Bodet 8000 Installation Manual
  1. Manuals
  2. Brands
  3. Bodet Manuals
  4. Sports & Outdoors
  5. 8000
  6. Installation manual

Bodet 8000 Installation Manual

Sports scoreboard
Hide thumbs
Table of Contents

Advertisement

Quick Links

8000 Sports Scoreboards
Installation manual
BODET Time & Sport
1 rue du Général de Gaulle
49340 Trémentines I France
Tel: +33 (0)2 41 29 06 00
www.bodet-sport.com
Upon receipt, always check the product for damage during shipment, if any is found you may file a damage claim with
the carrier.
1

Advertisement

Table of Contents
loading

Related Manuals for Bodet 8000

Summary of Contents for Bodet 8000

  • Page 1 8000 Sports Scoreboards Installation manual BODET Time & Sport 1 rue du Général de Gaulle 49340 Trémentines I France Tel: +33 (0)2 41 29 06 00 www.bodet-sport.com Upon receipt, always check the product for damage during shipment, if any is found you may file a damage claim with...

  • Page 2: Table Of Contents

    5. INSTALLING 8000 SCOREBOARDS 5.1 Attachment to wall bracket (Ref.: standard scoreboard reference) 5.2 Mounting on existing BODET wall bracket (ref: 916 427) 6 5.3 Suspended mount (ref: 916 426) 5.4 Mounting from the back (Ref.: standard scoreboard reference) 7 5.5 Electrical connections...

  • Page 3: Ntroduction

    2. ELECTRICAL AND MECHANICAL SAFETY STANDARDS This equipment should be installed and maintained by qualified personnel. As 8000 sports scoreboards are connected to the mains electricity supply, they must be installed in compliance with IEC 364 (NFC 15.100 in France).

  • Page 4: Required Tooling

    5. INSTALLING 8000 SCOREBOARDS This chapter presents the installation method for central boards in the 8000 range: 8015, 8020, 8025, 8T120 and 8T125. The mounting principle as well as the dimensions (and centre distances) are identical for models 8020, 8025, 8T120 and 8T125.
  • Page 5 2) Install the scoreboard sliding it into the wall bracket keyhole slots (B). Caution: run the cables before attaching the scoreboard to the wall (power cables and console cable in case of wired communication). 3) Lock the board to the wall bracket by tightening the screw (C). 4) Put in and tighten the screws at each end of the board: 5) Make the electrical connections.

  • Page 6: Mounting On Existing Bodet Wall Bracket (Ref: 916 427)

    5.2 - Mounting on existing BODET wall bracket (ref: 916 427) If a 8000 range scoreboard is to be installed in place of a scoreboard of an older range, it is possible to adapt the installation without having to get rid of everything of the old installation.

  • Page 7: Suspended Mount (Ref: 916 426)

    5.3 - Suspended mount (ref: 916 426) Suspended mounting requires a lifting solution, which must be determined and installed by the client. 1) On the ground, attach the lifting eye bolts (ref: 916 426) to the top of the scoreboard. Centre to centre dimensions between eye bolts: 1906 mm 2) Attach the two quick links to the lifting eye bolts.
  • Page 8 2) Mount the scoreboard according to the followinf dimensions: Main scoreboard Individual fouls Individual fouls module module Additional fouls module Main scoreboard Individual fouls Individual fouls module module Individual Individual scores module scores module Additional fouls module Front view Rear view...

  • Page 9: Electrical Connections

    5.5 Electrical connections 5.5.1. HF installation 1) Remove the lower right hatch by the 3 screws («Guest score» hatch or «Guest penalties» hatch according to the scoreboard model): 8Txx or 8NTxx scoreboards 80xx scoreboards (Only one electronic card for the 8T120 SOLO) 2) Feed the power cable through the grommet: - feeding through the back (A) - feeding through the bottom (B)
  • Page 10 Connect the 2 wires (brown and white) on the lever connectors, for the keyboard communication coming from the DIN type wall outlet. > Observe the colours for connection. 8Txx or 8NTxx scoreboards 80xx scoreboards (Only one electronic card for the 8T120 SOLO) NOTE: disconnect the Brown yellow and green...
  • Page 11 3) Feed the power cable through the grommet: - feeding through the back (A) - feeding through the bottom (B) 8Txx or 8NTxx scoreboards (Only one electronic card for the 8T120 SOLO) 80xx scoreboards 4) Connect the cable to the electrical main (100-240VAC power supply). 5) Put the hatch back in place.

  • Page 12: Installing Additional Modules

    6. INSTALLING ADDITIONAL MODULES This chapter explains how to install a 8000 series additional module. Mounting instructions are identical regardless of the scoreboard model: 2NT15, 3NT15, 2T10, 2T20 or sheet metal advert panel Reminder: the additional module must be assembled with the main scoreboard on the ground.
  • Page 13 3) Attach the additional module to the central scoreboard (8015, 8020 or 8025) with the 2 supplied M10 screws andfeed the power and communication cables of the additional module (A) to the main scoreboard : Communication: grey cable with 1 brown wire + 1 white wire Power supply: yellow/green - blue - brown...
  • Page 14 3)Wiring: Feed the additional module cables in the main scoreboard through the grommets. > Communication of the additional module with the main scoreboard: 2 wires have to be connected to the main scoreboard. These wires are supplied with the additional module and are to be connected using quick connectors supplied in the main scoreboard unit.
  • Page 15 Dimensions of additional modules: 65.5 2000 2NT15 (Ref.: 916 405). 65.5 2000 3NT15 (Ref.: 916406). 65.5 1200 2T10 (Ref.: 916401). 65.5 2000 2T20 (Ref.: 916402). 65.5 1200 PUB A (Ref.: 916422). 65.5 2000 PUB B (Ref.: 916421). 65.5 PUB C (Ref: 916423). 65.5 2000 PUB D (Ref: 916424).

  • Page 16: Individual Foul Panel Installation

    7. INDIVIDUAL FOUL PANEL INSTALLATION 7.1 Opening an F6 individual foul panel This chapter presents the installation method for an F6 individual foul panel in the 8000 range. The mounting principle is identical for F10 and FS10 individual foul panels Reminder: the additional module must be assembled with the main scoreboard on the ground.
  • Page 17 4) Using lifting eye bolts (ref.: 916 426), lift the module at the height of the central panel. Lifting eye bolts to be placed here Cables are run to the central board (the metal Electronic board plate is pre-cut for creating the hole) Power supply unit Earthing terminal...
  • Page 18 6) Wiring on the main scoreboard panel Feed the individual fouls module cables in the main scoreboard through the grommets. > Communication of the individual fouls module with the main scoreboard: 2 wires have to be connected to the main scoreboard. These wires are supplied with each of he individual fouls modules and are to be connected using quick connectors supplied in the main scoreboard unit.

  • Page 19: Installation Configurations

    7) Connect the ground to each metal plate and put them back in place. Dimensions and weight of individual fouls modules: 65.5 F6 (Ref.: 916 410). 65.5 F10 (Ref.: 916 411). 65.5 FS10 (Ref.: 916412). 8. INSTALLATION CONFIGURATIONS The configuration of the scoreboards is carried at the factory according to the information (numbers of panels, models, communication) that you provided us at order time...

Table of Contents