Related Manuals for Zodiac MS FILTER D470
Summary of Contents for Zodiac MS FILTER D470
- Page 1 Instructions for installation and use - English Filter Translation of the original instructions in French More documents on: www.zodiac-poolcare.com H0648400_REVB - 2018/09...
- Page 2 • Do not spray insecticide or any other chemical (inflammable or non-inflammable) in the direction of the appliance, as this may damage the body and cause a fire. • Zodiac® heat pump, filter pump and filter appliances are compatible with the most commonly used types of pool water treatment systems.
-
Page 3: Table Of Contents
The distribution or modification of this document in any way is prohibited, without prior • authorisation from Zodiac®. Zodiac® is constantly developing its products to improve their quality. The information • contained herein may therefore be modified without notice. CONTENTS ❶... -
Page 4: I Description
1" 1/2 2" 2" Weight Maximum filtration rate 50 m³/h/m² Working pressure 0.5 - 1.4 bar (7 - 20 psi) Test pressure 2.5 bar (36 psi) Operating temperature range (water) 2 °C - 40 °C * Zodiac® Crystal Clear glass granulometry... -
Page 5: I Dimensions And Marking
1.3 I Dimensions and marking : Air bleed screw (on the back of the pressure gauge) : Pressure gauge : Cover + seal : Diffuser : Multiway valve : Manifold : Strainers : Drain plug : Base : Tank : Automatic air release Dimension in mm D470 D530 D650 D800 D950 Clearance below valve... -
Page 6: ❷ Installation
❷ Installation 2.1 I Selecting the location • The filter must be installed: - after the circulation pump (see image - before the heating and/or water treatment system (see image - ideally 0.5 metres below the water level (see image - ideally less than 5 metres from the pool (see image - in a dry ventilated equipment room protected against frost. -
Page 7: I Assembling The Filter
2.2 I Assembling the filter 2.2.1 Assembling the pressure gauge and air release • Only tighten parts by hand. • Screw the T-connector provided ( ) into the central orifice ( ) of the translucent cap. Use the gasket provided ) to seal. - Page 8 2.2.2 Installing the multiway valve • Insert the gasket ( ) into the threaded orifice marked "TOP" of the multiway valve. Pass a nut ( ) around the short pipe ( ), then tighten the pipe firmly on the multiway valve to ensure sealing (see image •...
- Page 9 2.2.3 Filling the filter • Remove the bolts and washers holding the translucent cover shroud. Set aside. • Remove the shroud, the cover and its seal. Set aside. • Check that the diffuser, the manifold and its strainers are in good position and correctly positioned. •...
-
Page 10: ❸ Use
❸ Use 3.1 I Operating principle The filter is essential for a swimming pool since it contributes to water treatment and ensures its clarity. Water passes through the filter media in the filter vessel and impurities are removed. The greater the accumulation of impurities, the more the pressure in the filter will increase. Identify the normal operating pressure on the pressure gauge when turning on. - Page 11 Position "Waste" This is carried out to drain the pool or lower the water level. The water is sent directly to the evacuation without going through the filter. • In this case, and if the pool has a bottom plug hole, aspirate the water through the bottom plug hole only to prevent air from getting into the pipes.
-
Page 12: I Operation
3.3 I Operation • To prevent against any risk of explosion that may cause material damage, serious injury or even death, make sure that the hydraulic circuit is free of any debris or blockage and is not subject to excessive pressure, and that the filter cover is properly positioned and tightened. •... -
Page 13: ❹ Maintenance
❹ Maintenance 4.1 I Winterizing • Stop the water circulation. • Clean the filter (see §4.1.2 Backflushing). • Drain the water out of the filter (see §4.1.3 Replacing the filter media), and the entire hydraulic circuit. • If the filter is positioned below the water level, close the isolation valves at suction and discharge. •... -
Page 14: ❺ Troubleshooting
❺ Troubleshooting • If a problem occurs, before you contact your retailer, please carry out these few simple checks using the following tables. • If the problem continues, contact your retailer. • : Actions to be performed by a qualified technician only Malfunction Possible causes Solutions... - Page 16 Your retailer Modèle appareil Appliance model Numéro de série Serial number Pour plus d’informations, enregistrement produit et support client : For more information, product registration and customer support: www.zodiac.com ZODIAC® is a registered trademark of Zodiac International, S.A.S.U., used under license.