Content Symbol, Connection ..................Warning ......................Characteristics ....................Technical parameters ..................Versions of time switches, Load ..............Description ....................8 - 9 Control ......................Mode precendence, Manual output control ..........Program setting ..................... Program adjustment ..................Program deleting, Deleting of all programs ..........Date and time setting ...................
Warning Device is constructed for connection in 1-phase exceeded. For installation and setting use screw-driver cca main alternating current voltage and must be 2 mm. The device is fully-electronic - installation should installed according to norms valid in the state be carried out according to this fact.
Versions of time switches). time. - SHT-1, SHT-3: 1-channel version. - 100 memory positions (by SHT-1/2 and SHT-3/2 are - SHT-1/2, SHT-3/2: 2-channel version (to each channel those 100 positions common for both channels). can be assigned an individual program).
Versions of time switches output time program Type of product 1 channel 2 channels week month year SHT-1 SHT-1/2 SHT-3 SHT-3/2 Load Type of load HAL.230V cos φ ≥ 0.95 AC5a AC5a Uncompensated AC5b Compensated Contact material AgSnO 230V / 3A (690VA)
Description Output - channel 1 (16-15-18) Supply voltage terminal (A1) Display with back-light Control buttons Place for seal Supply voltage terminal (A2) Output - channel 2 (26-25-28) - 8 -...
Page 9
Indicates the day in the week Indication (2nd channel) Operating modes indication Auto Prog Indication (1st channel) Indicates 12 / 24 mode Indication of time/date/setting menu Indicates summer / winter mode Bargraf Control button MAN2 / ESC Control button PRG / + Reset Control button OK Control button MAN1 / -...
Device diff ers short and long button press. In the manual marked as: Control - short button press (<1s) - long button press (>1s) - number indicates button press sequence Prog setting, adjustment - entrance into programming menu and program deleting ...
ON / OFF normal mode Prog controlling mode Manual output control - is superior to other set modes - controls channel 1 - controls channel 2 (by SHT-1/2 and SHT-3/2) relay on relay off - 11 -...
SET 1 Program setting Prog Prog ... . - by SHT1/2 - by SHT-3 and - add a new and SHT3/2 SHT-3/2 program - setting of - selection of only by daily - selection of...
SET 1 Program adjustment Prog EDIT - selection - adjustment - by SHT-1/2 and only by daily / entrance of already SHT-3/2 - by SHT-3 and mode: into chosen saved selection / SHT-3/2 ON/OFF - only by...
SET 1 Program deleting Deleting of all programs Prog - program - in starting - press button DEL - deleting selection menu (time to complete the of individual - long press is shown on deleting of all set programs - deleting of...
SET 2 Date and time setting Prog year month setting setting setting of time setting in 24 or 12 hour hour activation of format minutes setting changeover setting between summer/winter time - long press (>1s) - short press (<1s) - press sequence - 15 -...
SET 3 Setting of programmed / random mode Prog Auto Prog PROG AUTO - by SHT-1/2 and SHT-3/2 - relay is - relay is - selection of switching switching channel according randomly in programs set in 10-120 min...
SET 4 Setting of pulse / cyclic mode interval Prog - by SHT-1/2 and SHT-3/2 - setting of - setting of selection of delay / cycle pulse /cycle channel duration duration - pulse mode do not set) - long press (>1s)
Exit from menu - return to the starting mode Prog Activated by, covered RESET button, short press with blunt spike (with max. 2mm diameter). After press, information about type of device and fi rmware version will displayed for 3 s and then device performs in starting mode. Reset will delete an actual time, set time of pulse/cyclic mode and all temporary functions (manual or random switch output).
Example of programming Setting of SHT-3/2 to be activated from Monday till Friday at 8:00 by program 0 , and deactivated from Monday till Friday at 16:30 by program 1 setting of switching on Prog ... . ...