TAKATA MIDI I-SIZE PLUS Instructions Manual page 25

I-SIZE (PLUS) can be adjusted by pressing the seat
inclination lever below the front end of the shell
upwards. Keep the seat inclination lever pressed, and
at the same time, pivot the shell up or down at the
front end. Then release the seat inclination lever again
so that the seat shell is locked in upper or lower
position. This is indicated by a click.
CAUTION!
Whenever you adjust the seat inclination, check that
the seat shell and lever are locked into position again.
To do this, gently try to move the front end of the shell
up or down, without pressing the inclination lever.
NOTE!
The inclination of the seat can only be adjusted when
installing the TAKATA MIDI I-SIZE (PLUS) forward
facing on the TAKATA I-SIZE BASE (PLUS).
If it is not possible to install the TAKATA MIDI
I-SIZE (PLUS) rearward facing on the TAKATA
I-SIZE BASE (PLUS), please kindly check the
position of the inclination. If necessary, change the
inclination and install the TAKATA MIDI I-SIZE
(PLUS) rearward facing on the TAKATA I-SIZE
BASE (PLUS) again.
TAKATA I-SIZE BASE (PLUS)
Adjusting the support leg
Step 1 – Fold out the support leg
[MIDI_I-SIZE_PLUS_025 + MIDI_I-SIZE_PLUS_026]
Take hold of the support leg on the underside of the
TAKATA I-SIZE BASE (PLUS). Push the release
slider of the folding mechanism to the side, pull the
support leg out of the transportation position, and
swing it out as far as it will go. When it reaches full
extension, the support leg is locked into place by a
spring in the release slider.
Step 2 – Unlock and adjust the support leg
[MIDI_I-SIZE_PLUS_027] Press the button on the
height adjustment mechanism as far in as possible, and
slide the support leg up or down. When the desired
position is reached, release the button and check that
the support leg is locked in place. This is indicated by a
click, and a green marking on the top of the button.
WARNING!
If the support leg is not set at the correct height, there
is a risk of serious injury to the child or other
passengers in the case of an accident.
22
[MIDI_I-SIZE_PLUS_037] The correct position of
the support leg is set when the support leg of the
TAKATA I-SIZE BASE (PLUS) lies completely and
fl ush against the vehicle fl oor, and the indicator at the
lower end of the support leg is fully showing a green
marking.
Step 3 – Fold in and lock the support leg
[MIDI_I-SIZE_PLUS_025] To be able to fold in the
support leg, you must fi rst position it in the smallest
height setting. Push the release slider of the folding
mechanism to the side, and swing the support leg
towards the underside of the base. When the support
leg lies snug against the underside of the TAKATA
I-SIZE BASE (PLUS), the support leg is locked into
place by a spring in the release slider.
Adjusting the ISOFIX connectors
The two ISOFIX connectors on the TAKATA I-SIZE
BASE (PLUS) must be adjusted, according to the
position of the ISOFIX points in the vehicle. Each of
the connectors can independently be set to one of six
different lengths, with the various settings indicated by
fi gures 1 to 5 on the top of them. Setting six is obtained
when the connectors are at full extension, and is
indicated by the absence of any fi gure.
Step 1 – Unlock the ISOFIX length adjuster
[MIDI_I-SIZE_PLUS_028] Press the left-hand button
on the ISOFIX length adjuster as far in as possible and
hold it in position. The adjuster is positioned on the
inner side of the TAKATA I-SIZE BASE (PLUS).
Step 2 – Adjust the ISOFIX connector
At the same time, pull the left-hand ISOFIX connector,
positioned on the outside of the TAKATA I-SIZE
BASE (PLUS), into the required position.
Step 3 – Lock the ISOFIX length adjuster
Release the button and connector, and check whether
the latter is locked in place. This is indicated by a click,
and a green marking on the button.
NOTE!
The two ISOFIX connectors must be adjusted
independently. Repeat steps 1 to 3 for the right-hand
connector.
WARNING!
[MIDI_I-SIZE_PLUS_029] When securing the
TAKATA I-SIZE BASE (PLUS) in the vehicle, ensure
that both ISOFIX connectors are set to the same
position. To do this, check that the fi gures on the top