Table of Contents
Advertisement
WARNING Disconnect from the mains electricity supply before attempting any maintenance or adjustment.
FAULT
LINE NOT FEEDING
OR
LINE TOO SHORT
OR
TRIMMER VIBRATES
CONTINUOUS
CLATTERING NOISE
LINE SNAPS
CONTINUOUSLY
IF NONE OF THE ABOVE
OR IF FAULT PERSISTS
To manually feed the nylon line (R)
Please note: Depending on which model you have
purchased, your trimmer may be fitted with one line
or two lines.
R1-a - Manual Line Feed Button
R2-a - Manual Line Feed Button
1. If required line can be fed out manually.
2. To operate, press and release manual line feed
button, whilst gently pulling on the line until it
S1-a - Cap Release Latches, S2-a - Cap,
S2-b - Spool, S2-c - Spoolholder, S2-d - Eyelet,
S2-e - Manual Line Feed Button, S3-a - Eyelet,
S4-a - Hole in Spool, S4-b - Line
To remove spool cap
1. Press and hold in the two cap release latches. See
fig S1.
2. Pull cap away from the spoolholder. See fig S2.
When refitting the spool cap
1. Keep all areas of the cap and spoolholder clean.
Failure to do so may prevent the cap being securely
located in the spoolholder.
2. Align the two latches on the cap with the two
windows in the spoolholder, then press down into
the locked position.
3. Ensure the two cap release latches are clearly visible and
are fully engaged with the windows in the spoolholder.
4. Check that the cap is correctly fitted by trying to
remove it without depressing the two latches.
To replace nylon line. Replacement nylon line is
available from most Electrolux Outdoor Products
stockists. You can buy it either as spool and line
complete, or as nylon line only.
FAULT FINDING CHART
CHECK
Is the automatic line feed
working?
Is line fed out and visible? (Check
for both lines if 2 lines are fitted)
Is the manual line feed working?
Has the motor reached full speed
before use?
Has too much line been fed out?
Is the line cutter missing from the
safety guard?
Are you using the trimmer
correctly?
Is the line jamming on the spool?
Contact Electrolux Outdoor Products Customer Service
Telephone : 01325 300303
MANUAL LINE FEED
SPOOL CAP AND NYLON LINE (1 LINE) - S
Manually feed out line.
No
SEE "MANUAL LINE FEED"
Remove cap and spool, free line and
re-fit spool and cap.
No
SEE "SPOOL CAP AND NYLON
LINE"
The line may be jammed on the spool.
Rewind line to remove crossed loops.
No
(Check that line is in correct section of
spool if 2 lines are fitted)
Allow the motor to reach full speed
No
before use
Yes
SEE "MANUAL LINE FEED"
Contact your local approved
Service Centre or Electrolux
Yes
Outdoor Products Customer
Service.
Only use tip of nylon line to trim.
?
SEE "How to trim and edge"
Rewind the line on the spool, if symptoms
Yes
still persist, change spool and line.
reaches the line cutter. (If 2 lines are fitted do this to
one line only, then gently pull on the second line,
there is no need to press the manual line feed
button again).
3. If the line extends past the line cutter, too much line
has been fed out.
4. If too much line is fed out, remove the spool cap
and click spool anti-clockwise until the line is at the
desired length.
To replace spool and line (complete)
1. Unwind approximately 100mm of line and feed this
through eyelet, see fig S3, then drop the spool into
spoolholder smooth side uppermost.
To replace nylon line on spool.
1. Take line and insert into hole in spool.
2. Turn spool clockwise to wind on required amount of
line, (approx. half = 10m) and cut line to length, see
fig S4. Care should be taken to ensure that the line
is neatly coiled on the spool. Failure to do so will
impair the efficiency of the automatic line feed.
3. Leave approximately 100mm of line unwound and
feed this through eyelet, see fig S3, then drop the
spool into the spoolholder smooth side
uppermost.
•
Ensure spool is fully located by gently rotating it
during fitment.
•
Remember ! Your Flymo Multi-Trim is designed
to use only nylon line with a maximum diameter
of 1.5mm. Use only genuine Flymo nylon line.
ACTION
ENGLISH - 3
Advertisement
Table of Contents
