Sealey ADT7.V2 Quick Start Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear protective
instruction gloves
manual
1. SAFETY
WARNING! Ensure all preliminary checks are carefully carried out before using gearbox support and transmission jack.
‰
WARNING! Follow all of the safety instructions issued with the transmission jack.
‰
WARNING! Ensure load is placed level and centrally on gearbox support and is fixed in place before attempting to lift, lower, or
‰
transport load. Always use load restraint chains and attachments to stabilise and secure the load to the gearbox support.
Before use ensure the transmission weight and size DO NOT exceed the capacity of the gearbox support or the transmission jack.
9
The gearbox support is heavy, care should be taken when placing onto the transmission jack.
9
Ensure that the sliding bracket and chain mount bracket nuts and bolts are fully tightened when the gearbox support is loaded.
9
Care should be taken when using the gearbox support and vertical transmission jack in conjunction with a vehicle lift to ensure that the
9
vehicle is not lowered whilst the jack is in position.
Before storing ensure gearbox support is clean and free of grease and oil.
9
Store in a safe, dry childproof location.
9
DO NOT use the gearbox support without restraint chains.
8
DO NOT replace the chains with an inferior form of restraint.
8
DO NOT allow untrained persons to use the gearbox support.
8
DO NOT move the transmission jack, with or without a load, with the gearbox support in the raised position.
8
DO NOT use the gearbox support for any purpose other than for vehicle transmissions.
8
2. INTRODUCTION
i
Fully adjustable saddle with forward, backward and side to side tilt. Suitable for use with Model Nos: 300ETJ.V2 and 500ETJ.V2.
3. SPECIFICATION
i
Model No: .................................................................ADT7.V2
Capacity: ...................................................................... 500kg
Compatibility: .................................... 300ETJ.V2, 500ETJ.V2
Net weight ................................................................. 12.02kg
4. ASSEMBLY
Item Description
1 Main Support
2 Support Plate
3 Adjuster Screw
4 Pivot Pin
5 Sliding Bracket
6 Chain Mount Bracket
7 M8 Bolt and Nut
8 Chain Hook
9 M10 x 30mm Bolt
WARNING! Failure to assemble the gearbox support correctly may result in serious damage and/or personal injury. Unpack
‰
the product and check contents against the contents list. Should there be any damaged or missing parts contact your supplier
immediately.
4.1. ASSEMBLY (refer to fig.1)
4.1.1. Position the support plate (2) on a flat surface with the bracket facing upwards. Place the main support (1) over the support plate (2) so
that the bracket fits into the slot on the main support (1).
© Jack Sealey Limited
ADJUSTABLE GEARBOX SUPPORT 500KG
CAPACITY SUITABLE FOR MODELS 300ETJ.V2
AND 500ETJ.V2
MODEL NO:
Wear protective Wear safety
clothing footwear
Qty Item Description
01 10 Flat Washer
01 11 Spring Washer
02 12 M10 Nut
01 13 Circlip
02 14 Split Pin
04 15 Chain
02 16 Retaining Bolt
02 17 Reduction sleeve
06
Original Language Version
ADT7.V2
Qty
06
10
10
02
01
02
02
01
fig.1
ADT7.V2 Issue 3 (H, F) 07/09/18