Samsung CLX-6220FX User Manual page 116

Message Meaning
Paper Empty in There is no paper in
[yyy]
the tray.
Paper is empty in
[yyy]
Load paper
Paper Mismatch The paper size
[yyy]
specified in the printer
Load [zzz][xxx]
properties does not
Continue Cancel
match the paper you
are loading.
BOOTP problem There is a problem with
the network.
BOOTP has a
problem. Switching
to Auto IP
DHCP problem There is a problem with
the network.
DHCP has a
problem.
Reconfigure
BOOTP/static IP
DHCP problem There is a problem with
the network.
DHCP has a
problem. Switching
to Auto IP
BOOTP problem There is a problem with
the network.
BOOTP has a
problem.
Reconfigure
DHCP/static IP
Replace [ccc] toner The toner cartridge has
reached the end of its
Replace with new
lifespan.
[ccc] Toner
Replace Fuser unit The fuser unit has
reached the end of its
Replace with new
lifespan.
fuser unit
Retry Redial? The machine is
waiting for a specified
time interval to redial
a previously busy
station.
Scanner door Open The scanner door is not
securely latched.
Door of scanner is
open.
Close it
Scanner locked The scanner module is
locked.
Scanner locking
switch is locked.
Release it
Suggested solutions
Load paper in the tray
(See "Loading paper in
the tray" on page 3).
You can select the
option between
Continue or Cancel. If
you select Cancel , the
printing job will stop.
Load the correct paper
in the tray. If you select
Continue, printing job
will continue.
Check your network
environment, or contact
your network
administrator.
Check your network
environment, or contact
your network
administrator.
Check your network
environment, or contact
your network
administrator.
Check your network
environment, or contact
your network
administrator.
Replace the toner
cartridge with a
Samsung-genuine toner
cartridge (See
"Replacing the toner
cartridge" on page 2).
This message appears
when the fuser unit is
worn. Replace the fuser
unit with a new one. Call
for service.
You can press OK to
immediately redial,
Stop/Clear to cancel
the redial operation.
Close the scanner door
until it locks into place.
Unlock the CCD (See
"Front view" on page 1).
Or turn off the machine
and on again. If the
problem persists, call
for service.
Troubleshooting_ 11
Message Meaning
Self Diagnostics The engine in your
printer is performing self
Please Wait...
diagnostics.
Send Error There is a problem in
DNS.
There is a problem
in DNS
Send Error There is a problem in
POP3.
There is a problem
in POP3
Send Error There is a problem in
SMTP.
There is a problem
in SMTP
Send Error There is a problem in
SMTP authentication.
There is a problem
in SMTP
authentication
Send Error There is a problem on
network interface card.
There is a problem
on the NIC Card
Sensor Failure There is a problem in the
sensor signal.
[aaa]
Turn off then on
Mail Size Error The mail size is larger
than the supported size
Mail exceeds than
by SMTP server.
server support
System error There is a problem in the
machine.
Error: [aaa]
Turn off then on
Mail Size Error Single page data
exceeds the configured
One Page is
mail size.
Too Large
Too many Faxes Too many faxes are
received.
Too may faxes are
received. Print or
remove job
Too many Faxes Too many faxes are
queued to be sent.
Too may faxes are
queued. Wait or
remove job
TR belt Not installed The transfer belt is not
installed.
Transfer belt unit is
not installed.
Install it
TR. belt Not The transfer belt of the
compatible machine is not for your
machine.
Transfer belt unit is
not compatible.
Check guide
Transfer belt is low The life of the transfer
belt will expired soon.
Transfer belt unit
will be worn.
Order new one
Suggested solutions
Please wait a few
minutes.
Configure the DNS
setting.
Configure the POP3
setting.
Change to the available
server.
Configure the
authentication setting.
Turn the power switch
off and on. If the
problem persists, call
for service.
Turn the machine off
and turn it on again. If
the problem persists,
call for service.
Divide your mail or
reduce the resolution.
Turn the machine off
and turn it on again. If
the problem persists,
call for service.
Reduce the resolution
and try again.
Print or remove
received fax.
Cancel reserved fax in
priority fax feature.
Install a
Samsung-genuine
transfer belt.
Install the a
Samsung-genuine part
designed for your
machine.
Order a transfer belt
(See "Available
accessories" on
page 2).