Remove the old spool.
7. Place spool into spoolholder.
8. Release one line from cleat.
9. Secure line into slot (P).
10. Repeat for second line.
•
Ensure spool is fully located by gently
rotating it during fitment, whilst keeping the
spoolholder steady.
11. Refit the cap.
ACTION