Page 4
Foreword The installation, use and maintenance manual (hereinafter Manual) provides the user with information necessary for correct and safe use of the machine (or “appliance“). The following must not be considered a long and exacting list of warnings, but rather a set of instructions suitable for improving machine performance in every respect and, above all, preventing injury to persons and animals and damage to property due to improper operating procedures.
Contents WARNINGS AND SAFETY INFORMATION............................7 General information ................................... 7 Personal Protective Equipment ................................. 8 General safety ....................................8 Transport, handling and storage ................................ 9 Installation and assembly .................................. 9 Positioning ...................................... 10 Machine scrapping ..................................10 APPLIANCE AND MANUFACTURER’S IDENTIFICATION DATA ......................11 Data plate position ..................................
Page 6
Air duct connection ..................................21 Water drain connection ................................... 21 Electrical connection ..................................21 F.8.1 Power cable ................................... 21 F.8.2 Hood-oven interface cable ..............................22 COMMISSIONING AND SETTINGS ..............................23 Introduction ..................................... 23 Oven settings ....................................23 MACHINE SCRAPPING..................................24 Waste storage ....................................
A WARNINGS AND SAFETY INFORMATION General information To ensure safe use of the machine and a proper understanding of the manual it is necessary to be familiar with the terms and typographical conventions used in the documentation. The following symbols are used in the manual to indicate and identify the various types of hazards: WARNING Danger for the health and safety of operators.
Personal Protective Equipment Summary table of Personal Protective Equipment (PPE) to be used during the various stages of the machine's service life. Stage Protective Safety Gloves Glasses Safety garments footwear helmet — ● ○ — Transport — ● ○ — —...
• Do not use products (even if diluted) containing chlorine (sodium hypochlorite, hydrochloric or muriatic acid, etc.) to clean the appliance or the floor under it. • Do not spray water or use water jets or steam to clean the equipment. •...
• The connection point has an efficient earth contact and the mains voltage and frequency match that given on the data plate. In case of doubts regarding the efficiency of the earth wire, have the system checked by specialised personnel; •...
B APPLIANCE AND MANUFACTURER’S IDENTIFICATION DATA IMPORTANT The hood works only in the presence of the Electrolux Professional SkyLine Range oven, for which it was designed. Data plate position This instruction manual contains information relevant to various appliances. See the data plate located on the left side to identify the appliance (see the picture below).
It is advisable to read them This manual is intended solely for consultation by the carefully before use. operator and can only be given to third parties with the permission of Electrolux Professional SpA. Operator machine installation, adjustment, use, maintenance,...
Manufacturer Electrolux Professional SpA or and uses it (e.g. company, any other service centre entrepreneur, firm). authorised by Electrolux Electrocution an accidental discharge of Professional SpA. electric current on a human Operator for an operator who has been body. normal...
D TRANSPORT, HANDLING AND STORAGE D.2.3 Placing the load D.1 Introduction • Before placing the load, make sure the way is free Transport (i.e. transfer of the machine from one place and that the floor is flat and can take the load. to another) and handling (i.e.
Any missing or faulty parts must be replaced with original parts. 10 ℃ [14 ℉ and 50 ℃ [122 ℉]. E TECHNICAL DATA Technical data - models PNC – MODELS 922723 HOCT11E 922728 HOST11 922724 HOCT21E 922729 HOST21 922725 HOCV11E 922730 HOSV11...
• Keep the hood evenly balanced to prevent it from tipping over. FRONT Remove the copper staples and the cardboard • take into account the size and access space. from the appliance; FRONT Width MODELS inches 922728 HOST11 344,49 922723 HOCT11E 344,49 922732 HOSS11 344,49 922727 HOCS11E 344,49...
F.3.3 On hood for stacked ovens The following items are supplied with a kit for stacking ovens: 922726 HOCS21E 922727 HOCS11E 922731 HOSS21 922732 HOSS11 1. Unscrew to remove the rear panel of the hood; 2. assemble the pipe and seal supplied; 3.
In some cases, the following items could be installed under a hood or ventilated ceiling. Therefore it is not possible for them to be connected to a centralised system as suggested above. 922728 HOST11 922729 HOST21 922730 HOSV11 922731 HOSS21...
• Install ahead of the appliance an omnipolar duct: switch of suitable capacity with contact gap of at least 3 mm. Install the switch in the 922728 HOST11 building's electrical system, in the immediate 922732 HOSS11 vicinity of the appliance;...
• Install ahead of the appliance a device F.8.2 Hood-oven interface cable (interlocked plug, lockable switch or similar The hood is supplied with an Interface Cable; to devices) lockable in the open position during connect it, proceed as follows: maintenance; •...
COMMISSIONING AND SETTINGS Introduction CAUTION G.2 Oven settings Make sure the appliance is When the hood is switched on for the first time, connected to a water execute following procedure on Oven: drainage system, a power AL01 IM_HO_L1_L2_L3_L4 socket, and to the oven with TOUCH Oven (see annex document) or via the oven/hood AL02 IM_HO_L1_L2_L3_L4...
MACHINE SCRAPPING of in a differentiated way, according to their WARNING different characteristics (e.g. metals, oils, greases, Refer to plastic, rubber, etc.). “WARNINGS and Different regulations are in force in the various Safety Information “ countries, therefore comply with the provisions of the laws and competent bodies in the country where scrapping takes place.