Inscape Data NVC 1000 Series User Manual

Network ptz color camera
Hide thumbs Also See for NVC 1000 Series:

Advertisement

Quick Links

NVC 1000/3000 User's Guide
NVC 1018 / 1026 / 3018 / 3026
Network PTZ Color Camera
NVC 1000 Series
NVC 1000 Series
NVC 1000 Series
NVC 1000 Series
Indoor Speed Dome
Network Camera
User's Guide
NVC 3000
NVC 3000
NVC 3000
NVC 3000
Outdoor Speed Dome
Network Camera
Rev1.0(Dec.2006)

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the NVC 1000 Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Inscape Data NVC 1000 Series

  • Page 1 NVC 1000/3000 User’s Guide NVC 1018 / 1026 / 3018 / 3026 Network PTZ Color Camera User’s Guide NVC 1000 Series NVC 1000 Series NVC 1000 Series NVC 1000 Series NVC 3000 NVC 3000 NVC 3000 NVC 3000 Indoor Speed Dome...
  • Page 2 NVC 1000/3000 User’s Guide Directions NVC 1000/3000 series network cameras are designed for outdoor/indoor use. Don’t use NVC 1000/3000 in an environment that exceeds the limited range. Be careful not to cause any physical damage by dropping or throwing the NVC 1000/3000 network camera. Especially keep the network camera out of reach from children.
  • Page 3 NVC 1000/3000 User’s Guide Warning & Caution for NVC 1000/3000 If you fail to read this information and handle the product incorrectly, death or serious injury may occur. The unit should be installed by trained personnel. Always stop using when the product emits smoke or abnormal heat.
  • Page 4: Table Of Contents

    NVC 1000/3000 User’s Guide Table of Contents 1. Introduction ......................... 6 1.1. Overview........................... 6 1.2. Features of NVC 1000/3000....................6 1.3. Applications of NVC 1000/3000..................9 2. Product Description ......................10 2.1. Package Contents ......................10 2.2. Preview........................... 10 2.3. PC Requirements ......................11 2.4.
  • Page 5 NVC 1000/3000 User’s Guide 6.3. Web Viewer)........................52 6.4. How to upgrade NVC 1000/3000 firmware................ 53 Appendix 1. On Site Installation of NVC 1018 / 1026 ............55 Appendix 2. On Site Installation of NVC 3018 / 3026 ............60 Rev.A.1 (Dec.2006)
  • Page 6: Introduction

    NVC 1000/3000 User’s Guide 1. Introduction 1.1. Overview The NVC 1000/3000 is a state-of-the-art Speed Dome network camera which transmits synchronized video and audio data in real time with D1 resolution at full frame rate. This is possible through MPEG4 CODEC technology, which provides high quality video with highly compressed data streams.
  • Page 7 NVC 1000/3000 User’s Guide Remote administration control Entire operational parameter set up, Software upgrade Various Mounting Brackets Wall, Pipe, Gooseneck mounting brackets Corner mount adaptor, Pole mount adaptor Built-in Fan / Heater Rev.A.1 (Dec.2006)
  • Page 8 NVC 1000/3000 User’s Guide Detailed Features of Speed Dome part World most silent speed dome camera Hot Keys Adoption of timing belt, specialized gear, and other low- This camera supports various hot key functions noise-technologies reduced mechanical vibration which for ease of control by other controllers or DVRs. significantly enhances durability and quality of the camera.
  • Page 9: Applications Of Nvc 1000/3000

    NVC 1000/3000 User’s Guide 1.3. Applications of NVC 1000/3000 IP surveillance (buildings, stores, manufacturing facilities, parking lots, banks, government facilities, military, etc., Real time Internet broadcasting Remote monitoring (hospitals, kindergartens, traffic, public areas, etc.,) Teleconference (Bi-directional audio conference) Remote Learning Weather and environmental observation Rev.A.1 (Dec.2006)
  • Page 10: Product Description

    NVC 1000/3000 User’s Guide 2. Product Description 2.1. Package Contents Open the package and check if you have the followings: NVC 1000 NVC 3000 1. Camera main body 1. All items of indoor speed dome 2. CD(Manual, S/W) network camera 3.
  • Page 11: Pc Requirements

    NVC 1000/3000 User’s Guide PC software to view and record the A/V PC software to allocate IP MPEG-4 Speed Dome Network Camera streaming data transmitted from NVC parameters to NVC 1000/3000 1000/3000 2.3. PC Requirements AV streaming data received from NVC 1000/3000 can be decoded or stored in a PC running NVR100 program which is a viewing &...
  • Page 12: Physical Description

    NVC 1000/3000 User’s Guide 2.4. Physical description 2.4.1 Bottom View and Connections Fig. 2-1 Bottom View of NVC 1000/3000 - Input/Output Connectors at Bottom panel of NVC 1000/3000 Connector Description Name 4 Alarm inputs(Signal pin number : 1, 2, 3, 4), 2 GND(ground) signals .
  • Page 13 . Connect 24 Volt AC adaptor to this terminal for supplying power to the network camera. AC adapter which is compliant to the specification for NVC 1000/3000 AC24V should be used. Misuse of power supply can cause damage to NVC 1000/3000. INSCAPE DATA assumes no responsibility for misuse of the power supply. Rev.A.1 (Dec.2006)
  • Page 14 NVC 1000/3000 User’s Guide 2.4.2 Dimension and basic parts of NVC 1000/3000 A. Dimension A-1. NVC 1000 Fig 2.2 Dimension of NVC 1000 (unit : mm) A-2. NVC 3000 Fig.2-3 Dimension of NVC 3000 Rev.A.1 (Dec.2006)
  • Page 15 NVC 1000/3000 User’s Guide B. Exterior and Interior of View B-1.Common part of NVC 1000/3000 Fig.2-5 Common part of NVC 1000/3000 Rev.A.1 (Dec.2006)
  • Page 16: Specification Of The Analog Camera

    NVC 1000/3000 User’s Guide B-2.Outdoor Housing of NVC 1000 Fig.2-6. Outdoor housing 2.5. Specification of the analog camera 2.5.1. Zoom cameras NVC 1000/3000 is offered with 2 types of zoom camera modules as described in the following table. Camera module Misc.
  • Page 17: Quick Installation Guide

    2.6. Quick Installation Guide Brief information for rapid installation is provided in this section. For more detailed information you are recommended to refer to pertinent documentations provided with the product or refer to Inscape Data’s home page (http://www.Inscape Data.com) 1. Apply power to NVC 1000/3000 and Connect NVC 1000/3000 to LAN like the following picture.
  • Page 18 NVC 1000/3000 User’s Guide administration mode can be found in [5. Configuring NVC 1000/3000 in Administrative Mode]. Among the parameters, the parameters in the following table should be set-up with proper values. Detailed information for the parameters in Administrator Mode is found in [5.
  • Page 19 NVC 1000/3000 User’s Guide Connecting Alarm Siren, Flashing Light, … annunciating device Connect NVC 1000/3000 to the network, Network connection Network LAN, ADSL or Cable modem. AC24V Supply AC power Apply AC24V power to network camera 6. Remote video connection to NVC 1000/3000 Run NVR100 on your PC.
  • Page 20: Connecting Nvc 1000/3000 To Ip Network

    NVC 1000/3000 User’s Guide 3. Connecting NVC 1000/3000 to IP Network NVC 1000/3000 supports LAN, xDSL, and Cable modem. It also supports shared IP environment where single IP address is shared by at least 2 IP devices. Refer to [IP-Installer User’s Guide] for details of setting the IP address for NVC 1000/3000.
  • Page 21: Connecting To Xdsl/Cable Modem

    NVC 1000/3000 User’s Guide units from within a local area network, you do not need to change the RTSP and HTTP port numbers, unless other IP sharing devices sit in-between the client and the IP video products. For more detailed information regarding the use of IP sharing device refer to the document [Use of Private IP network using IP-sharing- device].
  • Page 22 NVC 1000/3000 User’s Guide refer to the Application note regarding “Management Server” in the CD.) When connecting NVC 1000/3000 to xDSL or Cable modem, usually regular LAN cable is required. But since some modems have crossover connections, please contact your service provider for detailed information.
  • Page 23: Ip-Installer

    NVC 1000/3000 User’s Guide 4. IP-Installer NVC 1000/3000 needs IP network parameters for connection to the network(Internet/Intranet). IP-Installer is a PC program for the initial network configuration to IP video products such as Network Camera or A/V Server. IP- Installer is provided in a CD supplied with NVC 1000/3000 or it can be downloaded from “www.Inscape Data.com”.
  • Page 24: Configuring Nvc 1000/3000 In Administrative Mode

    NVC 1000/3000 User’s Guide 5. Configuring NVC 1000/3000 in Administrative Mode 5.1. Log On There are 2 ways of connecting to NVC 1000/3000 administrative mode. One is through Internet Explorer and the other is through “NVR100” program. 1. Using Internet Explorer Type in the connection address of the network camera in the address window of the Internet Explorer as followings: http://[NVC 1000/3000 IP address]/admin.htm...
  • Page 25 NVC 1000/3000 User’s Guide 3. Input User Name and Password in the display screen shown in Fig. 5-2. Fig. 5-2 Log On Screen Factory default User Name and Password are set as ‘root’ and ‘root’, respectively. Click on “OK” button to enter into the Basic Setup page of Administrative Mode.
  • Page 26: Basic Setup

    NVC 1000/3000 User’s Guide 5.2. Basic Setup Setup the basic parameters of the NVC 1000/3000. Fig. 5-3 Basic Setup Sub Field Field/Button Description /Button Language Select a language of your choice Logical name of the NVC 1000/3000. It is same as the one set-up by System Name IP-installer.
  • Page 27 NVC 1000/3000 User’s Guide Input Video This filed is set by the factory. Source Select a video size for transmission NTSC (30frames/sec Max.) : 176x144 / 352xNVC 3000 / Video Size 704x480. PAL/SECAM (25frames/sec Max.) : 176x144 / 352x288 / 704x576 Max upload Assign maximum bandwidth of the uplink for the network connected to...
  • Page 28: Network Configuration

    NVC 1000/3000 User’s Guide 5.3. Network Configuration Setup the network parameters appropriately in accordance with your network environment. Many of the parameters in this page are same as those set up by “IP-Installer”. Fig. 5-4 Network Configuration Rev.A.1 (Dec.2006)
  • Page 29 NVC 1000/3000 User’s Guide Sub Field Field/Button Description /Button The network types supported by the NVC 1000/3000 are LAN(fixed IP), PPPoE, and DHCP(automatic IP allocation) When the network environment is fixed IP, select ‘LAN’ in the network type, and put the IP address, Subnet Mask, Gateway, DNS1 and Static IP Setup DNS2.
  • Page 30 NVC 1000/3000 User’s Guide If you check this, the IP address will be sent via E-mail whenever the Notify for IP IP address changes. It is sent to the E-mail address set by “Recv E- Change Mail Address”. Recv E-Mail Enter E-mail address to receive information sent from your network Address camera.
  • Page 31: Wireless Configuration (This Is Not Applicable To Nvc 1000/3000 Network Camera)

    NVC 1000/3000 User’s Guide 5.4. Wireless Configuration Not applicable Rev.A.1 (Dec.2006)
  • Page 32: User Admin & Time Setup

    NVC 1000/3000 User’s Guide 5.5. User Admin & Time Setup You can change the ID and password of users and also assign different attributes for each user. Fig. 5-7 User Administrator & Time Setup Rev.A.1 (Dec.2006)
  • Page 33 NVC 1000/3000 User’s Guide Sub Field Field/Button Description /Button Administrator Admin ID. Default ID is “root” Username Administrator Admin password. The default password is “root”. password : Administrator Enter the password once more to confirm the password. Confirm Password Add User Enter the user ID you want to add.
  • Page 34 NVC 1000/3000 User’s Guide Fig. 5-8. User Authentication in NVC 1000/3000 If you uncheck for the Authentication for Viewing, all users can access If No, default the NVC 1000/3000 with the same attribute set here. Checked attributes attribute are enabled. Click “Save” to save the attribute. Current Time It shows you the current time of NVC 1000/3000.
  • Page 35: Sensor & Capture Setup

    NVC 1000/3000 User’s Guide 5.6. Sensor & Capture Setup This is the setup page for sensors and video capture conditions. Captured video can be sent to user by FTP or E- mail upon configuration. Fig. 5-9 Sensor & Capture Setup Sub Field Field/Button Description...
  • Page 36 NVC 1000/3000 User’s Guide Select Select a way of sending captured video. You can send captured video through FTP or E-mail, or both. Check to send captured video by e-mail. E-mail is sent to the Recv E-mail address. Refer to [Section 5.3.] By E-Mail Captured...
  • Page 37: Alarm Device Setup

    NVC 1000/3000 User’s Guide 5.7. Alarm Device Setup Test the alarm output and describe the condition of alarm annunciation. Sensor related alarm operation, alarm device can operate only when the sensor is active at least over 2 seconds. Fig. 5-10 Alarm Device Setup Sub Field Field/Button Description...
  • Page 38: Motion Region Setup

    NVC 1000/3000 User’s Guide SAVE Save the setup parameters. 5.8. Motion Region Setup Set the motion detection regions. Up to 3 regions can be defined. Fig. 5-11 Motion Region Setup Sub Field Field/Button Description /Button Not applicable. Channel Selection Channel Set the sensitivity in motion detection for each channel.
  • Page 39 NVC 1000/3000 User’s Guide Setup Enable each zone by checking the box at the left of each Region. . To set the region, 1. Click on START and click on a box overlaid on the video 2. Click on END and click on a box overlaid on the video. 3.
  • Page 40: Ptz Setup

    NVC 1000/3000 User’s Guide 5.9. PTZ Setup Fig. 5-12 PTZ Setup Sub Field Field/Button Description /Button Channel Not applicable Selection Choose the PTZ model. PTZ Model Selection Choose default model for proper operation. Delete Button Press this button to delete the setup of PTZ Your PTZ device needs an ID, input ID in this field.
  • Page 41 NVC 1000/3000 User’s Guide Panning Set the left/right limitation and test. Limitation Select Left/Right position before setting. Panning Clear the panning limitation previously set. Limitation The panning range will be the same as the PTZ device allows. RESET Panning Set the present position as left or right panning limitation. Limitation Panning Test the panning limitation which was set previously.
  • Page 42: Encryption Set Up

    NVC 1000/3000 User’s Guide 5.10. Encryption Set up Fig. 5-13 Encryption Setup For additional security to the video and audio data transmitted from the network camera, you can set key codes and use them for encrypting the data from the network camera. You can selectively activate encryption for the video and audio data.
  • Page 43 NVC 1000/3000 User’s Guide SAVE After the selection, click on SAVE button. You can use up to 20 different key codes for the encryption of the data To generate the key value click on “GENERATE” button. The boxes for GENERATE the Key values will be filled with new values.
  • Page 44: Upgrade & Reset

    You can upgrade the NVC 1000/3000 via IP network. Fig. 5-14 Upgrade & Reset For each of the upgrade of the system component, upgrade code should be downloaded from Inscape Data’s home page before the system upgrade is performed. (Refer to [6.4.
  • Page 45 [6.4. How to upgrade NVC 1000/3000 firmware] Add a new PTZ driver software via the network. PTZ driver can be Add PTZ File downloaded from Inscape Data’s home page. Refer to [6.4. How to upgrade NVC 1000/3000 firmware] Re-initialize the network camera to factory default state.
  • Page 46: Status Report

    NVC 1000/3000 User’s Guide 5.12. Status Report It shows you system records since the system started. Fig. 5-15 Status Report You can check the problems as well as the versions and event status of the whole system and each module. Rev.A.1 (Dec.2006)
  • Page 47: Tips For Using Nvc 1000/3000

    NVC 1000/3000 User’s Guide 6. Tips for Using NVC 1000/3000 6.1. Alarm (for Sensor input) and AUX(for Relay output) Alarm terminal at the connector panel of NVC 1000/3000 is used to connect various sensing and alerting devices. Examples of sensing devices are infrared sensors, motion sensors, heat/smoke sensors, magnetic sensor, etc. Aux terminal is used for connecting alerting device such as loud speaker, flashing light, etc.
  • Page 48 NVC 1000/3000 User’s Guide Please connect sensor between “Signal “and “GND” pin of the alarm terminal at the connector panel of NVC 1000/3000 Fig. 6-2 shows equivalent alarm input circuit of NVC 1000/3000. “+” and “-“are “Signal” and “GND”, respectively. Fig.
  • Page 49 NVC 1000/3000 User’s Guide Fig. 6-3 RELAY Output of NVC 1000/3000 3. Connection of Sensor, Alarm Device 3.1 Connection of Sensor (Fig.6-4) P ho to C o up l er N O /N C T yp e N O /N C T yp e O p en C o l l ecto rT yp e O p en C o l l ecto rT yp e N O /N C T yp e...
  • Page 50: Trouble Shooting

    NVC 1000/3000 User’s Guide R el ay S w i tch P o w er S upp l y A l arm A l arm A l arm A l arm 1V ~ 30 V D C /A C ,1 A 1V ~ 30 V D C /A C ,1 A 1V ~ 30 V D C /A C ,1 A 1V ~ 30 V D C /A C ,1 A...
  • Page 51 NVC 1000/3000 User’s Guide If you see the “Reply from …” message, it means that the server is properly connected. If you do not see a Reply message, check if the network cable and power cable are properly connected. 2. After successfully connecting he NVC 1000/3000 to IP network •...
  • Page 52: Web Viewer)

    NVC 1000/3000 User’s Guide 6.3. Web Viewer) NVC 1000/3000 is designed to be connected through internet explorer, too. For connection to NVC 1000/3000 using internet explorer type in IP address or host address in the address input field of the internet explorer. Fig.
  • Page 53: How To Upgrade Nvc 1000/3000 Firmware

    Followings are the procedure to apply for the manual upgrade 1) Save the upgrade system software to your PC. Upgrade software can be downloaded from Inscape Data’s home page or provided in CD.
  • Page 54 8) After rebooting, log on to the server in administrative mode again and click the “Status Report”. 9) Check the version number and release date of the NVC 1000/3000. You can download NVC 1000/3000 system software from Inscape Data’s homepage. http://www.Inscape Data.com...
  • Page 55: Appendix 1. On Site Installation Of Nvc 1018 / 1026

    NVC 1000/3000 User’s Guide Appendix 1. On Site Installation of NVC 1000 A. Preparations for the installation A-1. Open the Cover of the Dome Camera A-2. Set the DIP switches as in the following picture. When using system controller for the control of the dome, always set the RS-485 communication channel to be : NVC 30000 bps, 8 bit, 1 stop bit, no parity.
  • Page 56 NVC 1000/3000 User’s Guide A-3. Place the Dome Cover. B. Installation using Ceiling Mount Notice : Ceiling board should be strong enough to hold the weight of approx. 2kg. Rev.A.1 (Dec.2006)
  • Page 57 NVC 1000/3000 User’s Guide Rev.A.1 (Dec.2006)
  • Page 58 NVC 1000/3000 User’s Guide C. Installation using Embedded Mount Type Rev.A.1 (Dec.2006)
  • Page 59 NVC 1000/3000 User’s Guide Rev.A.1 (Dec.2006)
  • Page 60: Appendix 2. On Site Installation Of Nvc 3018 / 3026

    NVC 1000/3000 User’s Guide Appendix 2. On Site Installation of NVC 3000 A. Basic Components and Mounting Accessories A-1. Basic Components Rev.A.1 (Dec.2006)
  • Page 61 NVC 1000/3000 User’s Guide A-2. Mounting Accessories (Optional) Pipe Mount Bracket Pipe Mount Bracket Pipe Mount Bracket Pipe Mount Bracket Goose Neck Goose Neck Goose Neck Goose Neck Corner Mount Adapter Corner Mount Adapter Corner Mount Adapter Corner Mount Adapter Pipe Mount Adapter Pipe Mount Adapter Pipe Mount Adapter...
  • Page 62 NVC 1000/3000 User’s Guide B. Wall Mounting using Wall Mount Bracket The wall should be strong enough to hold 4 times of the weight of the camera (5.3 KG). This means that the wall should withstand weight of 21.2 KGs in the minimum. B-1.
  • Page 63 NVC 1000/3000 User’s Guide C. Pipe Mounting C-1. Preparations for the Mounting C-2. Cabling for the Pipe Mounting Rev.A.1 (Dec.2006)
  • Page 64 NVC 1000/3000 User’s Guide D. Gooseneck Mounting D-1. Preparations for the Mounting D-2. Cabling for the Gooseneck Mounting Rev.A.1 (Dec.2006)
  • Page 65 NVC 1000/3000 User’s Guide E. Corner Mounting E-1. Install a corner mount adaptor on the corner of wall. E-2. Use wall or gooseneck mount bracket to finish installation. F. Pole Mounting F-1. Install a pole mount adaptor on the pole. F-2.
  • Page 66 NVC 1000/3000 User’s Guide G. Fan & Heater H. Specifications and Dimension of Outdoor Housing H-1. Specifications Specification Description On: below 10 , Off: over 15 Heater control temperature On: over 45 , Off: below 35 Fan control temperature Operating temperature -40℃...
  • Page 67 NVC 1000/3000 User’s Guide H-2. Dimension of Outdoor Housing 1 9 0 .0 2 5 3 .0 U N IT S :m m Rev.A.1 (Dec.2006)
  • Page 68 NVC 1000/3000 User’s Guide SPECIFICATIONS NVC 1018 / 1026 NVC1018 NVC1026 Image Sensor 1/4" Sony Exview HAD CCD Total Image NTSC 811(H) * 508(V) 410K Pixels 795(H) * 596(V) 470K 768(H) * 494(V) 380K Number Of NTSC 752(H) * 582(V) 440K Effective Pixels Horizontal resolution More Than 480TV Lines...
  • Page 69 NVC 1000/3000 User’s Guide Operating System Microsoft Windows 2000 / XP System Processor CPU: Intel Pentium IV or equivalent Requirements Memory RAM: 512MB or more Browser Microsoft Internet Explorer Ver 5.0 or higher Construction Body(ABS), Anti-Vandal Dome(Poly Carbonate) Dimensions 5.8" (D) * 7.9"(H) / 147mm (D) * 2.03mm(H) Weight 1.9 kg (4.1 lbs) Environmental...
  • Page 70 NVC 1000/3000 User’s Guide SPECIFICATIONS NVC 3018 / 3026 NVC3018 NVC3026 Image Sensor 1/4" Sony Exview HAD CCD Total Image NTSC 811(H) * 508(V) 410K 795(H) * 596(V) 470K Pixels Number Of NTSC 768(H) * 494(V) 380K 752(H) * 582(V) 440K Effective Pixels Horizontal resolution More Than 480TV Lines...
  • Page 71 NVC 1000/3000 User’s Guide Operating System Microsoft Windows 2000 / XP System Processor CPU: Intel Pentium IV or equivalent Requirements Memory RAM: 512MB or more Browser Microsoft Internet Explorer Ver 5.0 or higher Construction Body(Aluminum), Anti-Vandal Dome (Poly Carbonate) Dimensions 9.9"(D) x 12"(H) x 7.5"(Bubble) / 253mm(D) x 307mm(H) x 190mm(Bubble) Weight 5.3kg (11.7 lbs), Dome only 3.4kg (7.5 lbs)

This manual is also suitable for:

Nvc 3000 seriesNvc 1018Nvc 1026Nvc 3018Nvc 3026

Table of Contents