TAKATA MIDI I-SIZE PLUS Instructions Manual page 28

40-105 cm
Hide thumbs Also See for MIDI I-SIZE PLUS:
Table of Contents

Advertisement

Available languages
  • EN

Available languages

  • ENGLISH, page 20
the TAKATA I-SIZE BASE (PLUS). It is properly
locked in place when you can see a green marking on
the top of each rear hook's release element and if you
checked prior to installation of the TAKATA MIDI
I-SIZE (PLUS) on the TAKATA I-SIZE BASE (PLUS)
that the rear connection hooks were open
[MIDI_I-SIZE_PLUS_040].
NOTE!
[MIDI_I-SIZE_PLUS_043] Check the TAKATA MIDI
I-SIZE (PLUS) is correctly secured to the TAKATA
I-SIZE BASE (PLUS), by gently shaking the seat in
each direction. If the seat is not properly secured to the
base, repeat Step 2 – Lock the seat into the TAKATA
I-SIZE BASE (PLUS) until it is in the correct
position.
Securing the TAKATA MIDI I-SIZE (PLUS) in a
forward-facing position [MIDI_I-SIZE_PLUS_044]
Step 1 – Check the TAKATA I-SIZE BASE (PLUS)
WARNING!
The TAKATA MIDI I-SIZE (PLUS) must only be
secured via the TAKATA I-SIZE BASE (PLUS). As
such, ensure that the TAKATA I-SIZE BASE (PLUS)
is attached fi rmly and correctly to the vehicle seat. If
you notice that the TAKATA I-SIZE BASE (PLUS)
can still be moved around, repeat all the steps in
Section 4 – Use in the vehicle (Securing the TAKATA
I-SIZE BASE (PLUS)).
WARNING!
[MIDI_I-SIZE_PLUS_040] Before installing the
TAKATA MIDI I-SIZE (PLUS) on the TAKATA
I-SIZE BASE (PLUS), check that both rear connec-
tion hooks of the TAKATA I-SIZE BASE (PLUS) are
open. The connection hooks have been correctly
unlocked if you can see a red marking on the top of
each release element.
In case of unclear colour or in diffi cult light conditions
push down one of the release elements on the exterior
of the connection arms to ensure that both connection
hooks are open.
Step 2 – Lock the seat into the TAKATA I-SIZE BASE
(PLUS)
[MIDI_I-SIZE_PLUS_045] Turn the TAKATA MIDI
I-SIZE (PLUS) so that it faces the direction of travel,
and place it above the middle of the TAKATA I-SIZE
BASE (PLUS). Press the two connection bolts in the
seat area of the TAKATA MIDI I-SIZE (PLUS) into
the rear connection hooks of the TAKATA I-SIZE
BASE (PLUS). For guidance, use the arrows on the
outside of the seat and on the rear connection arms of
the TAKATA I-SIZE BASE (PLUS). The bolts are
properly locked into the rear connection hooks when
each one clicks into place, and you can see a green
marking on the top of each hook's release element.
[MIDI_I-SIZE_PLUS_046] To secure the connection
rod in the foot area of the TAKATA MIDI I-SIZE
(PLUS) with the front connection hooks of the
TAKATA I-SIZE BASE (PLUS), press down from
above on the seat section of the TAKATA MIDI
I-SIZE (PLUS), until you hear a click.
WARNING!
[MIDI_I-SIZE_PLUS_046] Do not use the TAKATA
MIDI I-SIZE (PLUS) if it is not correctly secured to
the TAKATA I-SIZE BASE (PLUS). It is properly
locked in place when you can see a green marking on
the top of each rear hook's release element and if you
checked prior to installation of the TAKATA MIDI
I-SIZE (PLUS) on the TAKATA I-SIZE BASE (PLUS)
that the rear connection hooks were open
[MIDI_I-SIZE_PLUS_040].
NOTE!
[MIDI_I-SIZE_PLUS_043] Check the TAKATA MIDI
I-SIZE (PLUS) is correctly secured to the TAKATA
I-SIZE BASE (PLUS), by gently shaking the seat in
each direction. If the seat is not properly secured to the
base, repeat Step 2 – Lock the seat into the TAKATA
I-SIZE BASE (PLUS) until it is in the correct
position.
Removing the TAKATA MIDI I-SIZE (PLUS)
from the TAKATA I-SIZE BASE (PLUS)
Step 1 – Release the rear connection hooks
[MIDI_I-SIZE_PLUS_031] The rear hooks unlock
together, so you only need to push down one of the
release elements on the TAKATA I-SIZE BASE
(PLUS) rear connection arms. At the same time, tilt
the TAKATA MIDI I-SIZE (PLUS) forward (in the
direction of travel), so that the connection bolts of the
seat come out of the rear connection hooks of the base.
Step 2 – Free the seat from the front connection hooks
and remove
[MIDI_I-SIZE_PLUS_047] Free the connection rod of
the TAKATA MIDI I-SIZE (PLUS) from the front
hooks of the TAKATA I-SIZE BASE (PLUS) by
sliding the TAKATA MIDI I-SIZE (PLUS) backward,
against the direction of travel. You should now be able
to lift the TAKATA MIDI I-SIZE (PLUS) from the
de
en
en
fr
it
es
pt
nl
25

Advertisement

Table of Contents
loading

Table of Contents